Automotive Technology: A Systems Approach (MindTap Course List)
6th Edition
ISBN: 9781133612315
Author: Jack Erjavec, Rob Thompson
Publisher: Cengage Learning
expand_more
expand_more
format_list_bulleted
Concept explainers
Question
Chapter 13, Problem 9ASRQ
To determine
Before reusing head or other critical bolts: The technician with correct approach.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solutionStudents have asked these similar questions
Technician A says a bolt may become fatigued if it is over tightened. Technician B says that a bolt may become fatigued if it is under tightened. Who is correct?
True or false
Gears and crankshaft are transmitting type of short distance power type of transmission
Technician A says a metric bolt with the marking of 8.9 has more yield strength than a 10.9 bolt. Technician B says only grade 8 nuts should be used on 10.9 rated bolt. Who is correct?
Chapter 13 Solutions
Automotive Technology: A Systems Approach (MindTap Course List)
Ch. 13 - True or False? Make sure you locate and adhere to...Ch. 13 - How does a torque-to-yield bolt differ from...Ch. 13 - How do seals differ from gaskets?Ch. 13 - Where are thread sealers most often used?Ch. 13 - What are the major differences between aerobic and...Ch. 13 - Which of the following statements is incorrect?...Ch. 13 - True or False? Valve lash is adjusted in many...Ch. 13 - Which of the following statements about the...Ch. 13 - True or False? The computer in most late-model...Ch. 13 - Graphite is. an anaerobic substance an RTV an...
Ch. 13 - Which of the following are considered soft, cut...Ch. 13 - What material is typically not used to form a rear...Ch. 13 - Which of the following statements about preparing...Ch. 13 - On hybrid vehicles, how can you identify the high...Ch. 13 - True or False? Some crankshaft and camshaft timing...Ch. 13 - Prob. 1ASRQCh. 13 - Technician A uses adhesives to hold gaskets in...Ch. 13 - Technician A uses soft gaskets on valve covers....Ch. 13 - Technician A inspects all sealing surfaces for...Ch. 13 - Technician A says that oil pan gaskets are often...Ch. 13 - Prob. 6ASRQCh. 13 - While discussing proper engine break-in:...Ch. 13 - Prob. 8ASRQCh. 13 - Prob. 9ASRQCh. 13 - While selecting the proper RTV for a particular...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- While discussing the reasons for resurfacing a cylinder head; Technician A says it should be resurfaced to make it flat and very smooth so the head gasket can seal properly during engine assembly. Technician B says that it can be resurfaced to raise the compression. Who is correct? Technician A Technician B Both A and B Neither A nor Barrow_forwardWhile discussing thread sealants and lubricants: Technician A says that antiseize compound is used where a bolt might become difficult to remove after a period of time. Technician B says that thread sealants are used on bolts that are tightened into an oil cavity or coolant passage. Who is correct? Technician A Technician B Both A and B Neither A nor Barrow_forwardTechnician A says head gasket thickness has an effect on compression ratio. Technician B says connecting rod length has an effect on compression ratio. Who is correct? Technician A Technician B Both A and B Neither A nor Barrow_forward
- Technician A inspects all sealing surfaces for damage and uses a supplementary sealant on the gaskets if the surface is questionable. Technician B coats the intake gasket on some engines with a nonhardening sealer. Who is correct? Technician A Technician B Both A and B Neither A nor Barrow_forwardWhich of the following statements about preparing to assemble an engine is not true? Discard and replace all bolts that are damaged. Identify what bolts go into the specific bores. Use a thread locker on all bolts. Clean bolt and cylinder block threads with a thread chaser or tap.arrow_forwardWhich of the following statements is incorrect? Cylinder head bolts must be tightened to the proper amount of torque. Most cylinder head bolts are tightened in a sequence that starts on one end. On some engines, the head bolts are retorqued after the engine has been run and is hot. Many engines use head bolts of different lengths.arrow_forward
- Technician A uses soft gaskets on valve covers. Technician B uses soft gaskets on water pumps. Who is correct? Technician A Technician B Both A and B Neither A nor Barrow_forwardCHECH THE NUMBER OF BOLTS AT JOINT A AND Barrow_forwardAfter draining gear oil from a transaxle, the techniciannotices that the oil has shiny, metallic particles init. What does this indicate?arrow_forward
- What material is typically not used to form a rear main bearing oil seal? Polyacrylate RTV Silicone synthetic rubber Vitonarrow_forwardTechnician A uses adhesives to hold gaskets in place while installing them. Technician B uses RTV sealant on all surfaces that are prone to leaks. Who is correct? Technician A Technician B Both A and B Neither A nor Barrow_forwardList three items that can be checked during a visual inspection of a butt joint.arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Automotive Technology: A Systems Approach (MindTa...Mechanical EngineeringISBN:9781133612315Author:Jack Erjavec, Rob ThompsonPublisher:Cengage LearningRefrigeration and Air Conditioning Technology (Mi...Mechanical EngineeringISBN:9781305578296Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill JohnsonPublisher:Cengage LearningWelding: Principles and Applications (MindTap Cou...Mechanical EngineeringISBN:9781305494695Author:Larry JeffusPublisher:Cengage Learning
Automotive Technology: A Systems Approach (MindTa...
Mechanical Engineering
ISBN:9781133612315
Author:Jack Erjavec, Rob Thompson
Publisher:Cengage Learning
Refrigeration and Air Conditioning Technology (Mi...
Mechanical Engineering
ISBN:9781305578296
Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson
Publisher:Cengage Learning
Welding: Principles and Applications (MindTap Cou...
Mechanical Engineering
ISBN:9781305494695
Author:Larry Jeffus
Publisher:Cengage Learning