What are the two ways pushrods can be checked for straightness?

Q: WHAT IS THE TOTAL SIZE CHANGE OF THE AC BAR

A:

Q: Technician A installs a cup-type core plug with its flanged edge outward. Technician B installs a…

A: New core plugs are installed after the servicing of the engine block. There should not be any damage…

Q: It asks what is the width across the flats of the locking bolt head?

A: The width across the flats of the locking bolt head is 0.5625

Q: Why is high voltage needed to establish a spark across the gap of a spark plug

A: The air-fuel mixture is ignited inside the combustion chamber with the help of spark generated by…

Q: Which of the following is not part of the starter motorcircuit?a. Batteryb. Starting safety switchc.…

A: given; Which of the following is not part of the starter motor circuit?

Q: le for the key to fail in an overload condition rather than more costly

A: While designing a shaft it is always use to design key weekend . Because in case of failure less…

Q: 1750 rpm motor has a 3” pitch diameter drive pulley. It is driving a 9” pitch diameter pulley. What…

A: GivenSpeed of driver pulley ω1=1750rpmdia=3''dia of driving pulley=9''

Q: What is free gyro?

A: Angular velocity is defined as the change in the angular position of a body following circular…

Q: Draw the Circuit diagram for holding the cylinder of double acting cylinder in the fully extended…

A: Directional control valves follow or perform only three functions: 1) Stop Fluid Flow 2) Change the…

Q: What does a slope in the spark line represent?

A: Sparklines are very small line graphs that are usually drawn without axes or coordinates. In a…

Q: Which of the following is not part of the starter motor circuit?

A: The  starting system or starter motor circuit used to give initial rotation or crank to the engine…

Q: How to calculate torque (clockwise and counter-clockwise when three forces are being considered?

A: Solution: Consider three forces are acting on a shaft in clockwise and anti-clockwise directions.…

Q: 4. Describe two type of starting system principles and draw the basic starting circuit

A: The starting system is a combination of mechanical and electrical parts that work together to start…

Q: Industrial Maint. What are the three types of loads that may be placed on a bearing?

A: The three types of loads that may be placed on a bearing are

Q: what happen to the exciter coil as the flywheel rotates past it?

A: Exciter Coil- The very main purpose of this is used to give a stationary rotating magnetic field. It…

Q: of gea

A: given: write four type of gear?

Q: I how such a bolt most likely to fail, will it fail ir

A:

Q: Q1.With a neat diagram ,explain about the working of Flash Type  ADC

A: Flash Type ADC is based on the principle of comparing analog input voltage with a set of…

Q: 4. Describe the sequence of events that occur as the manually operated directional control valve in…

A: 4.     A sequence valve is a pressure valve that opens when the predetermined pressure is…

Q: State and draw two methods used to mount cylinders?

A:

Q: What is the most common control cable used (size)?

A: generally the most commonly used are 7x7 and 7x19 cables.

Q: What is an attenuator used for?

A:

Q: At what RPM is the driven pulley in the belt drive system shown rotating? Driver Pulley 6 Inch Dia…

A:

Q: e Taylor's principle with Plug and Ring Gauge with figure.

A: The given problem is based on metrology.    Taylor's Principles: Go gauge should be design on…

Q: How to creat Drive Shaft in (Siemens) SINUMERIK

A: A drive shaft is a vehicle shaft that transmits power from the transmission to the wheels. The…

Q: failure Mode why bellows corrosion.cause of corosion bellows and their solutions

A: Given Bellow To find Cause of corrosion Solution to corrosion

Q: How to perform zero point reset

A: Zero point reset is an introducing system for tenant discovery sensor that should be performed…

Q: pls do make an ntroduction about  Automatic Return of a Double  Acting Cylinder using Roller Lever…

A: DOUBLE ACTING CYLINDER A double acting cylinder is a chamber wherein the functioning liquid…

Q: orrect

A: GIVEN:

Q: a DCV, this part moves the spool, it can be a lever or a button a. operator b. springs c. spool…

A: The solution is attached below:

Q: Technician A says a bolt may become fatigued if it is over tightened. Technician B says that a bolt…

A: The bolt will be fatigued in both the overtighten and under-tightening cases

Q: How can shift feel be controlled?

A: For many years, accumulators and associated circuits have been the dominant way for regulating…

Q: number of pe f the pinion

A:

Q: (i) which has the greater power output? (ii) which has the higher efficiency?

A:

Q: What is the lowest acceptable amperage setting for GTAwelding?

A: Gas tungsten arc welding (GTAW), also known as tungsten inert gas (TIG) welding, is an arc welding…

Q: How many 14" strips can be cut from a coil 132' long?

A: Given : Strips  space 14'' = 14÷12 = 1.1667 inch  Length of  coil = 132 inch     To find : Number =…

Q: What type of Bolt is the following image?

A: According to the figure, Flange Bolt is showing in the above picture.

Q: What is the alternator to engine drive ratio if alternator turns 1225 rpm when engine is idling at…

A: Since the ratio is 1225 rpm for the alternator: 700 rpm for the engine, 1225: 700         Divide…

Q: Which of the following is not a base Sl unit?

A: Explanation 27 As we know that there are only seven fundamental unit which can we written as 1.…

Q: When the starter spins but does not crank the engine,which of the following may be true?a. Defective…

A: Given Starting problem To find Identify the main problem

Q: Which of the following is NOT a spring type used in pressure plate assemblies?

A: Diaphragm is not a spring type used in pressure plate assemblies.

Q: The surface of the pressure plate contacts?

A: According to Laymen’s terms, the pressure plate is like a clamp with spring-loaded that is attached…

Q: Which of the following wrenches is the best choice fortorquing a bolt?a. Open-endb. Box-endc.…

A: When it comes to bolted joints, orquing is the most popular method of achieving fastener preload.…

Q: Explain the Interruption Cycle with neat sketch

A: The Interruption cycle (also known as the fetch–decode–execute cycle) is the cycle that the…

Q: Find the required number of active coils.

A:

Q: What is the overall height of Tailstock?

A: To Find the overall height of Tailstock?

Q: when checking or setting the backlash it is important to have the dial indicator tip in the correct…

A: The manufacturing of gears is a callous process in terms of accuracy. If the gear is manufactured…

Q: Worn armature bearings can result in higher than normal starter cranking current draw?

A: Moderate cranking and high current draw regularly demonstrate worn bearings or bushings inside…