MECHANICS OF MATERIAL (LL)
MECHANICS OF MATERIAL (LL)
7th Edition
ISBN: 9781260663822
Author: BEER
Publisher: MCG
bartleby

Videos

Textbook Question
Chapter 1.2, Problem 25P

Knowing that θ = 40° and P = 9 kN, determine (a) the smallest allowable diameter of the pin at B if the average shearing stress in the pin is not to exceed 120 MPa, (b) the corresponding average bearing stress in member AB at B, (c) the corresponding average bearing stress in each of the support brackets at B.

Fig. P1.24 and P1.25

Chapter 1.2, Problem 25P, Knowing that  = 40 and P = 9 kN, determine (a) the smallest allowable diameter of the pin at B if

Blurred answer
Students have asked these similar questions
Two steel plates are to be held together by means of 16-mm-diameter high-strength steel bolts fitting snugly inside cylindrical brass spacers. Knowing that the average normal stress must not exceed 205 MPa in the bolts and 132 MPa in the spacers, determine the outer diameter of the spacers that yields the most economical and safe design.    The outer diameter of the spacers that yields the most economical and safe design is  mm.
Two links BF are made of steel with a 450-MPa ultimate normal stress and has a 6x12–mm uniform rectangular cross section. Links BF are connected to members ABD and CDEF by 8-mm diameter pins; ABD and CDEF are connected together by a 10-mm diameter pin; CDEF is connected to the support by a 10-mm diameter pin; all of the pins are made of steel with a 170 MPa ultimate shearing stress. Knowing that a factor of safety of 3 is desired, determine the largest load P that may be applied
Two wooden planks, each 1212 in. thick and 9 in. wide, are joined by the dry mortise joint shown. Knowing that the wood used shears off along its grain when the average shearing stress reaches 1.8 ksi, determine the magnitude P of the axial load that will cause the joint to fail.    The magnitude P of the axial load that will cause the joint to fail is  kips.

Chapter 1 Solutions

MECHANICS OF MATERIAL (LL)

Ch. 1.2 - For the Pratt bridge truss and loading shown,...Ch. 1.2 - The frame shown consists of four wooden members,...Ch. 1.2 - An aircraft tow bar is positioned by means of a...Ch. 1.2 - Two hydraulic cylinders are used to control the...Ch. 1.2 - Determine the diameter of the largest circular...Ch. 1.2 - Two wooden planks, each 12 in. thick and 9 in....Ch. 1.2 - When the force P reached 1600 lb, the wooden...Ch. 1.2 - A load P is applied to a steel rod supported as...Ch. 1.2 - The axial force in the column supporting the...Ch. 1.2 - Three wooden planks are fastened together by a...Ch. 1.2 - A 40-kN axial load is applied to a short wooden...Ch. 1.2 - An axial load P is supported by a short W8 40...Ch. 1.2 - Link AB, of width b = 2 in. and thickness t=14...Ch. 1.2 - Determine the largest load P that can be applied...Ch. 1.2 - Knowing that = 40 and P = 9 kN, determine (a) the...Ch. 1.2 - The hydraulic cylinder CF, which partially...Ch. 1.2 - For the assembly and loading of Prob. 1.7,...Ch. 1.2 - Two identical linkage-and-hydraulic-cylinder...Ch. 1.5 - Two wooden members of uniform rectangular cross...Ch. 1.5 - Two wooden members of uniform rectangular cross...Ch. 1.5 - The 1.4-kip load P is supported by two wooden...Ch. 1.5 - Two wooden members of uniform cross section are...Ch. 1.5 - A centric load P is applied to the granite block...Ch. 1.5 - A 240-kip load P is applied to the granite block...Ch. 1.5 - A steel pipe of 400-mm outer diameter is...Ch. 1.5 - A steel pipe of 400-mm outer diameter is...Ch. 1.5 - A steel loop ABCD of length 5 ft and of 38-in....Ch. 1.5 - Link BC is 6 mm thick, has a width w = 25 mm, and...Ch. 1.5 - Link BC is 6 mm thick and is made of a steel with...Ch. 1.5 - Members AB and BC of the truss shown are made of...Ch. 1.5 - Members AB and BC of the truss shown are made of...Ch. 1.5 - Link AB is to be made of a steel for which the...Ch. 1.5 - Two wooden members are joined by plywood splice...Ch. 1.5 - For the joint and loading of Prob. 1.43, determine...Ch. 1.5 - Three 34-in.-diameter steel bolts are to be used...Ch. 1.5 - Three steel bolts are to be used to attach the...Ch. 1.5 - A load P is supported as shown by a steel pin that...Ch. 1.5 - A load P is supported as shown by a steel pin that...Ch. 1.5 - A steel plate 14 in. thick is embedded in a...Ch. 1.5 - Determine the factor of safety for the cable...Ch. 1.5 - Link AC is made of a steel with a 65-ksi ultimate...Ch. 1.5 - Solve Prob. 1.51, assuming that the structure has...Ch. 1.5 - Each of the two vertical links CF connecting the...Ch. 1.5 - Solve Prob. 1.53, assuming that the pins at C and...Ch. 1.5 - In the structure shown, an 8-mm-diameter pin is...Ch. 1.5 - In an alternative design for the structure of...Ch. 1.5 - Prob. 57PCh. 1.5 - The Load and Resistance Factor Design method is to...Ch. 1 - In the marine crane shown, link CD is known to...Ch. 1 - Two horizontal 5-kip forces are applied to pin B...Ch. 1 - For the assembly and loading of Prob. 1.60,...Ch. 1 - Two steel plates are to be held together by means...Ch. 1 - A couple M of magnitude 1500 N m is applied to...Ch. 1 - Knowing that link DE is 18 in. thick and 1 in....Ch. 1 - A 58-in.-diameter steel rod AB is fitted to a...Ch. 1 - In the steel structure shown, a 6-mm-diameter pin...Ch. 1 - Prob. 67RPCh. 1 - A force P is applied as shown to a steel...Ch. 1 - The two portions of member AB are glued together...Ch. 1 - The two portions of member AB are glued together...

Additional Engineering Textbook Solutions

Find more solutions based on key concepts
Knowledge Booster
Mechanical Engineering
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.
Similar questions
    • SEE MORE QUESTIONS
    Recommended textbooks for you
  • Elements Of Electromagnetics
    Mechanical Engineering
    ISBN:9780190698614
    Author:Sadiku, Matthew N. O.
    Publisher:Oxford University Press
    Mechanics of Materials (10th Edition)
    Mechanical Engineering
    ISBN:9780134319650
    Author:Russell C. Hibbeler
    Publisher:PEARSON
    Thermodynamics: An Engineering Approach
    Mechanical Engineering
    ISBN:9781259822674
    Author:Yunus A. Cengel Dr., Michael A. Boles
    Publisher:McGraw-Hill Education
  • Control Systems Engineering
    Mechanical Engineering
    ISBN:9781118170519
    Author:Norman S. Nise
    Publisher:WILEY
    Mechanics of Materials (MindTap Course List)
    Mechanical Engineering
    ISBN:9781337093347
    Author:Barry J. Goodno, James M. Gere
    Publisher:Cengage Learning
    Engineering Mechanics: Statics
    Mechanical Engineering
    ISBN:9781118807330
    Author:James L. Meriam, L. G. Kraige, J. N. Bolton
    Publisher:WILEY
  • Elements Of Electromagnetics
    Mechanical Engineering
    ISBN:9780190698614
    Author:Sadiku, Matthew N. O.
    Publisher:Oxford University Press
    Mechanics of Materials (10th Edition)
    Mechanical Engineering
    ISBN:9780134319650
    Author:Russell C. Hibbeler
    Publisher:PEARSON
    Thermodynamics: An Engineering Approach
    Mechanical Engineering
    ISBN:9781259822674
    Author:Yunus A. Cengel Dr., Michael A. Boles
    Publisher:McGraw-Hill Education
    Control Systems Engineering
    Mechanical Engineering
    ISBN:9781118170519
    Author:Norman S. Nise
    Publisher:WILEY
    Mechanics of Materials (MindTap Course List)
    Mechanical Engineering
    ISBN:9781337093347
    Author:Barry J. Goodno, James M. Gere
    Publisher:Cengage Learning
    Engineering Mechanics: Statics
    Mechanical Engineering
    ISBN:9781118807330
    Author:James L. Meriam, L. G. Kraige, J. N. Bolton
    Publisher:WILEY
    BEARINGS BASICS and Bearing Life for Mechanical Design in 10 Minutes!; Author: Less Boring Lectures;https://www.youtube.com/watch?v=aU4CVZo3wgk;License: Standard Youtube License