Automotive Technology: A Systems Approach (MindTap Course List)
6th Edition
ISBN: 9781133612315
Author: Jack Erjavec, Rob Thompson
Publisher: Cengage Learning
expand_more
expand_more
format_list_bulleted
Textbook Question
Chapter 12, Problem 10ASRQ
While servicing a pair of aluminum cylinder heads: Technician A says it' needed, both heads must be machined equally and the same amount of material removed from each. Technician B replaces both heads if the warpage exceeds the specified allowable amount Who is correct?
- Technician A
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solutionStudents have asked these similar questions
The shaft in the front wheel of bike is_____.A.Shafts in bending and torsion
B.Shafts in bending only
C.Shafts in torsion mainly
#3 vibration, will upvote anyone who will answers thanks.
Complete solution and correct units pls
If the service information does not provide a loosening sequence for the cylinder head bolts, what should you do?
Chapter 12 Solutions
Automotive Technology: A Systems Approach (MindTap Course List)
Ch. 12 - Explain staged and continuously variable value...Ch. 12 - Define valve margin.Ch. 12 - What usually causes warpage in an aluminum cylin...Ch. 12 - What are the two ways pushrods can be checked for...Ch. 12 - Which of the following is not true of knurling? It...Ch. 12 - True False? Fiats MultiAir system relies on...Ch. 12 - To allow the engine to run on the Atkinson cycle,...Ch. 12 - Prob. 8RQCh. 12 - To ensure proper seating of the valve, the valve...Ch. 12 - When checking valve fit, contact between the valve...
Ch. 12 - If the valve face and valve seat do not contact...Ch. 12 - Many engines with WT have a phaser mounted to the...Ch. 12 - Multiple valve engines tend to be more efficient...Ch. 12 - Which of the following is not a type of valve...Ch. 12 - Which of the following statements is not true?...Ch. 12 - While discussing the reasons for resurfacing a...Ch. 12 - While inspecting the timing gears of an engine:...Ch. 12 - Technician A says that positive valve stem seals...Ch. 12 - When fitting a freshly ground valve into a freshly...Ch. 12 - Technician A says off-square springs may cause...Ch. 12 - Technician A says it is not necessary to measure...Ch. 12 - Technician A uses a 30-degree stone for topping a...Ch. 12 - While discussing the Valvetronic system:...Ch. 12 - While checking a hydraulic phaser after the...Ch. 12 - While servicing a pair of aluminum cylinder heads:...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- When machining brake drums: Technician A tries to remove only enough metal to obtain a true, smooth surface. Technician B cuts the drum on the other side of the axle to the same diameter as the one that was cut first. Who is correct? Technician A only Technician B only Both A and B Neither A nor Barrow_forwardWhat usually causes warpage in an aluminum cylin der head?arrow_forwardWhen removing the piston and rod assemblies from a cylinder block; Technician A positions the throw of the crankshaft at the top of its stroke and removes the connecting rod nuts and cap. Technician B covers the rod bolts with protectors and pushes the piston and rod assembly out with the wooden hammer handle or wooden drift and supports the piston as it comes out of the cylinder. Who is correct? Technician A Technician B Both A and B Neither A nor Barrow_forward
- While discussing thread sealants and lubricants: Technician A says that antiseize compound is used where a bolt might become difficult to remove after a period of time. Technician B says that thread sealants are used on bolts that are tightened into an oil cavity or coolant passage. Who is correct? Technician A Technician B Both A and B Neither A nor Barrow_forwardTechnician A uses a punch to align holes in parts during assembly. Technician B uses a chisel to drive out rivets. Who is correct? Technician A Technician B Both A and B Neither A nor Barrow_forwardMaterials that can be used as housing for the Wedge belt Drivearrow_forward
- Technician A says that flare nut or line wrenches should be sued to loosen or tighten brake line or tubing fittings Technician B says that open-end wrenches will surround the fitting's nut and provide a positive grip on the fitting. Who is correct? Group of answer choices Technician A only Technician B only Both Technicians A and B Neither A nor Barrow_forwardA tool make easy work of removing broken threaded ends of pipe, plugs & fittings. A tool make easy work of removing broken threaded ends of pipe, plugs & fittings. Pipe Reamer Pipe Vise Pipe Extractor Flaring tool Pipe taparrow_forwardExcessive drive roller pressure causes what problems?arrow_forward
- How does a torque-to-yield bolt differ from standard bolts?arrow_forwardWhen servicing transfer cases, all of the following are correct, except_____. a. it must be supported on a transmission jack or safety stands b. the chain drive and a planetary gearset must be adjusted to specifications c. visual inspections for leaks and damage are necessary d. follow the manufacturers recommendations for lubricantsarrow_forwardCan be manufactured by cast aluminum alloy only. a. Nose Section b. Power Section c. Supercharger section d. Accessory Section e. All of the above The rollers and balls used in some bearings are made of polished steel. a. True b. Falsearrow_forward
arrow_back_ios
arrow_forward_ios
Recommended textbooks for you
- Automotive Technology: A Systems Approach (MindTa...Mechanical EngineeringISBN:9781133612315Author:Jack Erjavec, Rob ThompsonPublisher:Cengage LearningWelding: Principles and Applications (MindTap Cou...Mechanical EngineeringISBN:9781305494695Author:Larry JeffusPublisher:Cengage Learning
Automotive Technology: A Systems Approach (MindTa...
Mechanical Engineering
ISBN:9781133612315
Author:Jack Erjavec, Rob Thompson
Publisher:Cengage Learning
Welding: Principles and Applications (MindTap Cou...
Mechanical Engineering
ISBN:9781305494695
Author:Larry Jeffus
Publisher:Cengage Learning
HOME SHOP JIGS & FIXTURES PART 1, TYPES OF JIGS & ACCESSORIES AND THE THEORIE BEHIND THE TOOLS; Author: THATLAZYMACHINIST;https://www.youtube.com/watch?v=EXYqi42JimI;License: Standard Youtube License