Automotive Technology
7th Edition
ISBN: 9781337794213
Author: ERJAVEC, Jack.
Publisher: Cengage,
expand_more
expand_more
format_list_bulleted
Videos
Textbook Question
Chapter 11, Problem 7SA
How should the oil pump be primed when installing it into the engine?
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
What happens to the engine due to high temperature ?
what is tappet clearance and how it can be maintained to run the engine smoothly
Which of the following is a function of the engine’slubrication system?a. Holds an adequate supply of oilb. Removes contaminants from the oilc. Delivers oil to all necessary areas of the engined. All of the above
Chapter 11 Solutions
Automotive Technology
Ch. 11 - Describe how to inspect an oil pump.Ch. 11 - What is the cylinder taper?Ch. 11 - Describe how to measure main bearing oil...Ch. 11 - Where does maximum cylinder bore wear occur and...Ch. 11 - List three types of compression rings.Ch. 11 - What is the purpose of a thrust main bearing?Ch. 11 - How should the oil pump be primed when installing...Ch. 11 - Most pistons used today are made of. cast iron...Ch. 11 - Cam bearings in OHV engines are typically which...Ch. 11 - Which of the following is not of concern when...
Ch. 11 - Each halt' of a split bearing is made slightly...Ch. 11 - Prob. 5MCCh. 11 - Which of the following are not typically found in...Ch. 11 - All of the following are functions of the...Ch. 11 - Which type of oil ring is slotted so that excess...Ch. 11 - When removing the balance shaft assembly:...Ch. 11 - After installing cam bearings: Technician A checks...Ch. 11 - Technician A says that a cylinder wall with too...Ch. 11 - Technician A installs a cup-type core plug with...Ch. 11 - Technician A uses a micrometer to measure the...Ch. 11 - Technician A says that piston ring end gaps should...Ch. 11 - Technician A checks crankshaft oil clearance with...Ch. 11 - When removing the piston and rod assemblies from a...Ch. 11 - Technician A says that crankshaft counterweights...Ch. 11 - Technician A uses a feeler gauge and straightedge...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- Why must hydraulic line pressures increase when there is an increase of load on the engine?arrow_forwardTrue or False? The first step in removing an engine is usually the removal of the intake and exhaust manifolds.arrow_forwardWhich of the following is a function of the engines lubrication system? Holds an adequate supply of oil Removes contaminants from the oil Delivers oil to all necessary areas of the engine All of the abovearrow_forward
- What are the advantages and disadvantages of the engine lubrication system?arrow_forwardCarbon deposits on the intake valve or seat may cause the valve not to close properly. Tech a says that the flywheel will be harder to spin when starting the engine. Tech b says that the engine will loose power. Who is correct?arrow_forwardWhat checks can be performed to know if the lubricating oil of an engine has been contaminated?arrow_forward
- Which of the following are not typically found in the block of a modern engine? a. Pistons b. Crankshaft c. Valves d. Oil pumparrow_forwardTrue or False? The camshaft is always locatedin the engine block.arrow_forwardwhat are the two tune up methods used for a variety of big bore cummins enginesarrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Automotive TechnologyMechanical EngineeringISBN:9781337794213Author:ERJAVEC, Jack.Publisher:Cengage,
Automotive Technology: A Systems Approach (MindTa...Mechanical EngineeringISBN:9781133612315Author:Jack Erjavec, Rob ThompsonPublisher:Cengage Learning
Refrigeration and Air Conditioning Technology (Mi...Mechanical EngineeringISBN:9781305578296Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill JohnsonPublisher:Cengage Learning 
Welding: Principles and Applications (MindTap Cou...Mechanical EngineeringISBN:9781305494695Author:Larry JeffusPublisher:Cengage Learning
Automotive Technology
Mechanical Engineering
ISBN:9781337794213
Author:ERJAVEC, Jack.
Publisher:Cengage,
Automotive Technology: A Systems Approach (MindTa...
Mechanical Engineering
ISBN:9781133612315
Author:Jack Erjavec, Rob Thompson
Publisher:Cengage Learning
Refrigeration and Air Conditioning Technology (Mi...
Mechanical Engineering
ISBN:9781305578296
Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson
Publisher:Cengage Learning
Welding: Principles and Applications (MindTap Cou...
Mechanical Engineering
ISBN:9781305494695
Author:Larry Jeffus
Publisher:Cengage Learning
The Refrigeration Cycle Explained - The Four Major Components; Author: HVAC Know It All;https://www.youtube.com/watch?v=zfciSvOZDUY;License: Standard YouTube License, CC-BY