Worn armature bearings can result in higher than normal starter cranking current draw?

Q: An engine may be equipped with all the following belts, except? Select one: a. A serpentine belt b.…

A: Given that An engine may be equipped with all the following belts, except? Select one: a. A…

Q: when adjusting a heavy-duty pull type manual adjusting clutch what is used to compensate for normal…

A: There are two types of clutch adjustment mechanisms: 1) Manually adjusted clutch 2) Self-adjusting…

Q: Cam bearings in OHV engines are typically whichtype?a. Split insertb. Full-roundc. Thrustd. None of…

A: Overhead valve engines are also called pushrod engines. The camshaft of OHV is mounted in the…

Q: True or False: Holding down the <Shift> key during the CHAMFERcommand allows it to draw fillet…

A: By holding the Shift key before selecting the second object when using a CHAMFER command, the…

Q: Name the three drive configurations that a greatset can transfer torque.

A: Given data : Drive configurations

Q: The normal minimal cranking voltage specification isapproximately ___ .a. 9.6 voltsb. 10.5 voltsc.…

A: When starting an engine, the voltage that is available on the starter is known as the cranking…

Q: Which of the following is commonly used as a transmissionneutral start switch?a. Mercuryb.…

A: Given Transmission neutral start switch To find Technology used

Q: Jm Is the motor i

A: Givenη=θmθl=5inertia of motor =Jminertia of link =Jl

Q: motor required?

A: To find power required

Q: Which of the following is not part of the starter motorcircuit?a. Batteryb. Starting safety switchc.…

A: given; Which of the following is not part of the starter motor circuit?

Q: 2. Technician A says that load-carrying ball joints should always have some play in them. Techni-…

A: The ball joints basically serve as the pivot point between the tyre and the suspension in an…

Q: f mechanism?

A: given: bhull engine is the inversion  of which type of mechanism?

Q: Which of the following will be used to control the rotational speed of the generator?

A: Correct Answer is option c)

Q: Technician A says that double-cone synchronizers have friction material on both sides of the…

A: Technician A says that double-cone synchronizers have friction material on both sides of the…

Q: rest position to the upright unstable equilibrium position.

A: Introduction The truck pendulum framework is an ordinary benchmark issue in the control field. It is…

Q: An engine cranks slowly: Technician A says that a possible cause of the problem is poor starter…

A: Given that  An engine cranks slowly: Technician A says that a possible cause of the problem is poor…

Q: What is power transmission?

A: Anwser :- Power Transmission :- In mechanical terms, to transmit the kinetic power from one rotating…

Q: 1750 rpm motor has a 3” pitch diameter drive pulley. It is driving a 9” pitch diameter pulley. What…

A: GivenSpeed of driver pulley ω1=1750rpmdia=3''dia of driving pulley=9''

Q: Which of the following is the best choice when selecting a belt drive to transmit power at a…

A: Introduction: Belt drives are used to transmit and modify the motion while transmitting motion from…

Q: Assume that when the start button is pressed M starter does not energize. List seven possible causes…

A:

Q: What is free gyro?

A: Angular velocity is defined as the change in the angular position of a body following circular…

Q: Technician A checks a starter’s field coils for opensby connecting an ohmmeter between the…

A: Given Starter’s field coils check To find Which technician is or are correct

Q: Which of the following is not part of the starter motor circuit?

A: The  starting system or starter motor circuit used to give initial rotation or crank to the engine…

Q: Compare different types of couplings and their advantages

A: A coupling is a device that is used to hold two shafts together that are different. Coupling is also…

Q: ply to the field. DC motors needed to run ithout any motor being sub

A:

Q: What are the two ways pushrods can be checked for straightness?

A: The pushrods are the connecting link between the rocker arm and the valve lifter. Bent pushrods can…

Q: 4. Describe two type of starting system principles and draw the basic starting circuit

A: The starting system is a combination of mechanical and electrical parts that work together to start…

Q: Industrial Maint. What are the three types of loads that may be placed on a bearing?

A: The three types of loads that may be placed on a bearing are

Q: What are the factor considered in belt drives while transmitting the power from one pulley to next…

A: The transmission of power from one point to another is done by mechanical mechanisms. If the…

Q: Where are the application of slider crank mechanism?

A: This question is based on the concept of slider crank mechanism.

Q: What is an attenuator used for?

A:

Q: At what RPM is the driven pulley in the belt drive system shown rotating? Driver Pulley 6 Inch Dia…

A:

Q: When rope drive is preferred?

A:

Q: .Explain belt driven starters and mention its advantages

A: Belt driven starters A belt driven starter motor system used to start an internal combustion engine.…

Q: Which of the following is probably not the cause of avibrating clutch?a. Excessive crankshaft end…

A: (a) Excessive crankshaft end play is cause of knocking sound when we use clutch. But Vibrating…

Q: How can shift feel be controlled?

A: For many years, accumulators and associated circuits have been the dominant way for regulating…

Q: In V-belt drive, why should the upper wrap angle of small pulley be checked to make it greater than…

A: In V - belt drives , power is transferred between at least two pulley per belt. One pulley drive…

Q: Is minor pulsation a normal condition in typical clutch operation?

A: When the clutch pedal is disengaged ,the movement felt on clutch is known as clutch pulsation.theses…

Q: A normal shaft layout is based on the existıng model as a starter Discuss a process to create a new…

A: A normal shaft layout will contain various components such as bearings, gears and pulleys. But if…

Q: Types of couplings

A:

Q: Explain any one type of coupling which can be used to connect two aluminum alloy shafts when there…

A: Oldham Coupling is used to connect the two shafts which are in lateral misalignment.

Q: What is the alternator to engine drive ratio if alternator turns 1225 rpm when engine is idling at…

A: Since the ratio is 1225 rpm for the alternator: 700 rpm for the engine, 1225: 700         Divide…

Q: Which of the following is not a base Sl unit?

A: Explanation 27 As we know that there are only seven fundamental unit which can we written as 1.…

Q: When the starter spins but does not crank the engine,which of the following may be true?a. Defective…

A: Given Starting problem To find Identify the main problem

Q: Explain the Interruption Cycle with neat sketch

A: The Interruption cycle (also known as the fetch–decode–execute cycle) is the cycle that the…

Q: preload on screws for reused connections is lower than permanent connections Select one: O True O…

A: preload on screws for reused connections ,non-permanent connections is 75 percent of proof load.…

Q: What is the overall height of Tailstock?

A: To Find the overall height of Tailstock?

Q: What is another name for a trigger wheel?   reluctor   interrupter ring   timing wheel…

A: Generally trigger wheel also known as reluctor. The teeth on the trigger wheel equal to the number…