Automotive Technology: A Systems Approach (MindTap Course List)
6th Edition
ISBN: 9781133612315
Author: Jack Erjavec, Rob Thompson
Publisher: Cengage Learning
expand_more
expand_more
format_list_bulleted
Concept explainers
Textbook Question
Chapter 13, Problem 4ASRQ
Technician A inspects all sealing surfaces for damage and uses a supplementary sealant on the gaskets if the surface is questionable. Technician B coats the intake gasket on some engines with a nonhardening sealer. Who is correct?
- Technician A
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solutionStudents have asked these similar questions
to provide a good sealing joint between the cylinder head and exhaust, apply a sealant to the machined surface
true or false
A compression test gave the following results: cylinder #1 = 155, cylinder #2 = 140, cylinder #3 = 110, cylinder #4 = 105. Technician A says that a defective (burned) valve is the most likely cause. Technician B says that a leaking head gasket could be the cause.
Hydraulic hose couplings do not seal on their connecting threads. They seal on the mating of two surfaces (male & female). What is the common seal angle of these surfaces?
47 degrees
23 degrees
None of these
37 degrees
Varies by tube diameter
Chapter 13 Solutions
Automotive Technology: A Systems Approach (MindTap Course List)
Ch. 13 - True or False? Make sure you locate and adhere to...Ch. 13 - How does a torque-to-yield bolt differ from...Ch. 13 - How do seals differ from gaskets?Ch. 13 - Where are thread sealers most often used?Ch. 13 - What are the major differences between aerobic and...Ch. 13 - Which of the following statements is incorrect?...Ch. 13 - True or False? Valve lash is adjusted in many...Ch. 13 - Which of the following statements about the...Ch. 13 - True or False? The computer in most late-model...Ch. 13 - Graphite is. an anaerobic substance an RTV an...
Ch. 13 - Which of the following are considered soft, cut...Ch. 13 - What material is typically not used to form a rear...Ch. 13 - Which of the following statements about preparing...Ch. 13 - On hybrid vehicles, how can you identify the high...Ch. 13 - True or False? Some crankshaft and camshaft timing...Ch. 13 - Prob. 1ASRQCh. 13 - Technician A uses adhesives to hold gaskets in...Ch. 13 - Technician A uses soft gaskets on valve covers....Ch. 13 - Technician A inspects all sealing surfaces for...Ch. 13 - Technician A says that oil pan gaskets are often...Ch. 13 - Prob. 6ASRQCh. 13 - While discussing proper engine break-in:...Ch. 13 - Prob. 8ASRQCh. 13 - Prob. 9ASRQCh. 13 - While selecting the proper RTV for a particular...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- Technician A uses adhesives to hold gaskets in place while installing them. Technician B uses RTV sealant on all surfaces that are prone to leaks. Who is correct? Technician A Technician B Both A and B Neither A nor Barrow_forwardWhile discussing the reasons for resurfacing a cylinder head; Technician A says it should be resurfaced to make it flat and very smooth so the head gasket can seal properly during engine assembly. Technician B says that it can be resurfaced to raise the compression. Who is correct? Technician A Technician B Both A and B Neither A nor Barrow_forwardWhile discussing thread sealants and lubricants: Technician A says that antiseize compound is used where a bolt might become difficult to remove after a period of time. Technician B says that thread sealants are used on bolts that are tightened into an oil cavity or coolant passage. Who is correct? Technician A Technician B Both A and B Neither A nor Barrow_forward
- Technician A says head gasket thickness has an effect on compression ratio. Technician B says connecting rod length has an effect on compression ratio. Who is correct? Technician A Technician B Both A and B Neither A nor Barrow_forwardTechnician A uses soft gaskets on valve covers. Technician B uses soft gaskets on water pumps. Who is correct? Technician A Technician B Both A and B Neither A nor Barrow_forwardWhat material is typically not used to form a rear main bearing oil seal? Polyacrylate RTV Silicone synthetic rubber Vitonarrow_forward
- Technician A says that oil pan gaskets are often made of cork due to its ability to conform to small imperfections in the oil pan. Technician B says oil pan and valve cover gaskets are often MLS gaskets to account for the different expansion rates between components. Who is correct? Technician A Technician B Both A and B Neither A nor Barrow_forwardWhile diagnosing the cause of air bubbles in the coolant recovery tank: Technician A checks for a bad head gasket. Technician B checks the radiator cap. Who is correct? Technician A Technician B Both A and B Neither A nor Barrow_forwardWhich of the following is not a type of valve guide seal? Positive Negative Umbrella O-ringarrow_forward
- How do seals differ from gaskets?arrow_forwardWhich of the following statements about the purpose of a cylinder head gasket is not true? It seals intake stroke vacuum, combustion pressure, and the heat of combustion. It prevents coolant leakage and resists rust, corrosion and, in many cases, meters coolant flow. It allows for lateral and vertical head movement as the engine heats and cools. It meters lubricating oil onto the engines cylinder walls.arrow_forwardThe piston rings are used to act as a seal between the piston and cylinder head a. FALSE b. TRUEarrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Automotive Technology: A Systems Approach (MindTa...Mechanical EngineeringISBN:9781133612315Author:Jack Erjavec, Rob ThompsonPublisher:Cengage LearningAutomotive TechnologyMechanical EngineeringISBN:9781337794213Author:ERJAVEC, Jack.Publisher:Cengage,Refrigeration and Air Conditioning Technology (Mi...Mechanical EngineeringISBN:9781305578296Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill JohnsonPublisher:Cengage Learning
Automotive Technology: A Systems Approach (MindTa...
Mechanical Engineering
ISBN:9781133612315
Author:Jack Erjavec, Rob Thompson
Publisher:Cengage Learning
Automotive Technology
Mechanical Engineering
ISBN:9781337794213
Author:ERJAVEC, Jack.
Publisher:Cengage,
Refrigeration and Air Conditioning Technology (Mi...
Mechanical Engineering
ISBN:9781305578296
Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson
Publisher:Cengage Learning
Materials Science Mechanical Engineering - Part 3 Corrosion Explained; Author: Mega Mechatronics;https://www.youtube.com/watch?v=Il-abRhrzFY;License: Standard Youtube License