Find the resultant of the two forces and the couple shown, given that P1 = 20 lb, P2 = 30 lb, and C = 100 lb · in.

Q: Determine the heat input given to a Carnot engine cycle operates with air shown in figure T = 500 K ...

A:

Q: two suggestions in reducing the head loss in the pump and piping system

A: -Make the surface of the pipe is smooth so that no friction is present in the piping system so this ...

Q: For a bronze alloy, the stress at which plastic deformation begins is 267 MPa and the modulus of ela...

A:

Q: In psychrometric chart, how to estimate the maximum values of sensible and latent heat gains in a ro...

A: Sensible heat: It can be defined as a process in which we are going to increase the Temperature for ...

Q: What are the Miller indices for the plane shown below?

A: Miller indices :- Miller indices are the group of 3 numbers that indicates the orientation of a plan...

Q: Convert 30 kelvin to degrees celsius.

A: Temperature is the degree of Hotness and It is represented in the degree Its Units are Kelvin, Celsi...

Q: I just seen a specific heat question where the notation was given in kJ/kg¹ K¹ (exponent is negative...

A: Specific heat is defined as the amount of heat required to raise the temperature of a unit mass (1kg...

Q: b)Calculate Degree of freedom for the following figure. Activate Windows Go to Settings to activate ...

A:

Q: A vapor compression refrigeration system with R-134a as refrigerant is used to cool down 0.1 m3/s ai...

A: Refrigerant = R-134a Volume flow rate of Air, V˙a=0.1 m3/s Inlet condition of air, Ta,i=25oC and 20%...

Q: Ductile and brittle fracture (what are they, how do they look under microscope)

A: Ductile fracture is a type of fracture characterised by a broad plastic deformation or "necking." Th...

Q: (a) Use the following data to calculate the area of solar domestic hot water collector that would be...

A: Given Temperature of water required by the family is Th=60°C. Temperature of supply water is Tl=15°...

Q: Diffsuion process is faster for____   A) Covalently bonded materials   B) High den...

A: Solution:   Note: Dear Student! As per our guidelines, we are only allowed to answer a single questi...

Q: • Sliting is the operation of: Removal of metal to the desired shape from the edge of a plate. OACut...

A: Slitting is a sheet metal cutting operation carried on the sheets of the metal by using circular kni...

Q: The man exerts a force P of magnitude 150N on the handle of the wheelbarrow. Knowing that the result...

A:

Q: Determine the moment of inertia of the inverted T section about the base of the section. Draw the di...

A: Given data: The width of the web is W = 120 mm. The height of the section is H = 220 mm. The thickn...

Q: A plate made of steel 20C8 (S, = 440 N/mm²) in hot rolled and normalised condition is shown in Fig. ...

A: Given Sut= 440 N/mm2. P=±30KN q=0.8 FOS=2 Kb=0.85 Reliability =90%

Q: 12- A simple pendulum was formed by hanging the mass m from point A with a 6 (m) long rope. pendulum...

A:

Q: Calculate the amount of energy consumed by a 75kg person jumping up 70 cm for 10 minutes at a rate o...

A:

Q: A cylindrical specimen of tungsten having a diameter of 15 mm (A=177 mm^2) and length of 210 mm is d...

A: Specimen diameter, d=15mm=0.015m Cross sectional area of specimen, A=177mm2=0.00017 m2 Length of spe...

Q: mechanics of materials question is image q2) ?

A:  

Q: The supporting wheel on a scaffold is held in place on the leg using a 4- mm -diameter pin as shown....

A: given pin diameter d=4mmnormal force P=2.3kN

Q: Determine the normal force P that must be exerted on the rack to begin pushing the 100kg pipe shown ...

A: Write the given data with suitable variables. m=100 kgμsA=0.15μsB=0.4

Q: Cite two reasons why interstitial diffusion is normally more rapid than vacancydiffusion.

A: Interstitial diffusion is a diffusion method in which small solutes particles occupy the interstitia...

Q: Determine the centroid of an unequal l-section about the base of the section. Specifications are as ...

A: Solution: Since axises are not specified, we can assume the axis as shown below. The x-coordinate of...

Q: Steam is supplied to a fully loaded 100-hp turbine at 200 psia with u1= 1163.3 Btu/lb, v1= 2.65 cu.f...

A:

Q: Consider a cylindrical titanium wire with crossectional area of 7 mm^2 and 2.5 x 104 mm long. Calcul...

A: Write the expression for elongation in the rod.  

Q: There exists reduction of 1 pound of steam per minute undergoing an isothermal process from 27.5 bar...

A: Given- mass flow rate (m) = 1 pound/minute = 0.01667 pound/sec  (m) = 0.00756 kg/s Change in kinetic...

Q: Determine from the beam and the loads shown: Reactions on supports Shear force diagram Bending momen...

A: Hello. Since your question has multiple sub-parts, we will solve first three sub-parts for you. If y...

Q: An oil is acting as a lubricant for a pair of cylindrical surfaces. The angular velocity of the oute...

A:

Q: (c) Draw the shear and moment diagrams for the loaded beam.

A: Given Data: The loads acting on the beam are P=1000 N and M=2100 N·m. The free-body diagram of the...

Q: Design a heat equation model to determine the solution. The physical data needed to model for copper...

A:

Q: An air receiver carries a pressure of 3500 kPa absolute @ a temperature of 25 C. A fire occurs near ...

A:

Q: l'he uniform pole of length I and against the supporting surfaces she cient of static friction is u,...

A: given:static friction μs=0.25length of the pole=lmass of the pole=m

Q: Also i need the path of contact

A: Gear transmission is used to transmit rotary motion into rotary motion by using toothed wheels. In a...

Q: In the continuous regime, there is a constant heat generation of q = 3x107 W/m³ in a one-dimensional...

A:

Q: Determine the displacement of point C. Use the method of virtual work. EI is constant. Solve Prob. 9...

A: If a rigid body or a system of bodies is present having equilibrium condition under various forces a...

Q: image

A: As per our Q&A guidelines we are supposed only one question at once kindly repost the other as s...