Fluid Mechanics: Fundamentals and Applications
Fluid Mechanics: Fundamentals and Applications
4th Edition
ISBN: 9781259696534
Author: Yunus A. Cengel Dr., John M. Cimbala
Publisher: McGraw-Hill Education
bartleby

Videos

Textbook Question
Book Icon
Chapter 3, Problem 49P

Repeat Prob. 3-48 by replacing the air with oil whose specific gravity is 0.72.

Expert Solution & Answer
Check Mark
To determine

The pressure difference between two pipelines.

Answer to Problem 49P

The pressure difference is 10.336kPa.The air column can be ignored since the density of air very low.

Explanation of Solution

Given information:

The density of seawater is 1035kg/m3.

The following figure represents freshwater and seawater flowing in parallel horizontal pipelines which are connected to each other by a double U-tube manometer.

  Fluid Mechanics: Fundamentals and Applications, Chapter 3, Problem 49P

Figure-(1)

Write the equation for the pressure difference of sea water and fresh water.

  ΔP=PHg+PoilPfwPsw   ...... (I)

Here, the pressure difference is ΔP, the pressure on mercury is PHg, the pressure on oil is Poil, pressure on freshwater is Pfw and pressure on seawater is Psw.

Write the expression for pressure on oil.

  Poil=ρoil×g×hoilPoil=(SG oil×ρw)×g×hoil   ...... (II)

Here, density of oil is ρoil, acceleration due to gravity is g, height of oil column is hoil, specific gravity of oil is SGoil, and density of water is ρw.

Write the expression for density of mercury.

  ρHg=SGHg×ρw   ...... (III)

Here, specific gravity of mercury is SGHg and density of water is ρw.

Write the expression for pressure on mercury.

  PHg=ρHg×g×hHg   ...... (IV)

Here, pressure on mercury is PHg, density of mercury is ρHg, acceleration due to gravity is g, and height of mercury column is hHg.

Write the expression for pressure on seawater.

  Psw=ρsw×g×hsw...... (V)

Here, pressure on seawater is Psw, density of seawater is ρsw, acceleration due to gravity is g, height of seawater column is hsw.

Write the expression for pressure on seawater.

  Pfw=ρfw×g×hfw...... (VI)

Here, pressure on freshwater is Pfw, density of freshwater is ρfw, acceleration due to gravity is g, height of freshwater column is hfw.

Calculation:

Substitute 0.72 for ρoil, 1000kg/m3 for ρw, 9.81m/s2 for g and 70cm for hoil in Equation (II).

  Poil=0.72×(9.81m/ s 2)×(70cm)=(0.72×1000kg/ m 3)×(9.81m/ s 2)×(70cm× 1m 100cm)=(720kg/ m 3)×(9.81m/ s 2)×(0.7m)=4944.2kg ms2

  poil=4944.2kg/ms2( 1Pa 1 kg/ ms 2 )=4944.2Pa( 1Pa 1000kPa)=4.944kPa

Substitute 13.6 for SGHg and 1000kg/m3 for ρw in Equation (III).

  ρHg=(13.6)(1000kg/ m 3)=13600kg/m3

Substitute 13600kg/m3 for ρHg, 9.81m/s2 for g and 10cm for hHg in Equation (IV).

  PHg=(13600kg/ m 3)(9.81m/ s 2)(10cm)=(13600kg/ m 3)(9.81m/ s 2)(10cm× 1m 100cm)=(13600kg/ m 3)(9.81m/ s 2)(0.1m)=13341.6kg/ms2

  PHg=13341.6kg/ms2( 1Pa 1 kg/ ms 2 )=13341.6Pa( 1Pa 1000kPa)=13.34kPa

Substitute 1035kg/m3 for ρsw

  9.81m/s2 for g and 30cm for hsw in Equation (V).

  Psw=(1035kg/ m 3)(9.81m/ s 2)(30cm)=(1035kg/ m 3)(9.81m/ s 2)(30cm× 1m 100cm)=(1035kg/ m 3)(9.81m/ s 2)(0.3m)=3045.0055kg/ms2

  Psw=3045.0055kg/ms2( 1Pa 1 kg/ ms 2 )=3045.0055Pa( 1Pa 1000kPa)=3.045kPa

Substitute 1000kg/m3 for ρfw, 9.81m/s2 for g and 50cm for hfw in Equation (VI).

  Pfw=(1000kg/ m 3)(9.81m/ s 2)(50cm)=(1000kg/ m 3)(9.81m/ s 2)(50cm× 1m 100cm)=(1000kg/ m 3)(9.81m/ s 2)(0.5m)=4905kg/ms2

  Pfw=4905kPa( 1Pa 1 kg/ ms 2 )=4905kPa( 1Pa 1000kPa)=4.9kPa

Substitute 13.34kPa for PHg, 4.944kPa for Poil, 4.905kPa for Pfw and 3.045kPa for Psw in Equation (I)/

  ΔP=13.34kPa+4.944kPa+4.905kPa+3.045kPa=10.336kPa

Conclusion:

The pressure difference is 10.336kPa.The air column can be ignored since the density of air very low.

Want to see more full solutions like this?

Subscribe now to access step-by-step solutions to millions of textbook problems written by subject matter experts!
Students have asked these similar questions
5. What is the pressure at the bottom of the 7.5 m tall storage tank of fluid at 25°C? Assume that the fluid is gasoline with atmospheric pressure 101 kPa on the top surface. Repeat the question for the liquid refrigerant R- 134a when the top surface pressure is 1 MPa. The densities of the liquids are: pgasoline = 750 kgm; PR-134a = 1206 kg/m2. %3D
the gauge pressure of the air in the tank is shown in Fig. p3-49 is measured to be 65 kPa. Determine the differential height H of the mercury column.
An experiment was conducted using a communicating vessel to knowthehydraulic pressure. The communicating vessel consists of two column, XandY. Column X has a diameter of 15 cm and column Y of 75 cm. Oil (s = 0.852) wasfilled to the communicating vessel. A load of 1275 N was given to the columnY. Determine the minimum force that should be given to column Xso that theload can be lifted and the density of oil !

Chapter 3 Solutions

Fluid Mechanics: Fundamentals and Applications

Ch. 3 - Show that 1kgf/cm2=14.223psi .Ch. 3 - The pressure in a water line is 1500 kPa. What is...Ch. 3 - Blood pressure is usually measured by rapping a...Ch. 3 - The maximum blood pressure in the upper arm of a...Ch. 3 - Consider a 1.73-m-tall man standing vertically in...Ch. 3 - A manometer is used to measure the air pressure in...Ch. 3 - The water in a tank is pressurized by air, and the...Ch. 3 - Determine the atmospheric pressure at a location...Ch. 3 - The gagepressure in a liquid at a depth of 2.5 m...Ch. 3 - The absolute pressure in water at a depth of 8 m...Ch. 3 - A 180-Ibm man has a total foot imprint area of 68...Ch. 3 - Consider a 55-kg woman who has a total foot...Ch. 3 - A vacuum gage connected to a tank reads 45 kPa at...Ch. 3 - The piston of a vertical piston-cylinder device...Ch. 3 - The vacuum pressure of a condenser is given to be...Ch. 3 - Water from a reservoir is raised in a vertical...Ch. 3 - The barometer of a mountain hiker reads 980 mbars...Ch. 3 - Determine the pressure exerted on a diver at 15 m...Ch. 3 - A gas is contained in a vertical, frictionless...Ch. 3 - The variation of pressure P in a gas with density ...Ch. 3 - Both a gage and a manometer are attached to a gas...Ch. 3 - The system shown in the figure is used to...Ch. 3 - The manometer shown in the figure is designed to...Ch. 3 - A manometer containing ( =850kg/m3 ) attached to a...Ch. 3 - A mercury ( =13,600kg/m3 ) is connected to an air...Ch. 3 - Repeat Prob. 3-37 for a differential mercury...Ch. 3 - Consider a U-tube whose arms are open to the...Ch. 3 - The hydraulic lift in a car repair shop has an...Ch. 3 - Consider a double-fluid manometer attached to an...Ch. 3 - The pressure in a natural gas pipeline is measured...Ch. 3 - Repeat Prob. 3-42E by replacing air by oil with a...Ch. 3 - The gage pressure of the air in the tank shown in...Ch. 3 - Repeat Prob. 3-44 for a gage pressure of 40 kPa.Ch. 3 - The 500-kg load on the hydraulic lift show in Fig....Ch. 3 - Pressure is often given in terms of a liquid...Ch. 3 - Freshwater and seamier flowing in parallel...Ch. 3 - Repeat Prob. 3-48 by replacing the air with oil...Ch. 3 - The pressure difference between an oil pipe and...Ch. 3 - Consider the system shown in Fig. P3-51. If a...Ch. 3 - There is water at a height of 1 m in the rube open...Ch. 3 - Prob. 53PCh. 3 - A simple experiment has long been used to...Ch. 3 - A multifluid container is connected to a U-tube....Ch. 3 - A hydraulic lift is to be used to lift a 2500 kg...Ch. 3 - On a day in which the local atmospheric pressure...Ch. 3 - A U-tube manometer is used to measure the pressure...Ch. 3 - Define the resultant hydrostatic force acting on a...Ch. 3 - You may have noticed that dams are much thicker at...Ch. 3 - Someone claims that she can determine the...Ch. 3 - A submersed horizontal flat plate is suspended in...Ch. 3 - Consider a submerged curved surface. Explain how...Ch. 3 - Consider a submersed curved surface. Explain how...Ch. 3 - Consider a circular surface subjected to...Ch. 3 - Consider a 200-ft-high, dam filled to capacity....Ch. 3 - A cylindrical tank is folly filled with water...Ch. 3 - Consider a 8-m-long, 8-m-wide, and 2-m-high...Ch. 3 - Consider a heavy car submerged in water in a lake...Ch. 3 - A room the lower level of a cruise ship has a...Ch. 3 - The water side of the wall of a 70-m-long dam is a...Ch. 3 - A water trough of semicircular cross section of...Ch. 3 - Determine the resultant force acting on the...Ch. 3 - A 6-m-high, 5-m-wide rectangular plate blocks the...Ch. 3 - The flow of water from a reservoir is controlled...Ch. 3 - Repeat Prob. 3-76E for a water height of 6 ft.Ch. 3 - For a gate width of 2 m into the paper (Fig....Ch. 3 - A long, solid cylinder of radius 2 ft hinged at...Ch. 3 - An open settling tank shown in the figure contains...Ch. 3 - From Prob. 3-80, knowing that the density of the...Ch. 3 - The two sides of a V-shaped water trough are...Ch. 3 - Repeat Prob. 3-82 for the case of a partially...Ch. 3 - The bowl shown in the figure (the white volume) is...Ch. 3 - A triangular-shaped gate is hinged at point A, as...Ch. 3 - Gate AB ( 0.60.9m ) is located at the bottom of a...Ch. 3 - Find the force applied by support BC to the gate...Ch. 3 - A concrete block is attached to the sate as shown....Ch. 3 - A 4-m-long quarter-circular gate of radius 3 m and...Ch. 3 - Repeat Prob. 3-90 for a radius of 2 m for the...Ch. 3 - What is buoyant force? What causes it? What is the...Ch. 3 - Prob. 93CPCh. 3 - Consider two 5-cm-diaineter spherical balls-one...Ch. 3 - Prob. 95CPCh. 3 - Consider two identical spherical bails submerged...Ch. 3 - Prob. 97PCh. 3 - The hull of a boat has a volume of 180 m3, and the...Ch. 3 - The density of a liquid is to be determined by an...Ch. 3 - Prob. 100PCh. 3 - It is estimated that 90 percent of an iceberg’s...Ch. 3 - One of the common procedures in fitness programs...Ch. 3 - The weight of a body is usually measured by...Ch. 3 - Under what conditions can a moving body of fluid...Ch. 3 - Consider a vertical cylindrical container...Ch. 3 - Consider two identical glasses of water, one...Ch. 3 - Consider a glass of water. Compare the water...Ch. 3 - A water tank is being towed by a truck on a level...Ch. 3 - Consider two water tanks filled with water. The...Ch. 3 - Prob. 111PCh. 3 - The bottom quarter of a vertical cylindrical tank...Ch. 3 - A 3-m-diameter, 7-m-long cylindrical tank is...Ch. 3 - A 30-cm-diameter, 90-cm-high vertical cylindrical...Ch. 3 - A fish tank that contains 60-cm-high water is...Ch. 3 - A15-ft-long, 6-ft-high rectangular tank open to...Ch. 3 - Consider a tank of rectangular cross-section...Ch. 3 - A 3-ft-diameter vertical cylindrical lank open to...Ch. 3 - Milk with a density of 1020 kg/m3 is transported...Ch. 3 - Prob. 120PCh. 3 - The distance between the centers of the two arms...Ch. 3 - A 1.2-m-diameter, 3-m-high scaled vertical...Ch. 3 - A 4-m-diameter vertical cylindrical milk tank...Ch. 3 - An 8-ft-long tank open to the atmosphere initially...Ch. 3 - Prob. 126PCh. 3 - Prob. 127PCh. 3 - Prob. 128PCh. 3 - Two vertical and connected cylindrical tanks of...Ch. 3 - The U-tube shown the figure subjected to an...Ch. 3 - Prob. 131EPCh. 3 - An air-conditioning system requires a 34-m-long...Ch. 3 - Determine the pressure exerted on the surface of a...Ch. 3 - A vertical, frictionless piston-cylinder device...Ch. 3 - If the rate of rotational speed of the 3-tube...Ch. 3 - The average atmospheric pressure on earth is...Ch. 3 - Prob. 137PCh. 3 - Prob. 139PCh. 3 - The basic barometer can be used as an...Ch. 3 - The lower half of a 12-m-high cylindrical...Ch. 3 - Prob. 142PCh. 3 - A pressure cooker cooks a lot faster than an...Ch. 3 - Prob. 144PCh. 3 - An oil pipeline and a 1.3-m3 rigid air tank are...Ch. 3 - A 20-cm-diameter vertical cylindrical vessel is...Ch. 3 - Prob. 148PCh. 3 - A gasoline line is connected to a pressure gage...Ch. 3 - Prob. 151PCh. 3 - Prob. 152EPCh. 3 - Consider a U-tube filled with mercury as shown in...Ch. 3 - The variation of pressure with density in a thick...Ch. 3 - A 3-m-high. 5-m-wide rectangular gale is hinged al...Ch. 3 - Prob. 156PCh. 3 - A semicircular 40-ft-diameter tunnel is to be...Ch. 3 - A 30-ton. 4-m-diameter hemispherical dome on a...Ch. 3 - The water in a 25-m-deep reservoir is kept inside...Ch. 3 - A 5-m-long, 4-m-high tank contains 2.5-m-deep...Ch. 3 - The density of a floating body can be determined...Ch. 3 - A raft is made using a number of logs with 25 cm...Ch. 3 - A prismatic timber is at equilibrium in a liquid,...Ch. 3 - The cylindrical lank containing water accelerates...Ch. 3 - A 30-cm-diameter. 100-cm-hish vertical cylindrical...Ch. 3 - The 280-ke, 6-m-wide rectangular gate shown in Fig...Ch. 3 - Prob. 168PCh. 3 - Determine the vertical force applied by water on...Ch. 3 - Prob. 170PCh. 3 - In order to keep the cone-shaped plus closed as...Ch. 3 - The gage pressure in a pipe is measured by a...Ch. 3 - Prob. 173PCh. 3 - Prob. 174PCh. 3 - The atmospheric pressure in a location is measured...Ch. 3 - Prob. 176PCh. 3 - Prob. 177PCh. 3 - Consider the vertical rectangular wall of a water...Ch. 3 - Prob. 179PCh. 3 - Prob. 180PCh. 3 - Prob. 181PCh. 3 - Prob. 182PCh. 3 - Prob. 183PCh. 3 - Prob. 184PCh. 3 - Consider a 6-m-diameter spherical sate holding a...Ch. 3 - Prob. 186PCh. 3 - Prob. 187PCh. 3 - Prob. 188PCh. 3 - Prob. 189PCh. 3 - Prob. 190PCh. 3 - Prob. 191PCh. 3 - Prob. 192PCh. 3 - Shoes are to be designed to enable people of up to...Ch. 3 - The volume of a rock is to be determined without...Ch. 3 - Compare fee vortex with forced vortex according to...Ch. 3 - The density of stainless steel is about 8000 kg/m3...
Knowledge Booster
Background pattern image
Mechanical Engineering
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.
Similar questions
SEE MORE QUESTIONS
Recommended textbooks for you
Text book image
International Edition---engineering Mechanics: St...
Mechanical Engineering
ISBN:9781305501607
Author:Andrew Pytel And Jaan Kiusalaas
Publisher:CENGAGE L
Physics 33 - Fluid Statics (1 of 10) Pressure in a Fluid; Author: Michel van Biezen;https://www.youtube.com/watch?v=mzjlAla3H1Q;License: Standard YouTube License, CC-BY