List six steps involved in performing a visual inspection.

Q: The type maintenance requires periodical inspection and testing.

A: Preventive maintenance/periodic maintenance/ planned maintenance is driven by time, meter or event…

Q: Distinguish between “interference fit” and “Clearance fit”.

A: Clearance fit- It occurs when two tolerance parts will always leave a space or clearance when…

Q: with procedure please, Thank you!!

A:

Q: Explain different types of methods and procedure of inspection of bearing on workshop machines

A: BEARING A bearing is a machine element that only reduces relative motion and friction between moving…

Q: 18 - Which of the following is not one of the error sources that can affect the measurement results?

A: Correct option:  D. The operator who will carry out the measurement should not have any physical…

Q: why universal testing machine important (3-5 sentence ONLY)

A:

Q: a) Briefly explain the advantages of hammer test over shaker test in modal testing.

A:

Q: Explain the objective of (ECT) Visual Inspection.

A: Much of our knowledge about sensory processing in the brain is based onquasi-linear models and the…

Q: Particle

A: GIVEN: Explain the principle of working and operation of Magnetic Particle Inspection with…

Q: Explain the principle of working and operation of Dye Penetration Technique Inspection with neat…

A: Dye Penetrant Inspection (DPI) is widely used to detect surface breaking flaws.   This…

Q: With reference to the drawing callout in figure 5 below, which part(s) would 'pass' or 'fail' along…

A: Data given-  Dimensions of standard size  0.25±0.01 So tolerance is equal to 0.02  And the upper…

Q: Name TWO (2) types of hardness test.

A: Hardness test- the hardness test is perform to know the hardness of material.it is used to determine…

Q: Draw the iso metric and front view

A: Given : Top and right side view  Sketch : front and isometric view

Q: List the important information that should be considered in planning a reliability test programme.

A: Steps are given in next step.

Q: (USCS units) A GO/NO-GO plug gage is needed to inspect a 1.000 ± 0.020 in diameter hole. A wear…

A:

Q: briefly describe what the impact test practice consists of and what is its purpose? PLEASE I NEED IT…

A: Impact test=The purpose of this test measures the amount of energy absorbed by a material during…

Q: how you apply safety in our shop?

A: Importance of Shop Safety : It is necessary to keep environment safely for employees and workers to…

Q: Penetrant testing Procedure below with Dwell time, and Minimum three defect that can be detected…

A:

Q: How can the inspections and tests be made promptly andtimely by the Inspector?

A: The need to perform inspections as regular is to ensure the proper working of all the industry…

Q: the following is not true regarding optical comparator? All of them are true b. High magnification…

A: Comparators are used to determine the difference in dimensions between a given component and a…

Q: Which type of feature doesn't belong to form tolerances? Circularity The profile of a surface…

A: As we know principle component of form tolerence are Straightness.Flatness.Roundness.Cylindricity.

Q: a) Define what is meant by "surface finish" and describe 2 ways in which it should be specified on…

A: Surface finish The smoothness of the material following the machining process is known as surface…

Q: With reference to the drawing callout in Figure 4 below, which part(s) would 'pass' or 'fail'…

A:

Q: What is called the fit? 1) the difference between the maximum and minimum limits of size, 2) the…

A: Handwritten.jpg

Q: An assembly drawing with numbering of all parts and the dimensions needed only for assembling,…

A: AS per the Question Demand the Drawing of the Power Screw Device. Power Screw Device is the…

Q: 2) Explain the principle of working and operation of Ultrasonic Inspection with neat diagram.

A: To find Working of ultrasonic testing

Q: There is a difference in how "Amplification" is achieved on Mechanical Dial Indicators and Lever…

A: Mechanical Dial Indicators and Lever Type Dial Test indicatorss

Q: (a) Explain TWO reasons why the angle dimensions are necessary in the product design? (b) List THREE…

A:

Q: Explain with neat sketch of “Etching” the surface finishing process.

A: Etching : It is the process of preparing a material before introducing it to a microscope, Etching…

Q: Lathe is an example of _________.   a.   Marking tool   b.   Electrical tool   c.…

A: A Lathe is a Machine tool which rotates the work piece about an axis to perform certain kind of…

Q: surface tension analysis of a balloon?

A: Option c) Is correct Answer

Q: List three rules to follow when using or storing semi-precision measuring tools.

A: Semi precision tools are used for the measurement of the various dimensions of the workpiece.

Q: The test conducted by a scan tool can also be tested by some

A: Dear student please rate me positive :) Stay safe stay happy ! Answer-  Scan tool : it should be…

Q: Briefly define the purpose, types and construction of the hardness measurement.

A: The principal purpose of the hardness measurement  is to determine the suitability of a material for…

Q: Describe the principle of calibration and explain clearly how it works.  Use your own words.

A: Principle: 1) It is generally done for measuring instruments.  2) It is an measuring(checking)…

Q: seconds. If the next inspection is to take place in 30 days, would it be safe to delay the…

A:

Q: Functional testing check sheet for Lithotripsy machine, self-illuminating microscope and Holmium…

A: In the typical optical microscope's lighting system, the condenser which is located beneath the…

Q: The process best in terms of close control of tolerance and surface finish IS Casting Joining All of…

A: 1) Machining 2) high melting point material 3) all of the above

Q: The |type maintenance requires periodical inspection and testing.

A:

Q: Bilateral tolerance is Total tolerance is in 1 direction only Total tolerance is in both the…

A: As per our guidelines we are supposed to answer first one .Kindly repost other question as a…

Q: (a). Mention any four items must be available in the maintenance manual. (b). Draw the diagram and…

A: a] Maintenance manualIt is provided necessary information to maintain the system effectively and…