No Go holes and H7/p6 tolerances Question 2For a 10 H7/p6 fit: Complete the following table.HoleShaftTolerance:Tolerance:Limit deviationsUpper deviation (ES):Lower deviation (EI):Upper deviation (ES):Lower deviation (EI):Limit of sizeMaximum limit of size:Minimum limit of size:Maximum limit of size:Minimum limit of size:FITType of Fit:Мах.......Mini....Go-No GO Gages for the above HoleComplete the following table.Show your calculation and draw Go -Not Go representation.Go Plug GageNOT Go Plug GageNominal size:Nominal size:Tolerance:Tolerance:Class:Class:Max limit of size:Max limit of size:Min limit of size:Min limit of size:

10 H7/p6 Hole dimensions from a standard tolerance chart for 10mm H7 tolerance is +15 therefore…

Answered: No Go holes and H7/p6 tolerances

Engineering

Mechanical Engineering

No Go holes and H7/p6 tolerances

Automotive Technology: A Systems Approach (MindTap Course List)

6th Edition

ISBN:9781133612315

Author:Jack Erjavec, Rob Thompson

Publisher:Jack Erjavec, Rob Thompson

Chapter34: Emission Control Diagnosis And Service

Section: Chapter Questions

Problem 5RQ: Explain why the I/M 240 and similar tests are being replaced by the OBD II system test.

See similar textbooks

Related questions

Q: 14. What size internal chamfer is required for the part? 14. 15. Why does the flatness tolerance not…

A: 15. Why does the flatness tolerance not reference a datum

Q: (C) STEP REAMER (D) BULLET REAMER (E) STRAIGHT REAMER (F) PLOTED REAMER 2004 DERSTANDING GAUGE 1.…

A: HL18-6HL- Pin basic part number18-PartII, class 2 cadmium plate

Q: What type of geometric tolerances have no datum features? Profile Tolerances All Tolerances O…

A: Geometrical Tolerancing: The tolerances in any system which allows tolerances to be applied…

Q: Tell us about the tolerance zone in operations.

A: As per given we have to detail describes about tolerance

Q: 4X .250-20 UNC-2B 1.260±.010 .984±.010 2.600 ø2.012 2.008 Ø 3.350

A: the position tolerance for the diameter hole 2.012/2.008 and the diameter stud 2.006/2.002 position…

Q: Q13) For the following micrometer: a- What is the part diameter?

A: 13

Q: Fixing a wheel barrow takes a specific diameter axel of 2.50 inches. Thankfully, the manufacture…

A: It is given that the axle required for fixing the wheel barrow should have a diameter of 2.50…

Q: Refer to the Ø.8740 ± .0005 dimension. D) What is the MMC,(Maximum material condition) ?…

A: D) Calculate the maximum material condition (MMC).

Q: In transition fit, tolerance zone of hole is entirely above that of shaft tolerance zones of hole…

Q: 3. a) For an interference fit the hole is smaller than the shaft (True/False) (0.5 Mark) b) The…

Q: the case where circular runout has been applied to an end face of a shaft, the following is…

A: Since the circular runout provides both concentricity and circularity with inherent influence. It…

Q: Calculate the dimensions of shaft and hole for assembly condition specified as ø50H7/d9. Identify…

A: The allowance is defined as the difference of maximum material limits of hole and shaft .

Q: Name TWO (2) types of hardness test.

A: Hardness test- the hardness test is perform to know the hardness of material.it is used to determine…

Q: A

A: Given : The tolerance off hole = 0.5

Q: Unilateral Tolerance is Total tolerance is in both the directions May or may not be in any direction…

A: Unilateral tolerance is the type of tolerance in which true profile is only permitted in one…

Q: What is the philosophy of the Go and No-Gogauging? Complete any missing information on part 182 and…

A: PHILOSOPHY OF GO & NO GO GAUGING:- 1.GO end gauging :- Go end used in qualify the…

Q: Refer to the 1.914 dimension. B) What is its tolerance ? ________________________________ C) What…

A: Tolerance for the given dimension is 0.01. now as tolerance = upper limit - lower limit. and we also…

Q: (USCS units) A GO/NO-GO plug gage is needed to inspect a 1.000 ± 0.020 in diameter hole. A wear…

Q: The diameters of hole with a nominal size Ø115 must be within limits Dmax = 115.015 mm and Dmin =…

A: Given:D=115 mmDmax=115.015 mmDmin=114.982 mm

Q: Find the tolerance and fit type of Ø 60 H7k6,

A: given: nominal size, D=60mm tolerance hub: H7 tolerance shaft: k6 so for tolerance hub: H7, the…

Q: Refer to the 1.914 dimension. A) Where is the tolerance specified ?…

A: A) For MMC & LMC Consider ϕ0.8740±0.0005 MMC=0.8740+0.0005=ϕ0.8745 LMC=0.8740-0.0005= ϕ0.8735…

Q: 3. If the tolerance applies at MMC then a possible O indeterminant bonus O LMC zero tolerance…

A: given = fill in the blanks

Q: Explain the purpose of the v-notch on the specimen for Charpy Test.

A: Charpy test: The Charpy test is also known as Charpy V-notch test for toughness of material. Charpy…

Q: If the basic diameter of shaft is 20mm with -0.02mm unilateral tolerance, and diameter of hole is…

A: We have to determine what kind of fit is achieved?

Q: Fill out the table for a .25 basic hole with an LN1 fit Shaft Hole Limits Basic Size Tolerance MMC…

A: Given Data:

Q: Define the various types of fits? Also define fits in terms of shaft and hole basis system

A: Fits is defined as a term that is widely used in manufacturing engineering. It is the assembly…

Q: What are the geometry features in the picture below? Indicate main geometry and tolerances

A: Geometry Features which mentioned in the Drawing are as below:

Q: Position tolerances applied to features that result in a fixed fastener condition usually require…

A: Position tolerance applied to feature that result in a fixed fastener condition usually require 1)…

Q: All form tolerances are surface controls except for Form tolerances are independent of all other and

A: Form tolerance is a used to determine the form of the part. It refers to the limitation of a form…

Q: Refer to the Ø.750 dimension. A) Where is the tolerance specified ?…

A: 1—position 2 – the shape of the tolerance zone

Q: 8) __________ notched specimens are used for Charpy impact test. Select one: V U & V U Key hole

A: V notched specimens are used for charpy impact test

Q: I am going to use a Bolt through the .41 DIA holes to align the parts, answer the following: What…

Q: Is the 'fit' between the 2 parts shown below a clearance fit or interference fit?

Q: how do you write this in a feature control frame? "The cross-sectional shape of this feature must be…

A: The feature control frame is required to describe the condition and tolerances of the geometric…

Q: Which type of feature doesn't belong to orientation tolerances? Concentricity…

A: using datum plane measure the Angularity , Perpendicularity and Parallelism

Q: 7. What is a tolerance?

A: Measurement: It is the numerical quantification of the body or event that is used to compare with…

Q: Cold circular saws are capable of making cuts accurate to what tolerance Multiple Choice (select the…

Q: What tolerance is specified for the width of the groove?

A: Given :- Bolt Drawing Find :- Tolerance of the width of the drawing

Q: • Calculate the input torque acting on the manual crank assuming an înput force sqlt to • Ca lculate…

A: given ; ⇒input force(F1)=7lbs⇒diameter of hole (D)=12in⇒coefficient of friction(μ)=0.13⇒crank…

Q: state the functions of interference fit and draw it on illustration of size tolerance zone .

Q: Show the steps and calculations to determine one type of fit. Diameter of ball bearing hole is =…

Q: e allowable position tolerance that may be applied to each part in a

A: Determine The applied allowable position tolerance

Q: Refer to the Ø.8740 ± .0005 dimension. A) Where is the tolerance specified ?…

A: Hello. Since your question has multiple sub-parts, we will solve first three sub-parts for you. If…

Q: I need help with numbers 4 and 7. They are both wrong. One the part attached what is the maximum…

Q: ACTIVITY 10-1 Split Type Dowel 1. 1. Which part has the longest length? 2. Which part has the…

A: Given The drawing of CHART DOWEL SPLIT TYPE TO SOLVE 4.; 5.; 6.

Q: The line used to show where a section view is cut is called A. a section line B. a hatch line…

A: An engineering drawing is a type of technical drawing which is used by thee industries to convey…

Q: Bilateral tolerance is Total tolerance is in 1 direction only Total tolerance is in both the…

A: As per our guidelines we are supposed to answer first one .Kindly repost other question as a…

Q: 1. Is the 'fit' between the 2 parts shown below a clearance fit or interference fit ? 2. Which…

Concept explainers

Limits, Fits, and Tolerances

The maximum or minimum allowable sizes within which the size of component lies are known as limits. The limits are classified into two types:

Question

No Go holes and H7/p6 tolerances

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Generally, final design results are rounded to or fixed to three digits because the given data cannot justify a greater display. In addition, prefixes should be selected so as to limit number strings to no more than four digits to the left of the decimal point. Using these rules, as well as those for the choice of prefixes, solve for σ. σ = M/Z, where M = 1 770 lbf-in and Z = 0.934 in³. (type the value and the unit ex. 1.00psi)
Two machines are currently in use in a process at a local manufacturing plant. The standards for this process are LSL = .400 and USL=.403. Machine One is currently producing with mean =.401 and a standard deviation= .0004. Machine Two is currently producing with mean = .4015 and a standard deviation = .0005. Which of the two machines is capable based on the capability index?
25000 bolts are going to be used to fix a certain structure. The bolts have a mean fatigue life of 10000 days with a standard deviation of 2000 days under heavy dynamic loading conditions.What is the probability that a bolt will fail between 8250 and 12500 days of use?
Hide AnswerTry Another The formula for piston displacement is P = cd2SN, where c is a constant, d is the cylinder bore, S is the stroke, and N is the number of cylinders. For c = 0.7854, d = 3.000, S = 4, and N = 6, find the piston displacement. (Use the rules for working with measurements to give your answer to the appropriate accuracy and/or precision. Note: The values for S and N are exact numbers. Ignore exact numbers when determining the appropriate accuracy and/or precision.)
For the following statements, answer True or False and explain the answer briefly. The tolerance of standard mass used must be smaller than the uncertainty of analytical balance to be calibrated.
Determine the limits of sizes, tolerances and fundamental deviations for the shaft designated as 40 H8 / f7 use fundemental deviation for shaft f7, es=-5.5(D)0.41
(a) A very important component of a system has a mean time between failures of 100 hr and a mean time to repair of 10 hr. Determine the inherent availability of the system. (b) If the equipment in Q7 (c i) above is required to meet an inherent availability requirement of 0.985 and a mean time between failures of 100 hr. Calculate the permissible mean time to repair and if the system as a mean of the time intervals between corrective maintenance actions of 900 hrs and the sum of the mean corrective maintenance time intervals including supply downtime and administrative down time of 10 hrs Determine the operational availability of the system
Explain why the I/M 240 and similar tests are being replaced by the OBD II system test.
Calculate the average fall time and standard deviation using the data above. Average - 1.5s Stdev- 1.85s Use the average fall time and one of the kinematic equations to determine the height of the building. Add the standard deviation from step 1 to the average fall time from step 2. This represents a “maximum fall time.” Use this time to calculate the “maximum” height of the building.
Complete the conversions to the appropriate number of sig figs. Show work and use the conversion factors supplied.
Bearing used in an automotive application has a nominal inside diameter of 3.81 is expected to be cm.A random sample of 25 bearings is selected andaverage inner diameter of bearing3.8037 cm. exists as. bearing inner diameter σ=0.03 cm Standard deviation ofis known to be normally distributed. α=0.01 ; a) Test whether the bearing used has a nominal inside diameter of 3.81 cm. b) How to answer the question in part (a) by constructing a two-sided confidence interval on the mean diameter?explain that you can answer note: can you write the solutions legibly.
16- Brinell harness experiment is a type of NDT test. Select one: True False