How much filler metal should be added to a filler bead?

Q: How much of the surface beside a weld groove must be cleaned for the AWS SENSE workmanship samples?

A: AWS stands for American Welding Society. SENSE  Schools Excelling through National Skills Standards…

Q: A fillet weld can be used to join which of the following joint types: *

A:

Q: What are the grooves most often used for welding on mild steel pipe

A: Single V Single U Single J Single bevel grooves

Q: 12)In resistance spot welding process the time between pressure application and weld is called:

A: Solution:

Q: In addition to continuously changing the weld pattern,what other changes must be continually made…

A: Considered to be the most challenging pipe position is the 66 or 45° fixed inclined position.…

Q: 3. Explain about pipeline pigging?

A: Solution:   Pigging in Pipeline is explained below:

Q: Why should there be a space between the plates whenmaking a fillet weld on thick plates of a tee…

A: Fillet welding refers to the process of joining two pieces of metal together when they are…

Q: The correct words for the blanks are

A: Given; In case of tubulent flow of a fluid flow through a circular tube. Where,  Turbulent flow is a…

Q: Which one of the following welding processes is suitable to weld bimetallic strips for measuring…

A: Given Bimetallic To find Welding

Q: How can a bore be measured?

A: The inner diameter of any cylindrical device is known as bore. The inner diameter of the cylinder is…

Q: Explain the permanent and temporary reasons for running casing liner inside the hole.

A: permanent and temporary reasons for running casing liner inside the hole.

Q: What two units are used to show the minimum shearstrength of a spot weld?

A: Resistance welding comes in the form of spot welding. One of the simplest and quickest methods of…

Q: Why should convex weld faces be avoided?

A: Excessive Convexity This discontinuity can produce a notch effect in the welded area and,…

Q: what setting needs to be adjusted before welding?

A: Setting needs to be adjusted before welding :-

Q: Why are all welds not inspected to the same level orstandard?

A: Information Provided: Not all welds undergo the same level or standard of inspection. Not all welds…

Q: What is the minimum acceptance criteria for porosity for visual inspection of lap welds?

A: Lap welding: When two metals are attached in a overlapping pattern on top of each other then this…

Q: when making a vertical weld and it appears that the weld metal is going to drip over the shelf, what…

A: In vertical weld, the welding is done from the bottom position to vertically upwards position. In…

Q: ed part are include the unshaded are

A: we will consider donut shaper figure Area = outer circle - inner circle outer circle radius =2…

Q: A soldering iron 'bit' is made of?    A.Brass    B.Tin    C.Steel    D.Copper

A: We can find the answer as below A soldering iron 'bit' is made of?

Q: Question 8 Which ones of the following are NOT Destructive testing benefits. Select three best…

A: Following points are not the benefits of Destructive Techniques.

Q: The suitable terms for the blanks in the statement ."To change from psig to psia , you must ass…

A: There are many different units of measuring pressure. We can use Pascal(Pa). atmospheric(atm), bar,…

Q: After the weld is set up and ready to begin, how mightthe welder want to check for freedom of…

A: Welder method for determine the degree of freedom

Q: What are two common ways to provide for the kerf spacing?

A: Solution: Kerf space is a width of space that is developed in cutting processes when the material is…

Q: What bead pattern is best for overhead welds?

A: Vertical up overhead smaw is best bead pattern for overhead welding. While you're in the vertical…

Q: What is the first weld bead of a multiple pass weld called?

A: Root Pass  is the first weld bead placed in the weld joint in a multi-pass weld.

Q: What is the percentage of rods

A: Given; Determine the percentage of rods whose lengths lie between 438 mm and 441 mm.Where, The…

Q: Answer the following elating to the drawing in figure (38): 1- What is the name of the component? 2-…

A: A rotational or sliding motion for two parts or maybe more or support an applied load is a shaft…

Q: Why is a prototype custom fabricated before producing multiple weldments

A: Why is a prototype custom fabricated before producing multiple weldments

Q: Fill in the blank using R-134a

A: Using property table and P-h chart of R-134a, the required properties are taken.

Q: The largest aluminum tube that should be flared with a double flare has an outside diameter of…

A: The largest aluminum tube that should be flared with a double flare has an outside diameter of

Q: Riser is designed so as to ?

A: Riser is part of gating system in casting process. The gating system includes pour basing, sprew,…

Q: weld is called for by the small triangle on the underside of the welding symbol?

A:

Q: Joining the sheets at specific locations under the heat and pressure is known as Select one: a.…

A:

Q: Who is ultimately responsible for the welder’s safety?

A: Welding is a process in which a large amount of the gasses and heat released if all these are not…

Q: What may happen if the GMA welding electrode is allowedto strike the base metal outside of the…

A: given; What may happen if the GMA welding electrode is allowed to strike the base metal outside of…

Q: How is the removal of the backing strip noted on a welding symbol

A: 4992-2031R AID: 999

Q: facture of twist drills, the shank is joined to the body of

A: GIVEN: In the manufacture of twist drills, the shank is joined to the body of the drill using (a)…

Q: what items need to be turned on before welding

A: The terms to be turned on before welding : 1. Safety: This is the most important factor which should…

Q: In a welding symbol for a u-groove with a consumable insert on the other side. What is the 2 in the…

A: The tail of the welding symbol is used to indicate the welding process as well as its specification…

Q: How long does the metal removal process take?

A: Given data :-  Metal removal process :-  Metal removal processes use a metal cutting tool that moves…

Q: What will be the notation of throat length of a fillet weld

A: Given data⇒ Fillet weld Throat length

Q: Where are the fasteners used?

A: Fasteners are used in industry to disassembled and assembling the products

Q: if a weldment is heated to correct distort from welding, the maximum localized he

A: if a weldment is heated to correct distortion from welding, the maximum localized heat shall not…

Metrology of Screw Threads

Screw threads are a series of ridges having the profile of a helix. This helix profile runs continuously along the length of a uniform solid or a hollow bar of a circular cross-section at periodic intervals. These helix ridges are also formed over a conical bar. These continuous helical ridges are termed threads.