Welding: Principles and Applications (MindTap Course List)
Welding: Principles and Applications (MindTap Course List)
8th Edition
ISBN: 9781305494695
Author: Larry Jeffus
Publisher: Cengage Learning
bartleby

Concept explainers

bartleby

Videos

Textbook Question
Chapter 31, Problem 18R

Why must the pressure be bled off hoses when work is complete?

Blurred answer
Students have asked these similar questions
How long would it take to purge a 15ft section of 6in diameter pipe using a flow rate of 35cfh?
Why is the remaining fluid at the delivery tip of a Mohr pipet is not blown out?
How long would it take to purge a 10mm section of a 20 cm dia.eter pipe using a flow rate 17L/min?

Chapter 31 Solutions

Welding: Principles and Applications (MindTap Course List)

Ch. 31 - Why are combination welding and cutting torches...Ch. 31 - What is the advantage of using an injector-type...Ch. 31 - What should be done to the valve packing if the...Ch. 31 - What may happen to a tip seat if it is incorrectly...Ch. 31 - What can happen to a tip if it is excessively...Ch. 31 - What is the difference between a reverse flow...Ch. 31 - What are Siamese hoses?Ch. 31 - Why must the pressure be bled off hoses when work...Ch. 31 - What is the difference between a backfire and a...Ch. 31 - Why is a neutral flame the most commonly used...Ch. 31 - What properties should a good leak-detecting...Ch. 31 - Why must the oxygen cylinder valve be opened all...Ch. 31 - How long should hoses be purged?Ch. 31 - What should be done with cylinders that have...Ch. 31 - How should the spark lighter be held to light a...Ch. 31 - Once the torch is lit, why must the acetylene flow...Ch. 31 - What type of piping can be used for a manifold...Ch. 31 - What elements make up all hydrocarbons?Ch. 31 - What are the separate parts that make up an...Ch. 31 - Use Table 31-3 to determine which fuel gas...Ch. 31 - Approximately how long would it take a 50/50...Ch. 31 - Use Table 31-4 to determine which fuel gas has the...Ch. 31 - How is acetylene produced?Ch. 31 - Why is it not safe to use acetylene above 15 psig...Ch. 31 - Use Table 31-5 to determine the largest tip...Ch. 31 - Where is the highest temperature and where is the...Ch. 31 - Use Table 31-6 to determine what would be the...Ch. 31 - What are methylacetylene-propadiene fuel gases...Ch. 31 - Use Table 31-7 to determine which oxygen fuel-gas...Ch. 31 - Which fuel gas has the strongest odor and is...Ch. 31 - What is the major advantage of using propane or...Ch. 31 - Use Table 31-8 to determine which fuel gas would...Ch. 31 - What two major safety problems does hydrogen...Ch. 31 - Why should coat hangers not be used as gas welding...Ch. 31 - Explain the significance of the AWS filler metal...
Knowledge Booster
Mechanical Engineering
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.
Recommended textbooks for you
  • Welding: Principles and Applications (MindTap Cou...
    Mechanical Engineering
    ISBN:9781305494695
    Author:Larry Jeffus
    Publisher:Cengage Learning
    Refrigeration and Air Conditioning Technology (Mi...
    Mechanical Engineering
    ISBN:9781305578296
    Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson
    Publisher:Cengage Learning
  • Welding: Principles and Applications (MindTap Cou...
    Mechanical Engineering
    ISBN:9781305494695
    Author:Larry Jeffus
    Publisher:Cengage Learning
    Refrigeration and Air Conditioning Technology (Mi...
    Mechanical Engineering
    ISBN:9781305578296
    Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson
    Publisher:Cengage Learning
    Pressure Vessels Introduction; Author: Engineering and Design Solutions;https://www.youtube.com/watch?v=Z1J97IpFc2k;License: Standard youtube license