Steel Design (Activate Learning with these NEW titles from Engineering!)
6th Edition
ISBN: 9781337094740
Author: Segui, William T.
Publisher: Cengage Learning
expand_more
expand_more
format_list_bulleted
Question
Chapter 3, Problem 3.3.8P
To determine
(a)
If the member can resist service loads using load and resistance factor design (LFRD) method.
To determine
(b)
If the member can resists service loads using Strength Design (ASD).
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solutionStudents have asked these similar questions
A 15" x 3/8" bar of A572 Gr. 50 steel is used as a tension member. It is connected to a gusset plate with 7/8-in diameter bolts as shown in the figure. Use s = 2.0 and g = 3.0.
a) Determine the allowable tensile strength of the section based on tensile rupture of the net area.b) Determine the allowable tensile strength of the section based on yielding of the gross area.
A 15" x 3/8" bar of A572 Gr. 50 steel is used as a tension member. It is connected to a gusset plate with 7/8-in diameter bolts as shown in the figure. Use s = 2.0 and g = 3.0.
Determine the allowable tensile strength of the section based on tensile rupture of the net area.
A 15" x 3/8" bar of A572 Gr. 50 steel is used as a tension member. It is connected to a gusset plate with 7/8-in diameter bolts as shown in the figure. Use s = 2.0 and g = 3.0.
Determine the design tensile strength of the section based on tensile rupture of the net area.
Determine the allowable tensile strength of the section based on yielding of the gross area.
Chapter 3 Solutions
Steel Design (Activate Learning with these NEW titles from Engineering!)
Ch. 3 - Prob. 3.2.1PCh. 3 - Prob. 3.2.2PCh. 3 - Prob. 3.2.3PCh. 3 - Prob. 3.2.4PCh. 3 - Prob. 3.2.5PCh. 3 - Prob. 3.2.6PCh. 3 - Prob. 3.3.1PCh. 3 - Prob. 3.3.2PCh. 3 - Prob. 3.3.3PCh. 3 - Prob. 3.3.4P
Ch. 3 - Prob. 3.3.5PCh. 3 - Prob. 3.3.6PCh. 3 - Prob. 3.3.7PCh. 3 - Prob. 3.3.8PCh. 3 - Prob. 3.4.1PCh. 3 - Prob. 3.4.2PCh. 3 - Prob. 3.4.3PCh. 3 - Prob. 3.4.4PCh. 3 - Prob. 3.4.5PCh. 3 - Prob. 3.4.6PCh. 3 - Prob. 3.5.1PCh. 3 - Prob. 3.5.2PCh. 3 - Prob. 3.5.3PCh. 3 - Prob. 3.5.4PCh. 3 - Prob. 3.6.1PCh. 3 - Prob. 3.6.2PCh. 3 - Prob. 3.6.3PCh. 3 - Select an American Standard Channel shape for the...Ch. 3 - Prob. 3.6.5PCh. 3 - Use load and resistance factor design and select a...Ch. 3 - Select a threaded rod to resist a service dead...Ch. 3 - Prob. 3.7.2PCh. 3 - Prob. 3.7.3PCh. 3 - Prob. 3.7.4PCh. 3 - Prob. 3.7.5PCh. 3 - Prob. 3.7.6PCh. 3 - Prob. 3.8.1PCh. 3 - Prob. 3.8.2PCh. 3 - Prob. 3.8.3PCh. 3 - Prob. 3.8.4PCh. 3 - Prob. 3.8.5P
Knowledge Booster
Similar questions
- TENSION MEMBERS: THE SINGLE 200 X 10 mm STEEL PLATE IS CONNECTED TO A 12 mm THICK STEEL PLATE BY FOUR 16 mm DIAMETER RIVETS AS SHOWN IN THE FIGURE. THE RIVETS USED ARE A502 GRADE 2, HOT DRIVEN RIVETS. THE STEEL IS ASTM A36 WITH Fy = 248 MPa AND Fu = 400 MPa. DETERMINE THE VALUE OF P. a. P BASED ON TENSION OF GROSS AREA b. P BASED ON TENSION OF NET AREA c. P BASED ON BEARING OF PROJECTED AREA d. P BASED ON SHEAR RUPTURE (BLOCK SHEAR)arrow_forwardDetermine the design tensile strength of plate (200x8 mm) connected to 10-mm thick gusset using 20 mm bolts as shown in the figure, if the yield and the ultimate stress of the steel used are 250 MPa and 410 MPa, respectively. Add 1mm around the bolt for the hole. Use LRFD method. Plate 8-mm thick 2 3 40+ 30 301 T 200 mm Gusset 10-mm thick 3af 30 2_3 *40 40+ 50,54 +40arrow_forwardA 15" x 3/8" bar of A572 Gr. 50 steel is used as a tension member. It is connected to a gusset plate with 7/8-in diameter bolts as shown in the figure. Use s = 2.0 and g = 3.0. Determine the critical net area of the connection shown. Determine the design tensile strength of the section based on yielding of the gross area.arrow_forward
- A 15" x 3/8" bar of A572 Gr. 50 steel is used as a tension member. It is connected to a gusset plate with 7/8-in diameter bolts as shown in the figure. Use s = 2.0 and g = 3.0.a) Determine the design tensile strength of the section based on yielding of the gross area.b) Determine the critical net area of the connection shown.arrow_forwardTwo plates each with thickness t= 16 mm are bolted together with 6-22mm bolts forming a lap connection. Bolt spacing are as follows: S1=40 mm, S2=80 mm, S3=100 mm. Bolt hole diameter= 25mm. (a)Compute the bearing stress of the bolt and hole if the P = 200KN. (b)If allowable bearing stress is 480MPa, compute the value of P.arrow_forwardA L 3 x 2 x ¼ is connected to a gusset plate via six bolts. The nominal diameter of the bolt is 0.25 inches, the pitch spacing is 1.75 inches, the gage spacing is 2 inches, and the thickness of the connection is (¼) inch. The yield stress is 50 Ksi and the ultimate stress is 60 Ksi. Consider section line (a-a') for the analysis. . a. What is the effective net area (Ae) of the angle section in inches2 [a-a']?(The shear lag factor is "0.80") b. What is the design tensile yielding strength in Kips for the steel member? c. What is the design tensile rupture strength in Kips for the steel member? d. What is the minimum Factor of Safety if a tensile load of 23 Kips is applied to the angle section? please make sure the answer is correct 100% I only need the final answersarrow_forward
- An unsymmetrical flexural member consists of a ½ × 12 top flange, a ½ × 7 bottom flange, and a ⅜ × 16 web. a. Determine the distance y from the top of the shape to the horizontal plastic neutral axis. b. If A572 Grade 50 steel is used, what is the plastic moment M, for the horizontal plastic neutral axis? c. Compute the plastic section modulus Z with respect to the minor principal axis. Pls help!arrow_forwardDetermine: Ix & ly = Moment of inertia about axis XX and YY Rx & Ry = Radius of gyration about axis XX and YY Sx & Sy = Elastic modulus about axis XX and YY steel specs are here http://www.toolsforengineer.com/steel-sections-properties-tables/ FOR WIDE FLANGE = W250X22FOR ANGLE BAR = L32X32X6.4arrow_forwardSubject: Steel Design A W300 x 67 has two lines of 20 mm dia. Bolts in each flange (3 bolts in each line which has spacing as shown. A36 steel is used with Fy = 250 MPa, Fu = 400 MPa. Properties of W300 x 67 A = 8250 mm2 bf = 201.05 mm tf = 14.40 mm d = 300mm tw = 8.4 mm a) Compute the effective net area of the section b) Compute the allowable tensile strength of the section. Note: Dimensions in the drawing are in mmarrow_forward
- The angle L 8 x 8 x ½ in tension shown in the figure below must resist aservice dead load of 35 kips, live load of 50 kips, and a roof live load of 2kips. The steel used is A50 (Fy = 50 ksi, Fu = 65 ksi) and its welding length is 4”.Determine if the member has sufficient fracture and yield strength.arrow_forwardDetermine the effective net area of the L7 × 4 × 1/2 shown in the figure. Assume the holes are for 1-in Ø bolts. Use the U values given in Table 3.2. (Ans. 3.97 in^2)arrow_forwardNote: Hi, pls need help. Any solutions are highly appreciated. I will rate this right away. Thank you in advance! What is the required diameter of sag rods in mm? Considering sag rods and tie rods at midspan (rounded value) A 20m Fink Truss are spaced at 'S' meters o.c. the purlins are made up of C10X20 sections and are spaced 1.1967m on centers. The truss has a height of 4m. Roof LL is 'RLL' N/m2 of roof surface and roof covering is assumed to be 'RDL' N/m2 of roof surface. Determine whether the purlins are adequate to carry such loadings. Given: Fy=248 MPa w=29.76 Kg/m A=3787.09 mm^2 Ix=32.84×10^6 mm^4 Iy=1.17×10^6 mm4 Zx=317.91×10^3 mm3 Sx=258.92×10^3 mm3 Zy=44.25×10^3 mm3 Sy=21.47×10^3 mm3 S= 6 m RLL=900 N/m^2 RDL= 900 N/m^2arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Steel Design (Activate Learning with these NEW ti...Civil EngineeringISBN:9781337094740Author:Segui, William T.Publisher:Cengage Learning
Steel Design (Activate Learning with these NEW ti...
Civil Engineering
ISBN:9781337094740
Author:Segui, William T.
Publisher:Cengage Learning