Concept explainers
A balanced V load having a 10
a. the phase voltage of the generator.
b. the phase voltage of the load.
c. the phase current of the load.
d. the line current.
(a)
Phase voltage of generator.
Answer to Problem 1P
The phase voltage of generator is
Explanation of Solution
Given:
Resistance in each leg of
Line voltage of generator is
Concept used:
Write the expression for phase voltage of the generator.
Here,
Calculation:
Substitute
Conclusion:
Thus, phase voltage of generator is
(b)
Phase voltage of load.
Answer to Problem 1P
The value of Phase voltage of load is
Explanation of Solution
Calculation:
As each phase of
So value of Phase voltage of load is
Conclusion:
Thus, value of Phase voltage of load is
(c)
Phase current of load.
Answer to Problem 1P
The phase current of load is
Explanation of Solution
Concept used:
Write the expression for phase current of load.
Here,
Calculation:
Substitute
Conclusion:
Thus, phase current of load is
(d)
Value of line current.
Answer to Problem 1P
The value of line current is
Explanation of Solution
Calculation:
Value of line current is equal to value of phase current in
As load is
Conclusion:
Thus, value of line current is
Want to see more full solutions like this?
Chapter 24 Solutions
EBK INTRODUCTORY CIRCUIT ANALYSIS
Additional Engineering Textbook Solutions
Electric Circuits (10th Edition)
Electronics Fundamentals: Circuits, Devices & Applications
Electric Motors and Control Systems
ANALYSIS+DESIGN OF LINEAR CIRCUITS(LL)
Fundamentals of Applied Electromagnetics (7th Edition)
Principles and Applications of Electrical Engineering
- A balanced star load with impedances of 6∟45o ohms is connected to a three-phase, four-wire, 208 volt, ABC system. Find the line currents, the neutral current, the power per phase and the total power (S, P, Q).arrow_forwardNon-Reactive Loads of 10kW, 20kW and 12kW are connected between the neutral and the red, yellow and blue phases respectively of 3-phase, 4 wire . The line voltage is 400. If a three phase motor is now started ,taking 150 A from the lines at a power factor of 0.3 lagging What should be the total current in each line and the neutral wire? Find the total real and reactive power supplied to the loadsarrow_forward1. Solve the following problem: A THREE-PHASE CIRCUIT WHERE THE BALANCED DELTA LOAD OF 36 + J54 OHMS IS SUPPLIED BY 8,602 OHMS IMPEDANCE CONDUCTORS WITH A PHASE ANGLE OF 54,462 DEGREES. IF THE GENERATOR VOLTAGE IN PHASE B IS 100 VOLTS ANGLE - 120 DEGREES. CALCULATE: A) THE VOLTAGE BC IN LOAD. B) THE POWERS IN THE CONDUCTORS. C) THE POWER TRIANGLE IN THE LOAD.arrow_forward
- A three phase transmission line has a resistance of 10 Ω and reactance of 80 Ω per wire. The load current is 90 A and the power factor of the load is 80% lagging. The sending (generator) end voltage in the line is 44,000 V line to line. What is the receiving end voltage? a. 38.4 kV b. 34.3 kV c. 41.2 kV d. 42.3 kVarrow_forwardering questions and answers /... Question: Two wattmeters in a 3 phase, 3-wire system with a effective line voltage of 120V read 1500W and 500w then inpedence in a balanced delta connectionarrow_forwardA current is measured at the neutral ground of a star load, of equal impedances in all three phases. Which of the following conditions is NOT possible?A) The currents in the three phases are equal in magnitude and angle.B)One phase of the supply conductors was left in open circuit.C) The line-to-neutral voltages in the load are equal in magnitude and with 120° phase shifts between them.D) None of the abovearrow_forward
- Two wattmeters are connected to a 3 phase, 3 wire positive sequence system with a 100 Voutput supplies a balanced delta connected load with impedance of 20 cis 40°. Calculate the: (a) Phase and Line currents(b) Readings of the two Wattmeter(c) Draw the Phasor diagram of the currentsarrow_forwardA balanced 3 phase star connected load draws power from a 420 V supply. Two wattmeter's indicate 9200 W and 3800 W respectively, when connected to measure the input power of the load, the reverse switch being operated on the meter indicating the 3800 W reading Find the following: The Input power, P= The power factor, cosɸ= The line current, IL=arrow_forwardA balanced Y - connected load having a 25 Ω resistance in each leg is connected to a three -phase , four wires, Y-connected ABC sequence AC generator, if the line volatge EAB=, calculate 1. The phase voltages of the generator 2. The phase voltages of the load 3. The phase currents of the load 4. The line currentsarrow_forward
- The power input to a three-phase motor is measured by the two wattmeter method. The three line voltages are 220 V and the current in each of the three line wires is 8 A. If the three-phase power factor is 0.866 lag, what are the values of power indicated by wattmeter 1 and wattmeter 2arrow_forward1. Calculate the line currents for phase a, b and c.2. Calculate the line to neutral voltages at the load for phase A, B and C.3. Draw the phasor diagram of the source phase voltages and currents.arrow_forwardA 210V, 50 Hz, single phase radial distribution system, the resistance of the wire is 0.0008 ohm/m supply and return. Two loads are connected and it consumes 20 and 15 A respectively and are fed from the cable at distance of 25 and 10 respectively. Calculate the voltage available across load 1 and 2. a- Voltage across load A is, Va= b- Voltage across load B is, Vb=arrow_forward
- Power System Analysis and Design (MindTap Course ...Electrical EngineeringISBN:9781305632134Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. SarmaPublisher:Cengage Learning