Solid Waste Engineering
Solid Waste Engineering
3rd Edition
ISBN: 9781305635203
Author: Worrell, William A.
Publisher: Cengage Learning,
bartleby

Concept explainers

Question
Book Icon
Chapter 3, Problem 3.1P
To determine

The time required to complete the filling and emptying cycle for a refuse collection vehicle.

Expert Solution & Answer
Check Mark

Answer to Problem 3.1P

The time required to complete the filling and emptying cycle for a refuse collection vehicle is 194.28min .

Explanation of Solution

Given:

The two container of 80gallons each has 75% full.

The refuse is picked up twice per week.

The truck has a compaction ratio of 1:2 .

The pickup time is 1.58min per service.

The time spend by truck on disposal is 20min .

The time spend to reach the disposal site is 35min .

Calculation:

Assume the volume of the truck as 20yd3 .

Calculate the volume of refuse produced by each resident in yd3 .

  Vres=2×80gallons×( 0.00495 yd 3 1gallon)×0.75=0.594yd3

Here, the volume of refuses produces by each resident is Vres .

Write the expression to calculate the compacted volume by the truck’s compacting ratio.

  Vcom=12×Vres  ..... (I)

Here, the compacted volume is Vcom and the volume of refuse produced by each resident is Vres .

Substitute 0.594yd3 for Vres in Equation (I).

  Vcom=12×0.594yd3=0.297yd3

Write the expression to calculate the number of loads done by the truck.

  L=VtruckVcom  ..... (II)

Here, the number of loads done by the truck is L , the volume of the truck is Vtruck and the compacted volume is Vcom .

Substitute 20yd3 for Vtruck and 0.297yd3 for Vcom in Equation (II).

  L=20 yd30.297 yd3=67.3468

Write the expression to calculate the total time of cycle.

  TC=2×Td+(Ts×L)+Tdis  ..... (III)

Here, the total time of cycle is TC , the time spend to reach the disposal site is Td , the number of loads done by the truck is L , the service time is Ts and the time spend by truck on disposal is Tdis .

Substitute 35min for Td , 1.58min for Ts , 68 for L and 20min for Tdis in Equation (III).

  TC=2×35min+(1.58min×66)+20min=70min+104.28min+20min=194.28min

Conclusion:

Thus, the time required to complete the filling and emptying cycle for a refuse collection vehicle is 194.28min .

Want to see more full solutions like this?

Subscribe now to access step-by-step solutions to millions of textbook problems written by subject matter experts!
Students have asked these similar questions
Calculate the number of stops in each trip of 1.50 h of refuse collection for the following data v= velocity = 15 km/h – 4.17 m/s d= distance= 750 m n = number of containers to empty per stop=1 tc= time to empty one bin/container= 650 s
Street is 1000 foot long and homes are 50 feet apart on both sides of the road. Two person crew are employed to collect the recyclables in green roll out containers. It takes 30 seconds to empty the contents to each green container into the truck and set out amount of 12 kgs . Estimate the total time to collect recyclables.
Assume it cost an average of $0.03/ton.min to haul waste from collection to transfer station and then from the transfer station to landfill using a transfer vehicle and the operation cost of the transfer station is $2/ton. The cost of hauling waste directly from the collection point to landfill is $0.1/ton.min. The speed limit of any type of vehicle carrying waste between the collection point, the transfer station, and the landfill is 40 miles/hr. At/above what distance (miles) is using a transfer station more economical? Round your answer to the nearest whole number. Show your work.
Knowledge Booster
Background pattern image
Civil Engineering
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.
Similar questions
Recommended textbooks for you
Text book image
Solid Waste Engineering
Civil Engineering
ISBN:9781305635203
Author:Worrell, William A.
Publisher:Cengage Learning,