Automotive Technology: A Systems Approach (MindTap Course List)
6th Edition
ISBN: 9781133612315
Author: Jack Erjavec, Rob Thompson
Publisher: Cengage Learning
expand_more
expand_more
format_list_bulleted
Concept explainers
Question
Chapter 16, Problem 4RQ
To determine
The causes of unwanted or higher resistance in a circuit.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
Higher pairs are those which have
Choose the correct option
Surface contact between elements
Point or line contact between elements
None of the mentioned
No contact between elements
what would be the resistance of a circuit that is open
From the following identify the false statement .
A) In electrical safety precaution, necessary steps should be taken to avoid overloading of electrical circuits.
B) In housekeeping safety precaution, the machine should be cleared with tools before starting the operation.
C) In general safety precaution, the operator should be familiar with the emergency stop button on the machines.
E) In general safety precaution, the machine tool should be cleared with metal chips after the machining process.
Chapter 16 Solutions
Automotive Technology: A Systems Approach (MindTap Course List)
Ch. 16 - How will an electrical circuit behave if there is...Ch. 16 - What happens to an electrical circuit when there...Ch. 16 - Prob. 3RQCh. 16 - Prob. 4RQCh. 16 - Wiring harnesses are typically shielded by plastic...Ch. 16 - True or False? The MIN/MAX function on some DMMs...Ch. 16 - True or False? A zero reading on an ohmmeter means...Ch. 16 - Prob. 8RQCh. 16 - What type of solder should be used to repair...Ch. 16 - Which of the following lab scope controls must be...
Ch. 16 - Prob. 11RQCh. 16 - Prob. 12RQCh. 16 - Prob. 13RQCh. 16 - Which of the following information is not given in...Ch. 16 - While troubleshooting a problem, the key to...Ch. 16 - While discussing electricity: Technician A says...Ch. 16 - While discussing NTC thermistors: Technician A...Ch. 16 - While measuring the resistance of a wire with an...Ch. 16 - While testing variable resistors: Technician A...Ch. 16 - Prob. 5ASRQCh. 16 - Technician A uses a testlight to test circuit...Ch. 16 - Technician A uses a testlight to detect...Ch. 16 - While diagnosing the location of a wire-to-wire...Ch. 16 - While measuring resistance: Technician A uses an...Ch. 16 - While discussing how to test a switch: Technician...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- True or False? A zero reading on an ohmmeter means the circuit or component is open.arrow_forwardWhile diagnosing the location of a wire-to-wire short: Technician A checks the wiring of the affected circuits for signs of burned insulation and melted conductors. Technician B checks common connectors shared by the two affected circuits. Who is correct? Technician A Technician B Both A and B Neither A nor Barrow_forwardTrue or False? A batteny is an electromechanical device.arrow_forward
- Which of the following tests would not be performed to check for high resistance in the battery' cables? Cranking voltage test Insulated circuit resistance test Starter relay by-pass test Ground circuit resistance testarrow_forwardWhat is the device that consists of two unlike metal strips that are attached and have a different rate of expansion and contraction? A. Thermistor B. Thermocouple C. Diaphragm D. Bimetalarrow_forwardWhile measuring the resistance of a wire with an ohmmeter: Technician A says that if low resistance is shown on the meter, the wire is shorted. Technician B says that if no resistance is measured, the wire is shorted. Who is correct? Technician A Technician B Both A and B d. Neither A nor Barrow_forward
- True or False? A faulty voltage regulator can only cause a no-charge condition.arrow_forwardTrue or False: When troubleshooting a small system, the first step is to attach the high- and low-pressure gauges.arrow_forwardDescribe the characteristics of the voltage, amperage, and resistances when there is more than one load in a parallel circuit.arrow_forward
- Which of the following is not made of semiconductor material? Zener diode Thermistor PM generator Hall-effect switcharrow_forwardWhat happens to an electrical circuit when thereis unwanted resistance in it?arrow_forwardThe circuit breaker at a power seat motor continuously trips: Technician A says that this could be caused by a seat track problem that is causing mechanical resistance. Technician B says that this could be caused by corrosion at the motor, which is causing electrical re-sistance. Who is correct?arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Automotive Technology: A Systems Approach (MindTa...Mechanical EngineeringISBN:9781133612315Author:Jack Erjavec, Rob ThompsonPublisher:Cengage Learning
Refrigeration and Air Conditioning Technology (Mi...Mechanical EngineeringISBN:9781305578296Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill JohnsonPublisher:Cengage Learning
Automotive TechnologyMechanical EngineeringISBN:9781337794213Author:ERJAVEC, Jack.Publisher:Cengage,
Automotive Technology: A Systems Approach (MindTa...
Mechanical Engineering
ISBN:9781133612315
Author:Jack Erjavec, Rob Thompson
Publisher:Cengage Learning
Refrigeration and Air Conditioning Technology (Mi...
Mechanical Engineering
ISBN:9781305578296
Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson
Publisher:Cengage Learning
Automotive Technology
Mechanical Engineering
ISBN:9781337794213
Author:ERJAVEC, Jack.
Publisher:Cengage,