Engineering Fundamentals: An Introduction to Engineering (MindTap Course List)
5th Edition
ISBN: 9781305084766
Author: Saeed Moaveni
Publisher: Cengage Learning
expand_more
expand_more
format_list_bulleted
Concept explainers
Question
Chapter 15, Problem 11P
To determine
Using MATLAB, plot the deflection of a beam and find the maximum deflection of the beam.
Expert Solution & Answer
Trending nowThis is a popular solution!
Students have asked these similar questions
The cantilevered beam shown in the accompanying figure is used to support a load acting on a balcony. The deflection of the centerline of the beam is given by the following equation: y = deflection at a given x location (m)w = distributed load (N/m)E = modulus of elasticity (N⁄m2 )I = second moment of area (m4 )x = distance from the support as shown ( x )L = length of the beam (m) Using Excel, plot the deflection of a beam whose length is 5 m with themodulus of elasticity of E = 200 GPa and I = 99.1×106 mm4 . The beam is designed to carry a load of 10,000 N/m. What is the maximum deflection of the beam?
the relation between the spring force (f) and its deflection(x) is given in the table. using the engineering paper below, plot the force against the deflection. determine the spring constant(k), using the equation f=kx
deflection (x)
0,5,10,15,20
spring force f(N)
0,10,20,30,40
In the given figure below, a tube was supported at A and E with a ball and socket and a wire at D connected to F. Determine the following give that Force F is equal to 690.86 N.
Note: Express your answer in terms of the units.
Observe 3 decimal places.
The error threshold is ± 2.50% Relative to the right answer.
XB: 188.419mm
Xc: 471.768mm
Ya: 209.808mm
Ze: 155.444 mm
Zf: 471.096 mm
5.) Determine the x-component of the moment experienced by the system assuming that there is no wire support.
6.) Determine the y-component of the moment experienced by the system assuming that there is no wire support.
7.) Determine the z-component of the moment experienced by the system assuming that there is no wire support.
8.) Determine the Tension experienced by the wire DF.
Chapter 15 Solutions
Engineering Fundamentals: An Introduction to Engineering (MindTap Course List)
Ch. 15.1 - Prob. 1BYGCh. 15.1 - Prob. 2BYGCh. 15.1 - Prob. 3BYGCh. 15.1 - Prob. 4BYGCh. 15.1 - Prob. 5BYGCh. 15.2 - Prob. 1BYGCh. 15.2 - Prob. 2BYGCh. 15.2 - Prob. 3BYGCh. 15.2 - What is an M-file?Ch. 15.5 - Prob. 1BYG
Ch. 15.5 - Prob. 2BYGCh. 15.5 - Prob. 3BYGCh. 15.5 - Prob. 4BYGCh. 15.5 - Prob. 5BYGCh. 15 - Prob. 1PCh. 15 - Prob. 2PCh. 15 - Prob. 3PCh. 15 - Prob. 4PCh. 15 - Prob. 5PCh. 15 - Prob. 6PCh. 15 - Prob. 7PCh. 15 - Prob. 8PCh. 15 - Prob. 9PCh. 15 - Prob. 10PCh. 15 - Prob. 11PCh. 15 - Prob. 12PCh. 15 - Prob. 13PCh. 15 - Prob. 14PCh. 15 - Prob. 15PCh. 15 - Prob. 16PCh. 15 - Prob. 17PCh. 15 - Prob. 18PCh. 15 - Prob. 19PCh. 15 - Prob. 20PCh. 15 - Prob. 21PCh. 15 - Prob. 22PCh. 15 - Prob. 23PCh. 15 - Prob. 24PCh. 15 - Prob. 25PCh. 15 - Prob. 26PCh. 15 - Prob. 27PCh. 15 - Prob. 28PCh. 15 - Prob. 29PCh. 15 - Prob. 30PCh. 15 - Prob. 31PCh. 15 - The Body Mass Index (BMI) is a way of determining...Ch. 15 - Prob. 33PCh. 15 - Prob. 34PCh. 15 - Prob. 35PCh. 15 - Prob. 36PCh. 15 - Prob. 37PCh. 15 - Prob. 38PCh. 15 - Prob. 39PCh. 15 - Prob. 40P
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.Similar questions
- We have used an experimental setup similar to Example 10.1 to determine the value of a spring constant. The deflection caused by the corresponding weights are given in the accompanying table. What is the value of the spring constant? Weight (lb) The Deflection of the Spring (in.) 5.0 0.48 10.0 1.00 15.0 1.90 20.0 2.95arrow_forwardIn the figure, a motor weighing 3000 N hangs from a chain attached by an O-ring to two other chains, one attached to the ceiling and the other to the wall. Calculate the tension force T2 acting on the chain attached to the wall. Consider that the weights of the chains and the ring are negligible. solve and choose the correct alternative A) 3464 N B) 1732 N C) 346.4 N D) 173.2 Narrow_forward4. This figure shows a cantilever beam that is subject to a point load and a moment. What is the vertical displacement at the tip of the beam? Assume E = 200 GPa and / = 1560 X 10° mm%. A. 58.7 mm B. 68.9 mm C. 89.0 mm D. 100 mmarrow_forward
- In the figure below, the weight of the block is 300 kg and the angle of internal friction is 24.2 degrees. a. If h = 50 cm and P = 50 kg. does the block move? b. If h = 50 cm, what is the smallest P to start motion?arrow_forwardShow the complete solution and the necessary graphs/diagrams. Use 2 decimal places in the final answer. A particle moves that is defined by the parametric equations given below (where x and y are in meters, and t is in seconds). Compute the transverse component of the acceleration (m/s^2) at t = 2 seconds.arrow_forwardCalculate the y coordinate of the center of gravity of the shaded area given in the figure. a(mm)=145 b(mm)=45 c(mm)=30 d(mm)=290 e(mm)=35arrow_forward
- Show the complete solution and the necessary graphs/diagrams. Use 2 decimal places in the final answer. A particle moves that is defined by the parametric equations given below (where x and y are in meters, and t is in seconds). Compute the radial component of the acceleration (m/s^2) at t = 2 seconds.arrow_forwardA person by the name of Huebscher developed a relationship between theequivalent size of round ducts and rectangular ducts according to D = diameter of equivalent circular duct (mm)a = dimension of one side of the rectangular duct (mm)b = the other dimension of the rectangular duct (mm)Using Excel, create a table that shows the relationship between the circular and the rectangular duct dimensions, similar to the one shown in the accompanying table.arrow_forwardIn the figure shown, an open tank when empty the water surface is at point A and the gauge fluid mercury shows a deflection of 20mm. Determine the new deflection of mercury when the tank is filled with water to B.arrow_forward
- Please include the figured and please write the true answer. Please make sure that it is 2 decimal points in every answer. Please double check your calculations and please put the formula that had been used and the explanationarrow_forwardA Pitot tube is a device commonly used in a wind tunnel to measure the speed of the air flowing over a model. The air speed is measured from the following equation: Using Excel, create a table that shows the air speed for the range of dynamic pressure of 500 to 800 Pa. Use increments of 50 Pa.arrow_forward
arrow_back_ios
arrow_forward_ios
Recommended textbooks for you
- Engineering Fundamentals: An Introduction to Engi...Civil EngineeringISBN:9781305084766Author:Saeed MoaveniPublisher:Cengage Learning
Engineering Fundamentals: An Introduction to Engi...
Civil Engineering
ISBN:9781305084766
Author:Saeed Moaveni
Publisher:Cengage Learning