Automotive Technology: A Systems Approach (MindTap Course List)
6th Edition
ISBN: 9781133612315
Author: Jack Erjavec, Rob Thompson
Publisher: Cengage Learning
expand_more
expand_more
format_list_bulleted
Concept explainers
Textbook Question
Chapter 13, Problem 6RQ
Which of the following statements is incorrect?
- Cylinder head bolts must be tightened to the proper amount of torque.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solutionStudents have asked these similar questions
True or false
Gears and crankshaft are transmitting type of short distance power type of transmission
Why is it important to loosen the cylinder head bolts in the recommended order?
Which of the following is not measured with a feelergauge set?a. Piston ring side clearanceb. Flywheel runoutc. Crankshaft end playd. Spark plug gap
Chapter 13 Solutions
Automotive Technology: A Systems Approach (MindTap Course List)
Ch. 13 - True or False? Make sure you locate and adhere to...Ch. 13 - How does a torque-to-yield bolt differ from...Ch. 13 - How do seals differ from gaskets?Ch. 13 - Where are thread sealers most often used?Ch. 13 - What are the major differences between aerobic and...Ch. 13 - Which of the following statements is incorrect?...Ch. 13 - True or False? Valve lash is adjusted in many...Ch. 13 - Which of the following statements about the...Ch. 13 - True or False? The computer in most late-model...Ch. 13 - Graphite is. an anaerobic substance an RTV an...
Ch. 13 - Which of the following are considered soft, cut...Ch. 13 - What material is typically not used to form a rear...Ch. 13 - Which of the following statements about preparing...Ch. 13 - On hybrid vehicles, how can you identify the high...Ch. 13 - True or False? Some crankshaft and camshaft timing...Ch. 13 - Prob. 1ASRQCh. 13 - Technician A uses adhesives to hold gaskets in...Ch. 13 - Technician A uses soft gaskets on valve covers....Ch. 13 - Technician A inspects all sealing surfaces for...Ch. 13 - Technician A says that oil pan gaskets are often...Ch. 13 - Prob. 6ASRQCh. 13 - While discussing proper engine break-in:...Ch. 13 - Prob. 8ASRQCh. 13 - Prob. 9ASRQCh. 13 - While selecting the proper RTV for a particular...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
Which of the following statements about the purpose of a cylinder head gasket is not true? It seals intake stroke vacuum, combustion pressure, and the heat of combustion. It prevents coolant leakage and resists rust, corrosion and, in many cases, meters coolant flow. It allows for lateral and vertical head movement as the engine heats and cools. It meters lubricating oil onto the engines cylinder walls.
arrow_forward
Which of the following are not typically found in the block of a modern engine? a. Pistons b. Crankshaft c. Valves d. Oil pump
arrow_forward
True or False? The first step in removing an engine is usually the removal of the intake and exhaust manifolds.
arrow_forward
True or False? The vent in a transmission housing is designed to allow fluid to escape when there is excessive pressure in the system.
arrow_forward
The piston rings are used to act as a seal between the piston and cylinder head
a.
FALSE
b.
TRUE
arrow_forward
Gears and crankshaft are transmitting type of short distance power type of transmission.
Select one:
True
False
arrow_forward
Which of the following statements about preparing to assemble an engine is not true? Discard and replace all bolts that are damaged. Identify what bolts go into the specific bores. Use a thread locker on all bolts. Clean bolt and cylinder block threads with a thread chaser or tap.
arrow_forward
Which of the following is not measured with a feeler gauge set? Piston ring side clearance Flywheel runout Crankshaft end play Spark plug gap
arrow_forward
Which of the following is not a type of valve guide seal? Positive Negative Umbrella O-ring
arrow_forward
List five problems that can be caused by engine overheating.
arrow_forward
Which of the following is probably not the cause of a vibrating clutch? a. Excessive crankshaft end play b. Out-of-balance pressure plate assembly c. Excessive flywheel runout d. Loose flywheel bolts
arrow_forward
While discussing the reasons for resurfacing a cylinder head; Technician A says it should be resurfaced to make it flat and very smooth so the head gasket can seal properly during engine assembly. Technician B says that it can be resurfaced to raise the compression. Who is correct? Technician A Technician B Both A and B Neither A nor B
arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Automotive Technology: A Systems Approach (MindTa...
Mechanical Engineering
ISBN:9781133612315
Author:Jack Erjavec, Rob Thompson
Publisher:Cengage Learning
Automotive Technology
Mechanical Engineering
ISBN:9781337794213
Author:ERJAVEC, Jack.
Publisher:Cengage,
Automotive Technology: A Systems Approach (MindTa...
Mechanical Engineering
ISBN:9781133612315
Author:Jack Erjavec, Rob Thompson
Publisher:Cengage Learning
Automotive Technology
Mechanical Engineering
ISBN:9781337794213
Author:ERJAVEC, Jack.
Publisher:Cengage,
Principles of Lubrication | Automobile Engineering; Author: Magic Marks;https://www.youtube.com/watch?v=MGbbSxZTdCQ;License: Standard Youtube License