Technician A installs a cup-type core plug with its flanged edge outward. Technician B installs a dish-type core plug with the dished side facing inward. Who is correct

Q: Diagram a circuit that would allow for the manual lowering of a load on a cylinder using a simple…

A:

Q: List the procedures used when setting up, igniting, andusing an air-acetylene unit.

A: The procedures used when setting up, igniting, and using an air-acetylene unit are given as under,

Q: Protects the shaft where it passes through the stuffing box A shaft sleeve B impeller casing…

A: A Shaft Sleeve is cylindrical shape made of metal which is used to protect the Shaft so that the…

Q: Galvanized shet has a protective coating of- -in steel shects. Sodium Aluminum Magnesium Oc Zinic

A: Galvanization or galvanizing  is the process of applying a protective zinc coating to steel or iron,…

Q: _______ is a cylindrical piece of metal used to carry rotating machine parts such as pulleys and…

A: A shaft is a rotating machine element, usually circular in cross-section, which is used to transmit…

Q: B 100 lbf 10 in AC - 10 in- - 10 in- 10 in

A: P= 100 lbf

Q: You are to draw suitable hydraulic circuit based from the given figure. MAIN RELIEF STATIONARY VALVE…

A: Given : To find : Hydraulic circuit

Q: Explain the operation of Buchholz relay.

A: Buchholz relay Buchholz relay in a transformer is an oil tub containing the connecting line from the…

Q: Which one of the following reboiler requires more complex pipe work? Horizontal thermosyphon…

A: Horizontal thermosyphon reboiler are depends on natural circulation where in shell sides,…

Q: QUESTION An operator working on an operation involving particularly high pressures would likely use…

A: A composite material made of ceramic and metallic components is known as cermet. Metal may go…

Q: What is the Power input range of venturi scrubbers?

A: Venturi scrubbers: It is a converging-diverging flow channel. It means in this system the area is…

Q: Correct the view that is incomplete. Subject: blueprint for welders

A: In drawing, the holes if not visible directly are shown by dotted line because drawing is the…

Q: Which of the following material is used to connect D Select one: Square box Saddle clip Coupling…

A: Option c is correct.

Q: Master cylinder that is the terms used in

A: Brake  Pump

Q: Using the Unit Load Method

A:

Q: a. Explain resonant earthing system with diagram b. How will you give Combined Leakage and Overload…

A: (a) Resonant earthing system : Resonant earthing is a sure uncommon sort of high impedance earthing…

Q: What are Ball and socket connections

A: The ball and socket connection  also known as spheroid joint, is a type of joint in which the…

Q: Problem (2): By Inspection (no calculation), identify the zero-force members in Figure (a) and…

A: Given data: Figure 'a'find zero - force member (inspection)

Q: Make the definition of Spring Pin and what are the advantages and disadvantages

A: Spring Pin: It is an mechanical fastener. Spring pin is used to tight the relative positon of  two…

Q: B2. Explain the function of Thermocouple with neat diagram and mention its advantages.

A: The thermocouple is a thermoelectric device that is used for temperature sensing. It is based on See…

Q: Technician A says that rigid metal transmission lines are made of steel. Technician B says rigid…

A: The rigid metal transmission line is a very important part of the power transmission system. The…

Q: When the compressor and motor operate on the same shaft and are enclosed in a common casing is known…

A: This question is based on the concept of semi hermetic sealed compressor

Q: Describe the action of a commutator.

A: Introduction to commutator: commutator is a mechanical part of DC generator or motor which converts…

Q: Difference between ESW and EGW

A: Both the Electroslag welding and Electrogas welding are almost identical with similar kind of…

Q: List some factors of safety for design of drilled shafts.

A: A drilled shaft is a deep foundation that is constructed by placing fluid concrete in a drilled…

Q: The contact factor for a heating coil-36

A: The contact factor of heating is coil can be determined by the efficiency for dehumidification. The…

Q: List two types of grinders used by welders.

A: welding is a joining process in which two metallic pieces are jointed with the help of heat or…

Q: Which of the following steam traps is preferred primarily for plate and tube coils operating under…

A: Free Float traps are more vitality proficient and strong within the same administrations, so…

Q: The largest aluminum tube that should be flared with a double flare has an outside diameter of…

A: The largest aluminum tube that should be flared with a double flare has an outside diameter of

Q: 5 inch dia. shafts coupling to connect the equipment shafts. Note: use 4 bolts only nstructions:

A:

Q: Enlist the names of places on aeroplane where the pitot-static tubes are located.

A: A pitot-static system is a setup comprising of pressure-sensitive instruments and is mostly used in…

Q: Technician A installs a cup-type core plug with itsflanged edge outward. Technician B installs a…

A: Core plugs are used to close the holes created while molding engine block to remove the sand from…

Q: Describe the following point-of-operation devices: (a) automatic or semiautomatic feed and ejection…

A:

Q: orrect

A: GIVEN:

Q: Importance of Dual side working system using scotch yoke mechan

A:

Q: Which type of crucible is not found in crucible stoves? A) should remove B) fixed C) the crucible of…

A: Crucible :-  A crucible is a metallic container which is used to melt the various metals at higher…

Q: a) What happens if the DCV is in its upper position ? b) What happens if the DCV is in its lower…

A:

Q: How many main bearings are in the ?shown engine

A: Ans: 6

Q: What should you do if you have to leave a piece of hotmetal unattended?

A: A responsible person should mark any hot metal with "HOT" before leaving the office in order to…

Q: The following are main part of Globe type control valve EXCEPT A. Stem В. Connector C. Seat D. O…

A: Globe valve: A globe valve is a control valve used to stop, start or regulate the fluid flow.

Q: What is the lowest acceptable amperage setting for GTAwelding?

A: Gas tungsten arc welding (GTAW), also known as tungsten inert gas (TIG) welding, is an arc welding…

Q: Describe with mechanism abut how a boiler feed water telreatment sytem work

A: given; Describe with mechanism about how a boiler feed water treatment system work

Q: Explain why all the fuel in a nuclear reactor is not placed in a single fuel rod

A: The fuel in a nuclear reactor is not placed in a single fuel rod due to following reasons:   a. The…

Q: The surface of the pressure plate contacts?

A: According to Laymen’s terms, the pressure plate is like a clamp with spring-loaded that is attached…

Q: procedure of welding split airconditioner leakage in steps

A: Given Aircondtioner leakage To find Welding of split airconditioner leakage