Automotive Technology: A Systems Approach (MindTap Course List)
6th Edition
ISBN: 9781133612315
Author: Jack Erjavec, Rob Thompson
Publisher: Cengage Learning
expand_more
expand_more
format_list_bulleted
Videos
Textbook Question
Chapter 11, Problem 6ASRQ
Technician A uses a micrometer to measure the connecting rod journal for taper. Technician B uses a micrometer to measure the connecting rod journal for out-of-roundness. Who is correct?
- Technician A
Expert Solution & Answer
Trending nowThis is a popular solution!
Students have asked these similar questions
Technician A uses a micrometer to measure the connectingrod journal for taper. Technician B uses amicrometer to measure the connecting rod journalfor out-of-roundness. Who is correct?a. Technician Ab. Technician Bc. Both A and Bd. Neither A nor B
What tool is generally used to measure crank shaft bearing journals?
a. vernier calipers
b. micrometer
c. straightedge and a feeler gauge
d. telescopic gauge and micrometer
True or False? The largest diameter threaded rod is available only up-to 8-inches.
Chapter 11 Solutions
Automotive Technology: A Systems Approach (MindTap Course List)
Ch. 11 - Explain how to use a micrometer to measure cam...Ch. 11 - What is the cylinder taper?Ch. 11 - Describe how to measure main bearing oil...Ch. 11 - Where does maximum cylinder bore wear occur and...Ch. 11 - What type of valve lifter automatically...Ch. 11 - List three types of compression rings.Ch. 11 - Most pistons used today are made of. cast iron...Ch. 11 - Cam bearings in OHV engines are typically which...Ch. 11 - Which of the following is not of concern when...Ch. 11 - True or False? Cylinder taper is the difference in...
Ch. 11 - What is the purpose of a thrust main bearing?Ch. 11 - Each halt' of a split bearing is made slightly...Ch. 11 - Prob. 13RQCh. 11 - Prob. 14RQCh. 11 - Which type of oil ring is slotted so that excess...Ch. 11 - When removing the balance shaft assembly:...Ch. 11 - After installing cam bearings: Technician A checks...Ch. 11 - Technician A says that a cylinder wall with too...Ch. 11 - Technician A uses a pry bar to stretch the timing...Ch. 11 - Technician A installs a cup-type core plug with...Ch. 11 - Technician A uses a micrometer to measure the...Ch. 11 - Technician A says that piston ring end gaps should...Ch. 11 - Technician A checks crankshaft oil clearance with...Ch. 11 - When removing the piston and rod assemblies from a...Ch. 11 - Technician A says that crankshaft counterweights...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- Technician A says that shims may be used to adjust shaft end play. Technician B says that snap rings may be used to adjust shaft end play. Who is correct? a. Technician A only b. Technician B only c. Both A and B d. Neither A nor Barrow_forwardTechnician A uses a pry bar to stretch the timing chain onto its sprockets. Technician B cools the timing sprockets so that the timing chain will slip over the teeth. Who is correct? Technician A Technician B Both A and B Neither A nor Barrow_forwardChoose the correct device pair from the following which is a common example for lower pair and self-closed pair. a. Roller and rings of bearing. b. Cam and follower. c. Gear mesh with another gear. d. Nut and bolt.arrow_forward
- While discussing proper band adjustment procedures: Technician A says that on some vehicles the bands can be adjusted externally with a torque wrench. Technician B says that a calibrated inch- pound torque wrench is normally used to tighten the band adjusting bolt to a specified torque. Who is correct? a. Technician A only b. Technician B only c. Both A and B d. Neither A nor Barrow_forwardWhile diagnosing the cause of a clicking noise that is heard only when the car is turning: Technician A says that the most probable cause is a worn wheel bearing. Technician B says that the most probable cause is a worn outboard CV joint. Who is correct? a. Technician A only b. Technician B only c. Both A and B d. Neither A nor Barrow_forwardRadial and axial tolerances in the ball joints are checked using a _____. a. beam-type torque wrench b. dial caliper c. straightedge d. dial indicatorarrow_forward
- It is a wrench that has a movable jaw which makes it adjustable to various sizes of nuts [(a Double ended wrench (b)adjustable wrench (c) plier (d) combination wrencharrow_forwardIdentify the part not belonging to micrometer. Frame Ratchet Locknut Clamparrow_forwardWhich of the following is the most likely cause for a shudder during the engagement of a lock-up torque converter? a. A bad converter b. Worn or damaged CV or U-joints c. A worn front planetary gearset d. Loose flexplatearrow_forward
- While diagnosing the cause of noise from a transfer case: Technician A says that a probable cause is incorrect tire size. Technician B says that the most probable cause is a faulty bearing or gear. Who is correct? a. Technician A only b. Technician B only c. Both A and B d. Neither A nor Barrow_forwardWhile inspecting the timing gears of an engine: Technician A says a gear with cracks, spalling, or excessive wear on the tooth surface indicates improper gear backlash. Technician B says the diameter of many of the engines timing gears and sprockets should be measured with the drive chain wrapped around the individual gears. Who is correct? Technician A Technician B Both A and B Neither A nor Barrow_forward6 During drilling operation, work piece must be held in vice. Select one: True Falsearrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Automotive Technology: A Systems Approach (MindTa...Mechanical EngineeringISBN:9781133612315Author:Jack Erjavec, Rob ThompsonPublisher:Cengage Learning
Automotive TechnologyMechanical EngineeringISBN:9781337794213Author:ERJAVEC, Jack.Publisher:Cengage,
Automotive Technology: A Systems Approach (MindTa...
Mechanical Engineering
ISBN:9781133612315
Author:Jack Erjavec, Rob Thompson
Publisher:Cengage Learning
Automotive Technology
Mechanical Engineering
ISBN:9781337794213
Author:ERJAVEC, Jack.
Publisher:Cengage,
Mod-01 Lec-16 Basics of Instrumentation; Author: nptelhrd;https://www.youtube.com/watch?v=qbKnW42ZM5c;License: Standard YouTube License, CC-BY