Turn on your desk lamp. Pick up the cord, with your thumb and index finger spanning the width of the cord. (a) Compute an order-of-magnitude estimate for the current in your hand. Assume the conductor inside the lamp cord next to your thumb is at potential ~ 102 V at a typical instant and the conductor next to your index finger is at ground potential (0 V). The resistance of your hand depends strongly on the thickness and the moisture content of the outer layers of your skin. Assume the resistance of your hand between fingertip and thumb tip is ~ 104 Ω. You may model the cord as having rubber insulation. State the other quantities you measure or estimate and their values. Explain your reasoning. (b) Suppose your body is isolated from any other charges or currents. In order-of-magnitude terms, estimate the potential difference between your thumb where it contacts the cord and your finger where it touches the cord.
Want to see the full answer?
Check out a sample textbook solutionChapter 28 Solutions
Physics for Scientists and Engineers, Technology Update (No access codes included)
- The student engineer of a campus radio station wishes to verify the effectiveness of the lightning rod on the antenna mast (Fig. P21.71). The unknown resistance Rx is between points C and E. Point E is a true ground, but it is inaccessible for direct measurement because this stratum is several meters below the Earths surface. Two identical rods are driven into the ground at A and B, introducing an unknown resistance Ry. The procedure is as follows. Measure resistance R1 between points A and B, then connect A and B with a heavy conducting wire and measure resistance R2 between points A and C. (a) Derive an equation for Rx in terms of the observable resistances, R1 and R2. (b) A satisfactory ground resistance would be Rx 2.00 . Is the grounding of the station adequate if measurements give R1 = 13.0 and R2 = 6.00 ? Explain. Figure P21.71arrow_forwardA straight, cylindrical wire lying along the x axis has a length of 0.500 m and a diameter of 0.200 mm. It is made of a material described by Ohm’s law with a resistivity of ρ = 4.00 x 10-8 Ω ⋅ m. Assume a potential of 4.00 V is maintained at the left end of the wire at x = 0. Also assume V = 0 at x = 0.500 m. Find (a) the magnitude and direction of the electric field in the wire, (b) the resistance of the wire, (c) the magnitude and direction of the electric current in the wire, and (d) the current density in the wire. (e) Show that E = ρJ.arrow_forwardA straight, cylindrical wire lying along the x axis has a length of 0.5 m and a diameter of0.2 mm. It is made of a material described by Ohm’s law with a resistivity of ρ 4 × 10-8Ωm. Assume a potential of 4 V is maintained at the left end of the wire at x = 0. Alsoassume V = 0 at x = 0.5 m. Find (a) the magnitude and direction of the electric field in thewire, (b) the resistance of the wire, (c) the magnitude and direction of the electric currentin the wire, and (d) the current density in the wire. (e) Show that E = ρ J. (E = −dVdx)arrow_forward
- Consider a copper wire with a diameter of 2.75 mm. A. What is the drift speed of the electrons in the copper wire when a current of 13.0 A flows through it? Assume that each copper atom contributes one free electron to the metal. The density of copper is 8.92 g/cm3. B. How does this drift speed compare to the random rms speed of an electron at 20.0°C? To make this comparison, determine the random rms speed of an electron at 20.0°C using the ideal gas model and find the ratio of the two speeds.arrow_forwardA straight, cylindrical wire lying along the x axis has a length of 0.515 m and a diameter of 0.195 mm. It is made of a material described by Ohm's law with a resistivity of ? = 4.00 ✕ 10−8 Ω · m. Assume a potential of 4.00 V is maintained at the left end of the wire at x = 0. Also assume V = 0 at x = 0.515 m. (a) Find the magnitude (in V/m) and direction of the electric field in the wire. (b) Find the resistance of the wire (in Ω). (c) Find the magnitude (in A) and direction of the electric current in the wire. (d) Find the current density in the wire (in MA/m2). See image for the full question.arrow_forwardA cylindrical resistor of radius 5.0 mm and length 2.0 cm is made of material that has a resistivity of 3.5 * 10-5 ohm m.What are (a) the magnitude of the current density and (b) the potential difference when the energy dissipation rate in the resistor is 1.0W?arrow_forward
- What resistance, R, should be placed in series with the galvanometer, G, if it is to show a full deflection when the potential across the resistor is 6 V. The maximum current through the galvanometer is 250 mA and its internal resistance is 3 Ω. (a) 24 Ω (b) 23 Ω (c) 3 Ω (d) 5.25 Ω (e) 21arrow_forwardConsider two coaxial conducting spheres of radii a and b = 2a. Filled with a conductive material with resistivity p = p0 (1 + r / a) between the radii (region a≤r≤b). Calculate the resistance between the spheres.arrow_forwardIn the figure the resistances are R1 = 1.0 Ω and R2 = 2.0 Ω, and the ideal batteries have emfs ε1 = 2.9 V, and ε2 = ε3 = 3.7 V. What are the (a) size and direction (up or down) of the current in battery 1, the (c) size and direction of the current in battery 2, and the (e) size and direction of the current in battery 3?arrow_forward
- A capacitor with a capacitance of 3.5 μF is initially uncharged. It is connected in series with a switch of negligible resistance, a resistor with a resistance of 19 kΩ, and a battery that has a potential difference of 170 V. What is the charge Q, in microcoulombs, on the capacitor when the current in the resistor equals one half its maximum value.arrow_forwardIn these two examples, what exactly happens if the current goes from left to right? For the first example, when t = 0, where does the charge go? I know that after a long time, the capacitor will fill up and all the current goes through the resistor, but is it the same for t = 0? For the second example, I know that at t=0, all the current goes through the wire, but after a while all the current will go through the resistor?arrow_forwardYou decide to use a toaster to toast a slice of bread using the wall outlet of your home. Knowing that the voltage supply of your home is alternating given by the function V = 120 sin (2 πft), where f = 120 Hz and t is time in seconds: a) If the toaster oven uses nichrome wire that measures a total length of 0. 25 m with a thickness of 0.5 mm (diameter of wire), what is the resistance of the wire when heats up to 100.0 C from room temperature of 20. 0 °C? b) Knowing the resistance value of the wire from part a) and using Ohms Law, write the alternating current equation. c) What is the rms value for current and voltage for our toaster oven circuit? d) How much average electrical energy J does the toaster oven use if you toast your bread for 1 minute?arrow_forward
- Principles of Physics: A Calculus-Based TextPhysicsISBN:9781133104261Author:Raymond A. Serway, John W. JewettPublisher:Cengage LearningPhysics for Scientists and Engineers: Foundations...PhysicsISBN:9781133939146Author:Katz, Debora M.Publisher:Cengage Learning