Automotive Technology: A Systems Approach (MindTap Course List)
6th Edition
ISBN: 9781133612315
Author: Jack Erjavec, Rob Thompson
Publisher: Cengage Learning
expand_more
expand_more
format_list_bulleted
Concept explainers
Textbook Question
thumb_up100%
Chapter 10, Problem 9ASRQ
While preparing to remove an engine: Technician A turns the crankshaft pulley to set the engine at number 1 cylinder TDC. Technician B removes the drive belt and crankshaft pulley. Who is correct?
- Technician A
Expert Solution & Answer
Trending nowThis is a popular solution!
Students have asked these similar questions
Technician A says the torque converter uses engine oil to provide a fluid link between engine and transmission. Technician B says the torque converter is attached to the engine crankshaft and receives the engine torque output. who is correct?
Technician A says that most transaxles have a countershaftbetween the main and output shafts. TechnicianB says that a countershaft is always in motionwhen the engine is running. Who is correct?a. Technician A onlyb. Technician B onlyc. Both A and Bd. Neither A nor B
A six-cylinder engine has a 1 5 3 6 2 4 firing order. Technician A says that after cylinder number 1 begins its intake stroke, the crankshaft will have to travel 240° before cylinder number 3 begins its intake stoke. Technician B says that when cylinder number 3 and 4 are at TDC, cylinders number 5 and 2 are at BDC.
Who is correct and explain why?
Technician A
Technician B
Both A and B
Neither A nor B
Chapter 10 Solutions
Automotive Technology: A Systems Approach (MindTap Course List)
Ch. 10 - WHat should be worn when working with any type of...Ch. 10 - Prob. 2RQCh. 10 - What is the best way to lift a vehicle when...Ch. 10 - True or False? The first step in removing an...Ch. 10 - Prob. 5RQCh. 10 - The buildup of minerals and deposits inside the...Ch. 10 - Hydrocarbon solvents are. flammable toxic both a...Ch. 10 - Prob. 8RQCh. 10 - Which cleaning method uses high-frequency sound...Ch. 10 - Parts must be when they go into an abrasive blast...
Ch. 10 - Prob. 11RQCh. 10 - Which of the following is not considered part of...Ch. 10 - Why should a memory saver be installed before dis...Ch. 10 - Which of the following statements is not true...Ch. 10 - Which of the following is not a common way to...Ch. 10 - While working on an engine with an excessive...Ch. 10 - While discussing the common causes for cracks...Ch. 10 - Technician A uses a crane to remove an engine from...Ch. 10 - Prob. 4ASRQCh. 10 - While discussing abrasive cleaners: Technician A...Ch. 10 - Technician A labels or marks all electrical wires...Ch. 10 - While discussing cleaning engine parts: Technician...Ch. 10 - While loosening the axle shaft hub nuts on a FWD...Ch. 10 - While preparing to remove an engine: Technician A...Ch. 10 - After removing the vehicles hood in preparation...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- True or False? The first step in removing an engine is usually the removal of the intake and exhaust manifolds.arrow_forwardTechnician A says that crankshaft counterweights offset the weight of the connecting rods and pistons. Technician B says that crankshaft counterweights are used to dampen crankshaft torsional vibrations. Who is correct? Technician A Technician B Both A and B d. Neither A nor Barrow_forwardWhich of the following statements about engines is not true? The engine provides the rotating power to drive the wheels through the transmission and driving axle. Only gasoline engines are classified as internal combustion. The combustion chamber is the space between the top of the piston and the cylinder head. For the combustion in the cylinder to take place completely and efficiently, air and fuel must be combined in the right proportions.arrow_forward
- A vehicle is producing a sharp, metallic rapping sound originating in the upper portion of the engine. It is most noticeable during idle. Technician A diagnoses the problem as piston pin knock Technician B says that the problem is most likely a loose crankshaft thrust bearing. Who is correct? Technician A Technician B Both A and B Neither A nor Barrow_forwardWhile discussing the reasons for resurfacing a cylinder head; Technician A says it should be resurfaced to make it flat and very smooth so the head gasket can seal properly during engine assembly. Technician B says that it can be resurfaced to raise the compression. Who is correct? Technician A Technician B Both A and B Neither A nor Barrow_forwardWhich of the following are not typically found in the block of a modern engine? a. Pistons b. Crankshaft c. Valves d. Oil pumparrow_forward
- While checking a hydraulic phaser after the camshaft has been removed from the engine: Technician A attempts to rotate the phasers timing gear by hand and replaces it if it does not move. Technician B applies air pressure to the advance and retard ports and replaces it if the gear does not move. Who is correct? Technician A Technician B Both A and B Neither A nor Barrow_forwardTrue or False? To eliminate the drain of engine power during times when cooling fan operation is not needed, many of todays belt-driven fans have a fan clutch that prevents the operation of the fan when the engine and radiator are heated up.arrow_forwardTechnician A says that most transaxles have a countershaft between the main and output shafts. Technician B says that a countershaft is always in motion when the engine is running. Who is correct? a. Technician A only b. Technician B only c. Both A and B d. Neither A nor Barrow_forward
- An engine cranks slowly: Technician A says that a possible cause of the problem is poor starter circuit connections. Technician B says that an engine problem could be the cause. Who is correct? Technician A Technician B Both A and B Neither A nor Barrow_forwardTechnician A checks crankshaft oil clearance with a feeler gauge. Technician B uses a dial indicator to check crankshaft oil clearance. Who is correct? Technician A Technician B Both A and B Neither A nor Barrow_forwardWhile discussing the causes of extreme engine bearing damage Technician A says that contaminated and old engine oil could be the cause. Technician B says that a leaking radiator could be the cause. Who is correct? Technician A Technician B Both A and B Neither A nor Barrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Automotive Technology: A Systems Approach (MindTa...Mechanical EngineeringISBN:9781133612315Author:Jack Erjavec, Rob ThompsonPublisher:Cengage LearningAutomotive TechnologyMechanical EngineeringISBN:9781337794213Author:ERJAVEC, Jack.Publisher:Cengage,
Automotive Technology: A Systems Approach (MindTa...
Mechanical Engineering
ISBN:9781133612315
Author:Jack Erjavec, Rob Thompson
Publisher:Cengage Learning
Automotive Technology
Mechanical Engineering
ISBN:9781337794213
Author:ERJAVEC, Jack.
Publisher:Cengage,
Power Transmission; Author: Terry Brown Mechanical Engineering;https://www.youtube.com/watch?v=YVm4LNVp1vA;License: Standard Youtube License