Automotive Technology: A Systems Approach (MindTap Course List)
6th Edition
ISBN: 9781133612315
Author: Jack Erjavec, Rob Thompson
Publisher: Cengage Learning
expand_more
expand_more
format_list_bulleted
Concept explainers
Videos
Textbook Question
Chapter 12, Problem 2ASRQ
While inspecting the timing gears of an engine: Technician A says a gear with cracks, spalling, or excessive wear on the tooth surface indicates improper gear backlash. Technician B says the diameter of many of the engines timing gears and sprockets should be measured with the drive chain wrapped around the individual gears. Who is correct?
- Technician A
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
While inspecting a planetary gear-type final drive, Technician A says blackened pinion shafts indicate severe overloading. Technician B says bluish gears indicate overheating. Who is correct?
Technician A says that a Simpson gearset is two planetary gearsets that share
a common sun gear. Technician B says that a Ravigneaux gearset has two
sun gears, two sets of planet gears, and a common ring gear. Who is
correct?
a.Technician A only
b.Technician B only
c.Both A and B
d.Neither A or B
Gears and crankshaft are transmitting type of short distance power type of transmission.
Select one:
True
False
Chapter 12 Solutions
Automotive Technology: A Systems Approach (MindTap Course List)
Ch. 12 - Explain staged and continuously variable value...Ch. 12 - Define valve margin.Ch. 12 - What usually causes warpage in an aluminum cylin...Ch. 12 - What are the two ways pushrods can be checked for...Ch. 12 - Which of the following is not true of knurling? It...Ch. 12 - True False? Fiats MultiAir system relies on...Ch. 12 - To allow the engine to run on the Atkinson cycle,...Ch. 12 - Prob. 8RQCh. 12 - To ensure proper seating of the valve, the valve...Ch. 12 - When checking valve fit, contact between the valve...
Ch. 12 - If the valve face and valve seat do not contact...Ch. 12 - Many engines with WT have a phaser mounted to the...Ch. 12 - Multiple valve engines tend to be more efficient...Ch. 12 - Which of the following is not a type of valve...Ch. 12 - Which of the following statements is not true?...Ch. 12 - While discussing the reasons for resurfacing a...Ch. 12 - While inspecting the timing gears of an engine:...Ch. 12 - Technician A says that positive valve stem seals...Ch. 12 - When fitting a freshly ground valve into a freshly...Ch. 12 - Technician A says off-square springs may cause...Ch. 12 - Technician A says it is not necessary to measure...Ch. 12 - Technician A uses a 30-degree stone for topping a...Ch. 12 - While discussing the Valvetronic system:...Ch. 12 - While checking a hydraulic phaser after the...Ch. 12 - While servicing a pair of aluminum cylinder heads:...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- While discussing a pressure test: Technician A says that this test is the most valuable diagnostic check for slippage when a gear is engaged. Technician B says that the test can identify the cause of late or harsh shifting. Who is correct? a. Technician A only b. Technician B only c. Both A and B d. Neither A nor Barrow_forwardWhile inspecting a transaxies gears: Technician A says that wear on the back of the gear teeth is normal. Technician B says that it is normal for a reverse idler gear to have small chips on its engagement side. Who is correct? a. Technician A only b. Technician B only c. Both A and B d. Neither A nor Barrow_forwardWhile discussing ways to determine if a pilot bushing is faulty: Technician A says that if it operated quietly, it does not need to be replaced. Technician B says that a careful inspection of the transmissions input shaft can determine the condition of the pilot bushing. Who is correct? a. Technician A only b. Technician B only c. Both A and B d. Neither A nor Barrow_forward
- Technician A says that a prerequisite to accurate road-testing analysis is knowing what planetary controls are applied in a particular gear range. Technician B says that all slipping conditions can be traced to a leaking hydraulic circuit. Who is correct? a. Technician A only b. Technician B only c. Both A and B d. Neither A nor Barrow_forwardTechnician A says that a gear tooth pattern identifies ring gear runout. Technician B says that gear patterns are not accurate if there is excessive ring gear runout. Who is correct? a. Technician A only b. Technician B only c. Both A and B d. Neither A nor Barrow_forwardUsing a lubricant that is thicker than the specified lubricant can lead to_____. a. the gear to jump out b. hard shifting c. gear lockup d. gear slippagearrow_forward
- While diagnosing the cause of noise from a transfer case: Technician A says that a probable cause is incorrect tire size. Technician B says that the most probable cause is a faulty bearing or gear. Who is correct? a. Technician A only b. Technician B only c. Both A and B d. Neither A nor Barrow_forwardAfter installing cam bearings: Technician A checks that the oi, holes in the bearings are properly aligned with those in the block by squirting oil into the holes. Technician B checks for proper alignment by inserting a wire through the holes. Who is correct? Technician A Technician B Both A and B Neither A nor Barrow_forwardTrue or False? A set of gears can be configured or used in three different ways.arrow_forward
- Technician A says off-square springs may cause increased stem-to-guide wear. Technician B says excessive spring tension may cause premature camshaft wear. Who is correct? Technician A Technician B Both A and B Neither A nor Barrow_forwardTechnician A says that in a conventional transmission, the speed gears freewheel around the mainshaft until they are locked to it by the appropriate synchronizer. Technician B says that speed gears are an integral part of the countershaft assembly. Who is correct? a. Technician A only b. Technician B only c. Both A and B d. Neither A nor Barrow_forwardPinion gear-to-flywheel ring gear clearance is being discussed: Technician A says that if there is too much clearance, there will be a high pitch while the engine cranks. Technician B says that if there is too little clearance, there will be a high pitch noise after the engine is started. Who is correct? Technician A Technician B Both A and B Neither A nor Barrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Automotive Technology: A Systems Approach (MindTa...Mechanical EngineeringISBN:9781133612315Author:Jack Erjavec, Rob ThompsonPublisher:Cengage Learning
Automotive TechnologyMechanical EngineeringISBN:9781337794213Author:ERJAVEC, Jack.Publisher:Cengage,
Automotive Technology: A Systems Approach (MindTa...
Mechanical Engineering
ISBN:9781133612315
Author:Jack Erjavec, Rob Thompson
Publisher:Cengage Learning
Automotive Technology
Mechanical Engineering
ISBN:9781337794213
Author:ERJAVEC, Jack.
Publisher:Cengage,
Power Transmission; Author: Terry Brown Mechanical Engineering;https://www.youtube.com/watch?v=YVm4LNVp1vA;License: Standard Youtube License