Which cutting process does not produce a kerf space

Q: What is the major benefit of cutting fluids that contain water?

A: Cutting fluids: These are the special type of lubricant and coolant used in the manufacturing…

Q: W hat are the consequences if a cutting tool chips?

A: Consequences if a cutting tool chips  this is related to chip formation. the chips are formed due to…

Q: What is cutting tool? 2. What are the cutting tool material? 3. Types of cutting tool. 4. Cutting…

A: “Since you have posted a question with multiple sub-parts, we will solve first three subparts for…

Q: e parameters of cutting process?

A: Parameters of cutting process ( With unit)

Q: Which would you use for any of the following situations: Cutting on a smaller mill, a larger mill…

A: Given data: For cutting a smaller mill  A larger mill with little clearance A smaller diameter…

Q: An aluminum hollow shaft 200 mm outside diameter, 100 mm inside diameter and 500 mm length from…

A: Givenoutside dia=200mminside dia=100mmL=500MMN=400rpmfeed rate=0.25mm/rev

Q: Differentiate the Branch and Bound Method and Gomory's Cutting Plane Method.

A: given; Differentiate the Branch and Bound Method and Gomory's Cutting Plane Method.

Q: (4):- The surface of the product is smooth as the cutting speed is a---- a- High speed b- Low speed…

A: 4) Option A  => High Speed   ===>>>  Which it gives the best surface finish. 5) Option A…

Q: Write down the important properties of cutting tool?Write short note on4different types of cutting…

A: A machine tool, also known as a metal cutting tool, is used to machine metal components for…

Q: Which formula is used for calculation of specific cutting pressure?

A:

Q: Calculate the time required to make a ravage cut, at a feed rate of 0.015in. on a piece of machine…

A: Given:L=18 ind=2 infn=0.015 in/sec

Q: What are various cutting technologies.

A: GIVEN: What are various cutting technologies.

Q: Choose TWO (2) types of cutting processes for cutting thin metal (sheet metal)

A:

Q: The angle on a single-point cutting tool geometry in which the face of a tool is inclined sideways…

A: Back rake angle: It is the inclination of the face toward or away from the end or the end cutting…

Q: 6) Why are most broaches made from alloy or high-speed steel rather than from tungsten carbide. 7)…

A: Given questions: 6) Why are most broaches made from alloy or high-speed steel rather than from…

Q: Determine friction angle for metal cutting operation

A: To find Friction angle.

Q: Which of the following best describes the "cutting plane" of aligned sectional view: It is a…

A: it is a combination of parallel cutting planes

Q: 1. Write down the important properties of cutting tool? Write short note on 4 different types of…

A: Dear student, there are two different questions in the single question and we are suppose to solve…

Q: In a multi point cutting tool the negative rake angle is used for high tensile strength materials.…

A: Positive rake angle used for ductile or soft material while negative rake angle used for higher…

Q: An aluminum hollow shaft 200 mm outside diameter, 100 mm inside diameter and 500 mm length from…

A: Given data as per question The outside diameter of shaft =200 mm Inside diameter =100 mm Length of…

Q: 20)When a thick material is to be cut by WJC, one should prefer

A: All of these is correct according to given question for thick material so  Option d is absolutely…

Q: 22.33 In Table 22.1, the last tw o properties listed can be

A: The general characteristics of tool materials is given.

Q: the ratio of new tool life to original tool life

A: Given, n=0.5 if cutting speed is reduced by 50 % Then find the ratio of new tool life ?

Q: 22.6 List the major functions of cutting fluids.

A: The  major purpose of cutting fluids is to carry away the heat generated during machining operation.

Q: Broaching is an example of joining process primary shaping process surface finishing process…

A: Broaching is an multiple tooth cutting operation with the tool reciprocating. It is an fastest way…

Q: Cold Circular saws are capable of making cuts accurate to what tolerance?

A: Cold circular saws The instrument used in cutting ferrous and non-ferrous alloys material is known…

Q: Explain the importance of each angle in metal cutting with neat sketch

A: There are basically three angles that need to be focused on during the metal cutting operation.…

Q: 10. Formula for cutting speed of the shaper, tell the meaning of each variables.

A: SHAPER In shaping, the cutting tool is held in the tool post located in the ram, which reciprocates…

Q: Why must a band saw blade be annealed after welding?

A: Given Data : Band saw blade

Q: Aluminum bar with 100mm diameter and 500mm long is turned down to 88mm diameter, using two passes on…

A:

Q: Define the fundamental of cutting.

A: Definition of Cutting : Cutting is defined as It's process which creates new surfaces in a solid by…

Q: ENUMERATE THE STEPS IN CUTTING AND PIECING A PLATE USING GAS CUTTING

A:

Q: Which one of the given options is wrong?         a)A curvy surface is created in shaping process…

A:

Q: In a dry cutting operation using a -5 degree rake angle, the measured forces were; cutting force =…

A: Consider Fc and Ft be the cutting force and feed force respectively during an machining operation…

Q: Tool design What are some of the typical considerations for each one of the following metal cutting…

A: Metal cutting Process It is the process to remove unwanted material in the form of chips from the…

Q: Excessive temperature at the cutting tool point will lead to the following: Brittle fracture ، All…

A: Excessive temperature at the cutting tool point is very dangerous.

Q: Friction less cannot be with cutting surfaces. * True O False Extrudina does not

A: 1.Friction less cannot be with cutting surfaces False When the cut surface is not flat frictionless…

Q: What type of saw consists of a continuous band of metal with cutting teeth on one edge?

A: Given Saw consists of a continuous band of metal with cutting teeth on one edge To find Identify the…

Q: Orthogonal cutting is dimensional metal cutting

A: Orthogonal cutting is ____________ dimensional metal cutting. Answer: a. two

Q: Increasing the entering angle of the tool affects the vibrations during cutting by:

A: Entering angle is the angle between the leading cutting edge of the tool and surface of the…

Q: Q3:- Choose the Correct answer. (1):- The drilling tool must be with a- High hardness b- Low…

A:

Q: How nuch machlning time required a mild steel rod trom 65mm 58 mm over a length of 100 mm by turning…

A: Given Data ⇒ Initial Diameter of mild steel rod (D)=65 mm Length(L)=100 mm Approach Length(A)=5 mm…

Q: Which of the following is the example of cutting shaping process? O Pressing Forging

A: given

Machining Processes and Machine Tools

Machining is represented as the process in which an excessive amount of substance is eliminated from the particular element in the form of pieces. In machining, cutting tools such as rotary tools, lathe, drill press, grinder, chop saw, welders, and many more are applied to get the desired shape. As compared to other manufacturing processes, machining is precise and versatile.