Automotive Technology: A Systems Approach (MindTap Course List)
6th Edition
ISBN: 9781133612315
Author: Jack Erjavec, Rob Thompson
Publisher: Cengage Learning
expand_more
expand_more
format_list_bulleted
Videos
Textbook Question
Chapter 27, Problem 11RQ
True or False? On some engines, if the gap between the crankshaft sensor and its trigger wheel is outside specifications, the sensor should be replaced.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
1) What is the effect if it occurs error data reading on Throttle Position Sensors?
2) What are the effects of accelerating and slow ignition timing?
Describe the operating principles of a knock sensor used in an engine management system? (100 - 150 words)
Because modern engines heat up rapidly heated oxygen sensor (ho2s) are not required.
True
False
Chapter 27 Solutions
Automotive Technology: A Systems Approach (MindTap Course List)
Ch. 27 - Name the three types of stress testing used to...Ch. 27 - Prob. 2RQCh. 27 - Name the three types of trace pattern display...Ch. 27 - Prob. 4RQCh. 27 - List at least two methods of checking the...Ch. 27 - What happens if one of the ground electrodes of a...Ch. 27 - True or False? The first test when checking a...Ch. 27 - Richer air-fuel mixtures. a. decrease the...Ch. 27 - Prob. 9RQCh. 27 - What does a slope in the spark line represent?
Ch. 27 - True or False? On some engines, if the gap between...Ch. 27 - What is the typical procedure for checking the...Ch. 27 - While checking a pickup coil with an ohmmeter, a...Ch. 27 - A CKP sensor can be checked with all of the...Ch. 27 - Which of the following will cause one or more, but...Ch. 27 - Prob. 1ASRQCh. 27 - Prob. 2ASRQCh. 27 - Prob. 3ASRQCh. 27 - Technician A says that EMI can affect sensor...Ch. 27 - While discussing waste spark EI systems:...Ch. 27 - While discussing how to test a Hall-effect...Ch. 27 - While discussing the possible causes for a...Ch. 27 - Prob. 8ASRQCh. 27 - While discussing EI service and diagnosis:...Ch. 27 - While discussing engine misfire diagnosis:...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- A defective LAT sensor or circuit may cause the fol lowing problems, except. hard engine starting rich or lean air-fuel ratio improper converter clutch lockup reduced fuel economyarrow_forwardWhich of the following is the most likely cause of a lean condition during acceleration and cruising speeds? a. A defective oxygen sensor b. A defective PCM c. A defective ECT sensor d. A defective MAF sensorarrow_forwardTrue or False? Some crankshaft and camshaft timing sensors have a specified gap that must be set during installation.arrow_forward
- Which of the following is the least likely cause of a no-start condition? Faulty CKP sensor Faulty KS Fuel or ignition system faults Faulty PCM wiringarrow_forwardWhich sensor is used for misfire monitoring on OBD II systems? Oxygen sensor Camshaft position sensor Crankshaft position sensor DPFE sensorarrow_forwardTrue or False? The neutral safety switch and reverse lamp switch are typically part of a digital transmission range sensor.arrow_forward
- While discussing how to test a Hall-effect crankshaft position sensor: Technician A says that a logic probe can be used. Technician B says that a DMM can be used. Who is correct? a. Technician A b. Technician B c. Both A and B d. Neither A nor Barrow_forwardWhich of the following is a likely cause of a lean condition during acceleration and cruising speeds? a. A defective oxygen sensor b. A defective PCM c. A defective ECT sensor d. A defective MAF sensorarrow_forwardWhen testing an engine temperature sensor: Technician A uses an ohmmeter to test the thermistor. Technician B says that the thermistor reacts to pressure and applies air pressure to the backside of the sensor. Who is correct? Technician A Technician B Both A and B Neither A nor Barrow_forward
- When testing a frequency varying MAF: Technician A says that the frequency should increase with an increase in engine speed. Technician B says that when observed on a lab scope, the signal from the sensor should be a square wave. Who is correct? Technician A Technician B Both A and B Neither A nor Barrow_forwardWhile diagnosing a cruise control system that does not turn on: Technician A checks the vehicle speed sensor and its input to the control module. Technician B checks the operation of the brake lights. Who is correct? Technician A Technician B Both A and B Neither A nor Barrow_forwardA transmission has delayed upshifts under all operating conditions: Technician A says that low mainline pressure can cause this. Technician B says that a faulty TFT sensor can cause this. Who is correct? a. Technician A only b. Technician B only c. Both A and B d. Neither A nor Barrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Automotive Technology: A Systems Approach (MindTa...Mechanical EngineeringISBN:9781133612315Author:Jack Erjavec, Rob ThompsonPublisher:Cengage Learning
Automotive TechnologyMechanical EngineeringISBN:9781337794213Author:ERJAVEC, Jack.Publisher:Cengage,
Automotive Technology: A Systems Approach (MindTa...
Mechanical Engineering
ISBN:9781133612315
Author:Jack Erjavec, Rob Thompson
Publisher:Cengage Learning
Automotive Technology
Mechanical Engineering
ISBN:9781337794213
Author:ERJAVEC, Jack.
Publisher:Cengage,
Mod-01 Lec-16 Basics of Instrumentation; Author: nptelhrd;https://www.youtube.com/watch?v=qbKnW42ZM5c;License: Standard YouTube License, CC-BY