Determine the three forces acting on the plate that are equivalent to the force R = 210k kN.

Q: Calculate the allowable force for a 14 gage (.0641" dia) bicycle spoke, if the stress should not exc...

A: Given information: The gauge of the spoke = 14 gauge  which implies the diameter of the spoke is (d)...

Q: A decorative fountain for a casino is designed to shoot a stream of water straight up in the air.  F...

A: given: inlet diameter of nozzle=4in outlet diameter of nozzle=2in height of stream=43 feet

Q: Construct the bending moment (M) and shearing force diagram for the beam dimensions

A:

Q: i) The Alaska pipeline conveys crude oil 800 miles across the state of Alaska from Prudhoe Bay to Va...

A: Data given -  L = 800 miles = 800×5280 ft  di = 48 inch = 4ft  t = 0.5 inch  Outer diameter of steel...

Q: - Find the magnitude of the resultant force (in kN). - Find the distance (in m) that would yield the...

A: The magnitude of the first force is, F1=4 kN. The magnitude of the second force is, F2=3 kN. The mag...

Q: If F = 120 N applies to the curved beam, determine the moment of this forceabout points O and B

A: given If F = 120 N applies to the curved beam, determine the moment of this forceabout points O and ...

Q: Q 152. quick tests to a GM hot film mass airflow meter on an engine with idling problems are being p...

A: Hot film sensor The hot-film sensor is used for the indication of mass airflow entering the engine. ...

Q: 7. The beam ABC, built into the wall at A and supported by a cable at C, carries a distributed load ...

A:

Q: A silicon carbide ball with 5 mm in diameter has volume based CLTE (a,) of 8.1 x106/°C. If the ball ...

A:

Q: Q 144. IAC motor damage may result if throttle body cleaner is allowed to enter the motor. T F

A: IAC motor damage may result if throttle body cleaner is allowed to enter the motor.  

Q: what does I.B.C stand for in relation to diesel engines

A: In relation to the diesel engines IBC stands for inverted Bryton cycle. This concept has been develo...

Q: 4. For the braced beam and loading shown; (a) draw free body diagram, (b) determine the magnitude fo...

A:

Q: An unknown gas (with PVT conditions of; 101 kPa, 2.83 m3 & 23°C) is to be transferred into a sto...

A: R = 8.314 J/mol·K (universal gas constant)for the 1st Gas : P1=101 kPa , V1=2.83 m3, T1=23o C+273=29...

Q: Consider the loaded beam and the shear force diagram: what is the location of the max bending moment...

A: Given Data: The concentrated load is P1 = 10 kN. The rectangular load is w = 5 kN/m. The free-body...

Q: need help with this, and a force diagram if needed

A:  

Q: A simply supported truss is shown below. There is a pin support at A anda roller support at D. Deter...

A:

Q: Which of the following statements are true about the intent of a regenerator in a Brayton cycle? Sel...

A: given:

Q: How long would it have to be in order for a soundwave traveling at 343 m/s to resonate at 440Hz in t...

A:

Q: The box having mass of m is being pulled by a motor. Initial velocity of the box is v0. Motor pulles...

A: Given: The initial velocity of the box is v0. The expression for the force is F=500s+550. The dista...

Q: It takes 15s to raise a 1200-kg car and the supporting 300-kg hydraulic car-lift platform to a heigh...

A: Given The mass of the car is M=1200 kg. The mass of the hydraulic lift platform is m=300 kg. The ti...

Q: A tube of 0.0G metrar, nuas into a tanth under pressune. The tube incl. des a abrupt The minor loss ...

A: Given data: - The diameter of the tube is d = 0.06 m. The minor loss coefficient is hL = 6.8. The f...

Q: A vapour compression plant uses R-12 and is to develop 5 tonnes of refrigeration. The condenser and ...

A: Given data: R.E = 5 tonnes  (R-12 refrigerant)                    Condenser temperature = 40°C      ...

Q: a = 4 ft b = 3 ft C = 2 ft d = 2.5 ft F1 = {-25i+20j+35k} lb F2 = {-12i-28j+40k} lb y F1 Find the y-...

A: Find the position vector for the tail of the vector. Write the F2 vector  

Q: 17) A chamber contains a gas at a temperature of 300 K. At some moment half of the gas is released f...

A: Thermal energy of a gas is proportional to the number of gas molecules and its temperature. Now when...

Q: what is the meaning N14 in the N14 cummins engine

A: Solution:

Q: theta - 33 degrees M1 - 450 Nm M2 = 550 Nm M3 - 650 Nm M3 M2 M

A: M1=450 N-mM2=550 N-mM3=650 N-mθ=33°  

Q: Write legibly 6. The piping shown in the figure is a parallel-pipe system carrying water at normal t...

A:   Given: Q=0.35 m3/sPipe A→lA=4000 m, dA=0.3 mPipe B→lB=2500 m, dB=0.35 mPipe C→lC=3000 m, dC=0.2 m

Q: q 146. its impossible to visually check the spray pattern and volume of port system injectors. T F

A: Its impossible to visually check the spray pattern and volume of port system injectors.

Q: A square block has 320 mm bottom sides dimensions, weighing W is 1.4 kN on an edge slides down an in...

A: Given data: The bottom side, a = 320 mm. The weight of the block, W = 1.4 kN. The incline angle, θ=...

Q: A spinning top consists of a ring (which can be treated as a cylindrical shell) of mass m = 0.52 kg ...

A: Draw the FBD for the given question:

Q: A spring having original length of L1 is constricted by the 4 cords having length of L2. So, those c...

A:

Q: Water falls vertically downward from an open faucet with an initial velocity of 47 cm/s. If the stre...

A:

Q: A stepped circular bar having diameters of 20 mm, 15 mm, and 10 mm over axial lengths of 100 mm, 80 ...

A:

Q: Can you help me solve this question?

A: Given The differential height of manometer is h=5 cm. The density of mercury is ρHg=13600 kg/m3. Th...

Q: Explanation about Vibration isolation, transmissibility, Magnification factor

A:  It is very well known that many kinds of vibrations are not desirable and thus must be removed from...

Q: Need help with c , d and e please

A:    

Q: Calculate the maximum tensile stress developed in a 1/4-20 bolt (Major dia = 0.2500" and Root dia = ...

A: Write the given data with suitable variables: P=426 lbdmin=0.1959 in