Automotive Technology: A Systems Approach (MindTap Course List)
6th Edition
ISBN: 9781133612315
Author: Jack Erjavec, Rob Thompson
Publisher: Cengage Learning
expand_more
expand_more
format_list_bulleted
Concept explainers
Textbook Question
Chapter 16, Problem 8ASRQ
While diagnosing the location of a wire-to-wire short: Technician A checks the wiring of the affected circuits for signs of burned insulation and melted conductors. Technician B checks common connectors shared by the two affected circuits. Who is correct?
- Technician A
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solutionStudents have asked these similar questions
The circuit breaker at a power seat motor continuously trips: Technician A says that this could be caused by a seat track problem that is causing mechanical resistance. Technician B says that this could be caused by corrosion at the motor, which is causing electrical re-sistance. Who is correct?
In the secondary circuit, what is the function of modern ignition cables that contain carbon fibre cores?
semiconductor
conductor
resistor
ground
How do most electronic ignition systems differ?
number of spark plugs
the use of CMP and CKP sensors
number of transistors
the use of a distributor
Chapter 16 Solutions
Automotive Technology: A Systems Approach (MindTap Course List)
Ch. 16 - How will an electrical circuit behave if there is...Ch. 16 - What happens to an electrical circuit when there...Ch. 16 - Prob. 3RQCh. 16 - Prob. 4RQCh. 16 - Wiring harnesses are typically shielded by plastic...Ch. 16 - True or False? The MIN/MAX function on some DMMs...Ch. 16 - True or False? A zero reading on an ohmmeter means...Ch. 16 - Prob. 8RQCh. 16 - What type of solder should be used to repair...Ch. 16 - Which of the following lab scope controls must be...
Ch. 16 - Prob. 11RQCh. 16 - Prob. 12RQCh. 16 - Prob. 13RQCh. 16 - Which of the following information is not given in...Ch. 16 - While troubleshooting a problem, the key to...Ch. 16 - While discussing electricity: Technician A says...Ch. 16 - While discussing NTC thermistors: Technician A...Ch. 16 - While measuring the resistance of a wire with an...Ch. 16 - While testing variable resistors: Technician A...Ch. 16 - Prob. 5ASRQCh. 16 - Technician A uses a testlight to test circuit...Ch. 16 - Technician A uses a testlight to detect...Ch. 16 - While diagnosing the location of a wire-to-wire...Ch. 16 - While measuring resistance: Technician A uses an...Ch. 16 - While discussing how to test a switch: Technician...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- While discussing electrical grounds: Technician A says that a component may be grounded through its mounting to a major metal part. Technician B says that some components must be grounded by connecting its positive terminal to a metal section of the frame. Who is correct? Technician A Technician B Both A and B Neither A nor Barrow_forwardWhich of the following tests would not be performed to check for high resistance in the battery' cables? Cranking voltage test Insulated circuit resistance test Starter relay by-pass test Ground circuit resistance testarrow_forwardWhile measuring the resistance of a wire with an ohmmeter: Technician A says that if low resistance is shown on the meter, the wire is shorted. Technician B says that if no resistance is measured, the wire is shorted. Who is correct? Technician A Technician B Both A and B d. Neither A nor Barrow_forward
- While discussing copper wire: Technician A says that if the length of wire is doubled, the resistance between the wire ends is doubled. Technician B says that if the diameter of a wire is doubled, the resistance between the wire ends is doubled. Who is correct? Technician A Technician B Both A and B Neither A nor Barrow_forwardWiring harnesses are typically shielded by plastic conduit. What color is normally used to shield SRS- related wiring? Black Green c. Yellow d. Orangearrow_forwardTechnician A uses a testlight to test circuit protection devices. Technician B uses a voltmeter to test circuit protection devices. Who is correct? Technician A Technician B Both A and B Neither A nor Barrow_forward
- While discussing spark plugs: Technician A says that too narrow of a spark plug gap can cause a rough idle and premature wear of the electrodes. Technician B says that a spark plug with the wrong reach can cause preignition. Who is correct? a. Technician A b. Technician B c. Both A and B d. Neither A nor Barrow_forwardWhich of the following is a device consisting of two unlike metals fastened at one end that, when heated on the fastened end, produces a DC current? A. Thermocouple B. Thermistor C. Diaphragm D. Bimetalarrow_forwardTechnician A labels or marks all electrical wires before disconnecting them. Technician B labels or marks all vacuum hoses and verities the connections to the underhood decal before disconnecting them. Who is correct? Technician A Technician B Both A and B Neither A nor Barrow_forward
- True or False? A zero reading on an ohmmeter means the circuit or component is open.arrow_forwardTrue or False? A batteny is an electromechanical device.arrow_forwardWhile measuring resistance: Technician A uses an ohmmeter to measure resistance of a component before disconnecting it from the circuit. Technician B uses a voltmeter to measure voltage drop. A circuit with very low resistance will drop zero or very little voltage. Who is correct? Technician A Technician B Both A and B Neither A nor Barrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Automotive Technology: A Systems Approach (MindTa...Mechanical EngineeringISBN:9781133612315Author:Jack Erjavec, Rob ThompsonPublisher:Cengage LearningRefrigeration and Air Conditioning Technology (Mi...Mechanical EngineeringISBN:9781305578296Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill JohnsonPublisher:Cengage Learning
Automotive Technology: A Systems Approach (MindTa...
Mechanical Engineering
ISBN:9781133612315
Author:Jack Erjavec, Rob Thompson
Publisher:Cengage Learning
Refrigeration and Air Conditioning Technology (Mi...
Mechanical Engineering
ISBN:9781305578296
Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson
Publisher:Cengage Learning
Materials Science Mechanical Engineering - Part 3 Corrosion Explained; Author: Mega Mechatronics;https://www.youtube.com/watch?v=Il-abRhrzFY;License: Standard Youtube License