(a)
The additional power required by the Recreational vehicle at given condition.
Answer to Problem 104P
The additional power required by the recreational vehicle,
Explanation of Solution
Given information:
Concept used:
Calculation:
The gas constant is,
Refer the table 11.2 from the textbook, for horizontal cylinder of
Conclusion:
The additional power required by the recreational vehicle is
(b)
The additional power required by the recreational vehicle at given conditions.
Answer to Problem 104P
The additional power required by the recreational vehicle,
Explanation of Solution
Given information:
Concept used:
Calculation:
The gas constant is,
Refer the table 11.2 from the textbook, for vertical cylinder of
Conclusion:
The additional power required by the recreational vehicle,
Want to see more full solutions like this?
Chapter 11 Solutions
Fluid Mechanics: Fundamentals and Applications
- 9. The gas density is 0.75 kg per cubic meters and air density is of 1.15 kg per cubic meter. If thedriving pressure is 0.25 KPA. Determine the height of the chimney. 10. A powerplant situated at an altitude having an ambient air of 96.53 KPa and 23.88 degreeCelsius. Flue gases at a rate of 5.0 kg per second enter the stack at 200 degree Celsius andleaves at 160 degree Celsius. The flue gases gravimetric analysis are 18% CO2, 7% O2 and 75%N2. Calculate the height of the stack necessary for a driving pressure of 0.20 KPaKindly answer all please. Thank youarrow_forwardA wind turbine generator system having a diameter of 82.5 m produces 1.5 MW at a wind speed of 12 m/s. Determine the diameter of blade necessary to produce 10 MW of power assuming the efficiency is the same for both designs and p = 1.21 kg/m3 for air.arrow_forwardDetermine the width of a a.) apron conveyor b.) flight conveyor without skirts whose capacity is 56 tons per hour at a speed of 50 fpm handling solids with an average density of 50 pounds per cubic foot.arrow_forward
- Flood in irrigation areasto block and return the water to the river or wateras below to guide your bedThe flat cover system provided is preferred. Of coverits weight is 871 kg. Square section cover, coverhinged 1 m above center (a = 0.25 m)and b = 150 cm. Cover vertically 4 °has angle. According to the givenWhat is the maximum water head (h) for not openingshould be up. (ρ water = 1000 kg / m3)arrow_forwardA chair lift is to be installed from the surface down to a depth of 150 m. The inclination is 17 degrees to the horizontal. An operating velocity is to be used, and the system will be required to transport 300 persons per hour. Assuming the worst-case scenario, namely that no persons travel down while the system has a full load traveling up, determine: 1. the spacing of thr chairs 2. the traveling time per person 3. the output power of the motor required to drive the system Perfomance criteria: A force criteria: A force of 2 kN per 100 m of the length of the loaded part of the system is required to overcome friction. Mass per person: 70 kg Overall mechanical efficiency: 85%arrow_forwardA wooden block having a weight of 50 N isplaced at a distance of 1.5 m from the center ofa circular platform rotating at a speed of 2rad/sec. Determine the minimum coefficient offriction between the block and the platform sothat thearrow_forward
- At highway speeds, about half of the power generated by the car’s engine is used to overcome aerodynamic drag, and thus the fuel consumption is nearly proportional to the drag force on a level road. Determine the percentage increase in fuel consumption of a car per unit time when a person who normally drives at 55 mi/h now starts driving at 70 mi/h.arrow_forwardAdvertisement signs are commonly carried by taxicabs for additional income, but they also increase the fuel cost. Consider a sign that consists of a 0.30-m-high, 0.9-m-wide, and 0.9-m-long rectangular block mounted on top of a taxicab such that the sign has a frontal area of 0.3 m by 0.9 m from all four sides. Determine the increase in the annual fuel cost of this taxicab due to this sign. Assume the taxicab is driven 60,000 km a year at an average speed of 50 km/h and the overall efficiency of the drive train is 28 percent. Take the density, unit price, and heating value of gasoline to be 0.72 kg/L, $1.10/L, and 42,000 kJ/kg, respectively, and the density of air to be 1.25 kg/m3.arrow_forwardTo determine the frictional stress exerted by fluid on a smooth wall, velocities v, and v2are measured in the turbulent zone at distances y, and y2 from the wall. Derive an expression forthe frictional stress in terms of the four measured quanities and the fluid density.arrow_forward
- Which car is more likely to be more fuel-efficient: one with sharp corners or one that is contoured to resemble an ellipse? Why?arrow_forwardCommercially available large wind turbines have blade span diameters as large as 100 m and generate over 3 MW of electric power at peak design conditions. Consider a wind turbine with a 90 m blade span subjected to 25 km/h steady winds. If the combined turbine generator efficiency of the wind turbine is 32 percent, determine(a) The power generated by the turbine.(b) The horizontal force exerted by the wind on the supporting mast of the turbine.Take the density of air to be 1.2 kg/m3and disregard frictional effects.arrow_forwardA tank is in the form of a right circular cylinder with hemispherical ends. The overall length of the tank is4 meters and the diameter of the hemisphere is 1 meter. If a pump discharges a fluid whose density is1.2 kg m /Liter in this tank at a rate of225 liters per minute determine a.) Weight of liquid inside the tank ifit is half full. b) total time to fill the tank assuming it is initially empty.arrow_forward
- Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University PressMechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSONThermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
- Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEYMechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage LearningEngineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY