Automotive Technology: A Systems Approach (MindTap Course List)
6th Edition
ISBN: 9781133612315
Author: Jack Erjavec, Rob Thompson
Publisher: Cengage Learning
expand_more
expand_more
format_list_bulleted
Textbook Question
Chapter 14, Problem 1ASRQ
Technician A uses a feeler gauge and straightedge to determine the pump cover flatness. Technician B uses an outside micrometer to measure the diameter and thickness of the outer rotor. Who is correct?
- Technician A
Expert Solution & Answer
Trending nowThis is a popular solution!
Students have asked these similar questions
Technician A uses a feeler gauge and straightedge to determine the pump cover flatness.Technician B uses an outside micrometer tomeasure the diameter and thickness of theouter rotor. Who is correct?a. Technician Ab. Technician Bc. Both A and Bd. Neither A nor B
True or False? Oil pressure is determined bywhether the pump is a gear type or rotor typeand by oil clearances, the pump’s pressure regulator valve, and oil viscosity.
Technician A says that a stator aids in directing the flow of fluid from the impeller to the turbine. Technician B says that a stator is equipped with a one-way clutch that allows it to remain stationary when necessary. Who is correct?
Chapter 14 Solutions
Automotive Technology: A Systems Approach (MindTap Course List)
Ch. 14 - What is the most efficient way to increase a...Ch. 14 - True or False? Oil pressure is determined by...Ch. 14 - Describe the simple test used to determine whether...Ch. 14 - Which of the following is a function of the...Ch. 14 - What is ECD and what can result from it?Ch. 14 - True or False? To eliminate the drain of engine...Ch. 14 - For every pound of pressure put on engine coolant,...Ch. 14 - Which is not a typical method of driving the water...Ch. 14 - Which of the following is not an effective way to...Ch. 14 - Explain why a pressure relief valve is needed in...
Ch. 14 - List five problems that can be caused by engine...Ch. 14 - Cooling system hoses should be replaced when they...Ch. 14 - True or False? The presence of air in the cooling...Ch. 14 - Which of the following is not a true statement...Ch. 14 - Describe the procedure for using air bleed valves...Ch. 14 - Technician A uses a feeler gauge and straightedge...Ch. 14 - Technician A says that excessive engine oil...Ch. 14 - While checking for conditions that might cause...Ch. 14 - When installing an oil pump in an engine...Ch. 14 - Technician A says that if the PCV valve or...Ch. 14 - While bleeding air from a cooling system:...Ch. 14 - While diagnosing an engine that overheats after...Ch. 14 - While performing a cooling system service on a...Ch. 14 - While discussing the causes of extreme engine...Ch. 14 - While diagnosing the cause of air bubbles in the...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
Technician A uses a feeler gauge and straightedge to determine the pump cover flatness. Technician B uses an outside micrometer to measure the diameter and thickness of the outer rotor. Who is correct? a. Technician A b. Technician B c. Both A and B d. Neither A nor B
arrow_forward
True or False? Oil pressure is determined by whether the pump is a gear type or rotor type and by oil clearances, the pumps pressure regulator valve, and oil viscosity.
arrow_forward
Technician A says that positive valve stem seals fit tightly around the top of the valve guide. Technician B says that positive stem seals scrape oil off the valve as it moves up and down. Who is correct? Technician A Technician B Both A and B Neither A nor B
arrow_forward
Which of the following is not a type of valve guide seal? Positive Negative Umbrella O-ring
arrow_forward
Technician A says it is not necessary to measure valve stem height unless the valves have been replaced. Technician B says valve stem height can be adjusted with shims. Who is correct? Technician A Technician B Both A and B Neither A nor B
arrow_forward
An instrument often used to check the alignment of twoshafts is theA. micrometer.B. dial indicator.C. manometer.D. sling psychrometer.
arrow_forward
Technician A says that some shift solenoids can be activated by providing a ground for the solenoid. Technician B says that some shift solenoids can be activated by applying hydraulic pressure to their valve. Who is correct?
arrow_forward
Pressure readings reveal possible problems in which of the following? a. Oil pump b. Governor c. Apply circuits d. All of the above
arrow_forward
In Pensky Martin's apparatus what is the purpose of air jacket surrounding the oil cup.
arrow_forward
Which of the following statements about drum brakeshoes is not true?a. Web thickness varies only with changes in shoesize.b. Many shoes have indented places along the edgeof the rim.c. The shoe rim is welded to the web.d. The primary/leading shoe is typically the one thatis positioned toward the front of the vehicle
arrow_forward
Which of the following is not measured when inspecting the brake rotors and pads?
Out of round
Rotor thickness
Runout
Pad thickness
arrow_forward
find Torque Required to Apply Brake.
arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Automotive Technology: A Systems Approach (MindTa...
Mechanical Engineering
ISBN:9781133612315
Author:Jack Erjavec, Rob Thompson
Publisher:Cengage Learning
Automotive Technology
Mechanical Engineering
ISBN:9781337794213
Author:ERJAVEC, Jack.
Publisher:Cengage,
Refrigeration and Air Conditioning Technology (Mi...
Mechanical Engineering
ISBN:9781305578296
Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson
Publisher:Cengage Learning
Automotive Technology: A Systems Approach (MindTa...
Mechanical Engineering
ISBN:9781133612315
Author:Jack Erjavec, Rob Thompson
Publisher:Cengage Learning
Automotive Technology
Mechanical Engineering
ISBN:9781337794213
Author:ERJAVEC, Jack.
Publisher:Cengage,
Refrigeration and Air Conditioning Technology (Mi...
Mechanical Engineering
ISBN:9781305578296
Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson
Publisher:Cengage Learning
Mod-01 Lec-16 Basics of Instrumentation; Author: nptelhrd;https://www.youtube.com/watch?v=qbKnW42ZM5c;License: Standard YouTube License, CC-BY