Automotive Technology
7th Edition
ISBN: 9781337794213
Author: ERJAVEC, Jack.
Publisher: Cengage,
expand_more
expand_more
format_list_bulleted
Concept explainers
Question
Chapter 18, Problem 5MC
To determine
The minimum cranking voltage according to the specification.
Expert Solution & Answer
Trending nowThis is a popular solution!
Students have asked these similar questions
The normal minimal cranking voltage specification isapproximately ___ .a. 9.6 voltsb. 10.5 voltsc. 11.0 voltsd. 12.65 volts
Worn armature bearings can result in higher than normal starter cranking current draw?
Which of the following is commonly used as a transmissionneutral start switch?a. Mercuryb. Momentaryc. MPMTd. SPST
Chapter 18 Solutions
Automotive Technology
Ch. 18 - Prob. 1SACh. 18 - Prob. 2SACh. 18 - The part of the armature that the brushes ride on...Ch. 18 - Describe how to perform a starter bench test.Ch. 18 - True or False? The strength of the magnetic field...Ch. 18 - True or False? Worn armature bearings can result...Ch. 18 - Which of the following is not part of the starter...Ch. 18 - Which of the following tests would not be...Ch. 18 - When the starter spins but does not crank the...Ch. 18 - If the solenoid clicks while trying to crank the...
Ch. 18 - Prob. 5MCCh. 18 - Prob. 6MCCh. 18 - Prob. 7MCCh. 18 - The device that prevents the engine from turning...Ch. 18 - A control circuit voltage drop test shows a 1.1...Ch. 18 - An engine cranks slowly: Technician A says that a...Ch. 18 - Prob. 2ASRQCh. 18 - Pinion gear-to-flywheel ring gear clearance is...Ch. 18 - Technician A says that a starter no-load test is...Ch. 18 - Cranking current is excessive but is normal when...Ch. 18 - Prob. 6ASRQCh. 18 - When diagnosing a no-crank no-start condition, no...Ch. 18 - While discussing a no-crank condition: Technician...Ch. 18 - Prob. 9ASRQCh. 18 - While discussing electric motors: Technician A...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- If the solenoid clicks while trying to crank the engine with the starter, which of the following is not a probable cause? A faulty neutral safety switch Low battery voltage Low voltage available to the solenoid An open in the hold-in windingarrow_forwardWhen the starter spins but does not crank the engine, which of the following may be true? Defective starter relay Damaged flywheel teeth A faulty starter solenoid All of the abovearrow_forwardWhat is a 100% shutoff system?arrow_forward
- While discussing secondary voltage: Technician A says that the normal required secondary voltage is higher at idle speed than at wide open throttle conditions. Technician B says that the maximum available secondary voltage must always exceed the normally required secondary voltage. Who is correct?arrow_forwardWhen the starter spins but does not crank the engine,which of the following may be true?a. Defective starter relayb. Damaged flywheel teethc. A faulty starter solenoidd. All of the abovearrow_forwardDiscuss the method of obtaining pressure crank angle diagram. List down the parameters that can bestudied from the pressure crank angle diagram.arrow_forward
- A control circuit voltage drop test shows a 1.1 volt drop at the starter S terminal. Which of the following could be the cause? High resistance in the solenoid switch circuit High resistance in the clutch safety switch Loose battery cable connection Short in the starter armature windingsarrow_forwardExplain why controlling the rotor current also controls the stator current.arrow_forwardWhen diagnosing a no-crank no-start condition, no voltage is present at the S terminal of the solenoid while attempting to crank the engine. Technician A says a faulty starter motor is the cause. Technician B says a shorted safety switch is the cause. Who is correct? Technician A Technician B Both A and B Neither A nor Barrow_forward
- Which term refers to variations in thickness of the rotor? Torque Lateral runout Parallelism Pedal pulsationarrow_forwardWhile discussing a no-crank condition: Technician A says to verify the condition of the batten' before testing the starter motor Technician B says a scan tool may be used to check starter control circuit operation. Who is correct? Technician A Technician B Both A and B Neither A nor Barrow_forwardThe two types of motors used for hermetic compressorsare _________ and _________.arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Automotive Technology: A Systems Approach (MindTa...Mechanical EngineeringISBN:9781133612315Author:Jack Erjavec, Rob ThompsonPublisher:Cengage LearningUnderstanding Motor ControlsMechanical EngineeringISBN:9781337798686Author:Stephen L. HermanPublisher:Delmar Cengage LearningRefrigeration and Air Conditioning Technology (Mi...Mechanical EngineeringISBN:9781305578296Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill JohnsonPublisher:Cengage Learning
- Welding: Principles and Applications (MindTap Cou...Mechanical EngineeringISBN:9781305494695Author:Larry JeffusPublisher:Cengage Learning
Automotive Technology: A Systems Approach (MindTa...
Mechanical Engineering
ISBN:9781133612315
Author:Jack Erjavec, Rob Thompson
Publisher:Cengage Learning
Understanding Motor Controls
Mechanical Engineering
ISBN:9781337798686
Author:Stephen L. Herman
Publisher:Delmar Cengage Learning
Refrigeration and Air Conditioning Technology (Mi...
Mechanical Engineering
ISBN:9781305578296
Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson
Publisher:Cengage Learning
Welding: Principles and Applications (MindTap Cou...
Mechanical Engineering
ISBN:9781305494695
Author:Larry Jeffus
Publisher:Cengage Learning