Physics for Scientists and Engineers
Physics for Scientists and Engineers
10th Edition
ISBN: 9781337553278
Author: Raymond A. Serway, John W. Jewett
Publisher: Cengage Learning
bartleby

Concept explainers

bartleby

Videos

Textbook Question
Chapter 12, Problem 36AP

Why is the following situation impossible? A worker in a factory pulls a cabinet across the floor using a rope as shown in Figure P12.36a. The rope make an angle θ = 37.0° with the floor and is tied h1 = 10.0 cm from the bottom of the cabinet. The uniform rectangular cabinet has height = 100 cm and width w = 60.0 cm, and it weighs 400 N. The cabinet slides with constant speed when a force F = 300 N is applied through the rope. The worker tires of walking backward. He fastens the rope to a point on the cabinet h2 = 65.0 cm off the floor and lays the rope over his shoulder so that he can walk forward and pull as shown in Figure P12.36b. In this way, the rope again makes an angle of θ = 37.0° with the horizontal and again has a tension of 300 N. Using this technique, the worker is able to slide the cabinet over a long distance on the floor without tiring.

Figure P12.36 Problems 36 and 44.

Chapter 12, Problem 36AP, Why is the following situation impossible? A worker in a factory pulls a cabinet across the floor

Blurred answer
Students have asked these similar questions
A uniform rod is 2.00 m long and has mass 1.80 kg. A 2.40 kg clamp is attached to the rod. How far should the center of gravity of the clamp be from the left-hand end of the rod in order for the center of gravity of the composite object to be 1.20 m from the left-hand end of the rod?
A uniform beam resting on two pivots has a length L = 6.00 m and mass M = 90.0 kg.The pivot under the left end exerts a normal force n1 on the beam, and the secondpivot located a distance ℓ = 4.00 m from the left end exerts a normal force nℓ. A womanof mass m = 55.0 kg steps onto the left end of the beam and begins walking to the rightas in Figure P12.24. The goal is to find the woman’s position when the beam begins totip. (a) What is the appropriate analysis model for the beam before it begins to tip? (b)Sketch a force diagram for the beam, labeling the gravitational and normal forcesacting on the beam and placing the woman a distance x to the right of the first pivot,which is the origin. (c) Where is the woman when the normal force n1is the greatest?(d) What is n1 when the beam is about to tip? (e) Use Equation 12.1 to find the value ofn2 when the beam is about to tip. (f) Using the result of part (d) and Equation 12.2,with torques computed around the second pivot, find the woman’s…
If the new center of gravity of a 14m uniform steel rod with a mass m = 75kg is situated to the left of its geometric center after a 50 kg object is attached to it, determine the point where the object is attached. a. 4.5 m b. 9.5 m c. 8.5 m d. 7.0 m

Chapter 12 Solutions

Physics for Scientists and Engineers

Ch. 12 - Prob. 7PCh. 12 - A uniform beam of length L and mass m shown in...Ch. 12 - A flexible chain weighing 40.0 N hangs between two...Ch. 12 - A 20.0-kg floodlight in a park is supported at the...Ch. 12 - Prob. 11PCh. 12 - Review. While Lost-a-Lot ponders his next move in...Ch. 12 - Figure P12.13 shows a claw hammer being used to...Ch. 12 - A 10.0-kg monkey climbs a uniform ladder with...Ch. 12 - John is pushing his daughter Rachel in a...Ch. 12 - Prob. 16PCh. 12 - The deepest point in the ocean is in the Mariana...Ch. 12 - A steel wire of diameter 1 mm can support a...Ch. 12 - A child slides across a floor in a pair of...Ch. 12 - Evaluate Youngs modulus for the material whose...Ch. 12 - Assume if the shear stress in steel exceeds about...Ch. 12 - When water freezes, it expands by about 9.00%....Ch. 12 - Review. A 30.0-kg hammer, moving with speed 20.0...Ch. 12 - A uniform beam resting on two pivots has a length...Ch. 12 - A bridge of length 50.0 m and mass 8.00 104 kg is...Ch. 12 - Prob. 26APCh. 12 - The lintel of prestressed reinforced concrete in...Ch. 12 - The following equations are obtained from a force...Ch. 12 - A hungry bear weighing 700 N walks out on a beam...Ch. 12 - A 1 200-N uniform boom at = 65 to the vertical is...Ch. 12 - A uniform sign of weight Fg and width 2L hangs...Ch. 12 - When a person stands on tiptoe on one foot (a...Ch. 12 - A 10 000-N shark is supported by a rope attached...Ch. 12 - Assume a person bends forward to lift a load with...Ch. 12 - A uniform beam of mass m is inclined at an angle ...Ch. 12 - Why is the following situation impossible? A...Ch. 12 - When a circus performer performing on the rings...Ch. 12 - Figure P12.38 shows a light truss formed from...Ch. 12 - Prob. 39APCh. 12 - A stepladder of negligible weight is constructed...Ch. 12 - A stepladder of negligible weight is constructed...Ch. 12 - Review. A wire of length L, Youngs modulus Y, and...Ch. 12 - Two racquetballs, each having a mass of 170 g, are...Ch. 12 - Prob. 44APCh. 12 - Review. An aluminum wire is 0.850 m long and has a...Ch. 12 - You have been hired as an expert witness in a case...Ch. 12 - A 500-N uniform rectangular sign 4.00 m wide and...Ch. 12 - A steel cable 3.00 cm2 in cross-sectional area has...Ch. 12 - A uniform rod of weight Fg and length L is...Ch. 12 - In the What If? section of Example 12.2, let d...
Knowledge Booster
Physics
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, physics and related others by exploring similar questions and additional content below.
Similar questions
  • In Figure P10.40, the hanging object has a mass of m1 = 0.420 kg; the sliding block has a mass of m2 = 0.850 kg; and the pulley is a hollow cylinder with a mass of M = 0.350 kg, an inner radius of R1 = 0.020 0 m, and an outer radius of R2 = 0.030 0 m. Assume the mass of the spokes is negligible. The coefficient of kinetic friction between the block and the horizontal surface is k = 0.250. The pulley turns without friction on its axle. The light cord does not stretch and does not slip on the pulley. The block has a velocity of vi = 0.820 m/s toward the pulley when it passes a reference point on the table. (a) Use energy methods to predict its speed after it has moved to a second point, 0.700 m away. (b) Find the angular speed of the pulley at the same moment. Figure P10.40
    A uniform beam resting on two pivots has a length L = 6.00 m and mass M = 90.0 kg. The pivot under the left end exerts a normal force n1 on the beam, and the second pivot located a distance = 4.00 m from the left end exerts a normal force n2. A woman of mass m = 55.0 kg steps onto the left end of the beam and begins walking to the right as in Figure P10.28. The goal is to find the womans position when the beam begins to tip. (a) What is the appropriate analysis model for the beam before it begins to tip? (b) Sketch a force diagram for the beam, labeling the gravitational and normal forces acting on the beam and placing the woman a distance x to the right of the first pivot, which is the origin. (c) Where is the woman when the normal force n1 is the greatest? (d) What is n1 when the beam is about to tip? (e) Use Equation 10.27 to find the value of n2 when the beam is about to tip. (f) Using the result of part (d) and Equation 10.28, with torques computed around the second pivot, find the womans position x when the beam is about to tip. (g) Check the answer to part (e) by computing torques around the first pivot point. Figure P10.28
    A bridge of length 50.0 m and mass 8.00 104 kg is supported on a smooth pier at each end as shown in Figure P12.25. A truck of mass 3.00 104 kg is located 15.0 m from one end. What are the forces on the bridge at the points of support? Figure P12.25
  • A stepladder of negligible weight is constructed as shown in Figure P12.40, with AC = BC = . A painter of mass m stands on the ladder a distance d from the bottom. Assuming the floor is frictionless, find (a) the tension in the horizontal bar DE connecting the two halves of the ladder, (b) the normal forces at A and B, and (c) the components of the reaction force at the single hinge C that the left half of the ladder exerts on the right half. Suggestion: Treat the ladder as a single object, but also treat each half of the ladder separately. Figure P12.40 Problems 40 and 41.
    A 10.0-kg monkey climbs a uniform ladder with weight 1.20 102 N and length L = 3.00 m as shown in Figure P12.14. The ladder rests against the wall and makes an angle of = 60.0 with the ground. The upper and lower ends of the ladder rest on frictionless surfaces. The lower end is connected to the wall by a horizontal rope that is frayed and can support a maximum tension of only 80.0 N. (a) Draw a force diagram for the ladder. (b) Find the normal force exerted on the bottom of the ladder. (c) Find the tension in the rope when the monkey is two-thirds of the way up the ladder. (d) Find the maximum distance d that the monkey can climb up the ladder before the rope breaks. (e) If the horizontal surface were rough and the rope were removed, how would your analysis of the problem change? What other information would you need to answer parts (c) and (d)? Figure P12.14
    A stepladder of negligible weight is constructed as shown in Figure P10.73, with AC = BC = = 4.00 m. A painter of mass m = 70.0 kg stands on the ladder d = 3.00 m from the bottom. Assuming the floor is frictionless, find (a) the tension in the horizontal bar DE connecting the two halves of the ladder, (b) the normal forces at A and B, and (c) the components of the reaction force at the single hinge C that the left half of the ladder exerts on the right half. Suggestion: Treat the ladder as a single object, but also treat each half of the ladder separately.
    Recommended textbooks for you
  • Physics for Scientists and Engineers
    Physics
    ISBN:9781337553278
    Author:Raymond A. Serway, John W. Jewett
    Publisher:Cengage Learning
    Physics for Scientists and Engineers with Modern ...
    Physics
    ISBN:9781337553292
    Author:Raymond A. Serway, John W. Jewett
    Publisher:Cengage Learning
    Principles of Physics: A Calculus-Based Text
    Physics
    ISBN:9781133104261
    Author:Raymond A. Serway, John W. Jewett
    Publisher:Cengage Learning
  • Physics for Scientists and Engineers: Foundations...
    Physics
    ISBN:9781133939146
    Author:Katz, Debora M.
    Publisher:Cengage Learning
  • Physics for Scientists and Engineers
    Physics
    ISBN:9781337553278
    Author:Raymond A. Serway, John W. Jewett
    Publisher:Cengage Learning
    Physics for Scientists and Engineers with Modern ...
    Physics
    ISBN:9781337553292
    Author:Raymond A. Serway, John W. Jewett
    Publisher:Cengage Learning
    Principles of Physics: A Calculus-Based Text
    Physics
    ISBN:9781133104261
    Author:Raymond A. Serway, John W. Jewett
    Publisher:Cengage Learning
    Physics for Scientists and Engineers: Foundations...
    Physics
    ISBN:9781133939146
    Author:Katz, Debora M.
    Publisher:Cengage Learning
    What is Torque? | Physics | Extraclass.com; Author: Extraclass Official;https://www.youtube.com/watch?v=zXxrAJld9mo;License: Standard YouTube License, CC-BY