Technician A says that the proper fluid level for a manual transmission is normally to the bottom of the filler hole. Technician B says that low lubricant levels can cause a standard transmission to clash during shifting. Who is correct?

Technician A says that the proper fluid level for a manual transmission is normally to the bottom of the filler hole. Technician B says that low lubricant levels can cause a standard transmission to clash during shifting. Who is correct?

Automotive Technology: A Systems Approach (MindTap Course List)

6th Edition

ISBN:9781133612315

Author:Jack Erjavec, Rob Thompson

Publisher:Jack Erjavec, Rob Thompson

Chapter43: Automatic Transmission And Transaxle Service

Section: Chapter Questions

Problem 1ASRQ: Technician A says that a prerequisite to accurate road-testing analysis is knowing what planetary...

See similar textbooks

Related questions

Q: single step-up spur gearbox

A: To find ; Formula and standards relevant to the single step-up spur gearbox.

Q: Technician A says when removing a transmission, the rear of the engine will usually need to be…

A: Answer

Q: The cars like Padmini and ambassador have axleless transmission in the front wheels explain how the…

A: The car like Padmini and ambassador have 5 speed manual with an overdrive transmission system. The…

Q: While discussing the fail-safe function: Technician A says that the 4WS indicator light is…

A: The statement given by technician A is correct as when the fail-safe function that is when the any…

Q: When discussing shift problems, Technician A says that worn or broken engine and transaxle mounts…

A: A chain of gears which is used to pass on the power to the wheel from the engine is called as…

Q: Technician A says that on most vehicles, the wheel/tire assembly is considered sprung weight .…

A: technician A is wrong and technician B is saying correctly.

Q: Technician A says that an in-line six-cylinder diesel engine is usually longer and heavier than a V8…

Q: Technician A says that some shift solenoids can be activated by providing a ground for the solenoid.…

A: The shift solenoid is used in the gear assembly which shifts the gear according to the desire of…

Q: In a manual transmission what are the seven steps for power flow in final drive

A: The process of shifting the power generated by the engine toward the wheels is called the…

Q: what pushes the baulk ring onto the come on the gear when the sleeve starts to move on the hub?

A: Solution: Note: Dear Student! As per our guidelines, we are only allowed to answer a single…

Q: Technician A says that on FWD vehicles, the front wheels toe-out while the rear wheels on an…

A: Toe is defined as the tilt in the wheels with respect to the straight direction. If the tilt is such…

Q: Why do we need to diagnose the transmission/transaxle failure?

A: It is very important to diagnose the transmission failures in any vehicle.There are many factors…

Q: technician a says that an oil-soaked clutch dis can cause clutch chatter technician b says that…

A: Solution:

Q: List three possible causes of a noisy bearing during clutch operation.

A: There are many types of clutch noises such as whistling or whining, rattling noises, and many more.…

Q: Insufficient clutch pedal clearance results in_ _ _ _ _ _ _ _ _ .a. gear clashing while shifting…

A: Answer is option C

Q: Technician A says that the front bearing assembly locknuts for RWD vehicles are typically heavily…

A: A high torque for maintaining the bearing adjustment is required in the FWD vehicles and not the RWD…

Q: What can throttle pressure be used for in automatic transmission?

A: The throttle pressure in an automatic transmission is used to control and lubricate the…

Q: Technician A says that broken or worn engine and transaxle mounts can cause a transaxie to have…

A: Given Transaxle problem To find Statement with is/are correct Shifting problem of transaxle can be…

Q: Technician A says the torque converter uses engine oil to provide a fluid link between engine and…

A: Given data, Torque converter and its main work and use.

Q: 108) Technician A says that engine management malfunctions may be misinterpreted as transmission…

A: Engine management malfunctions can be seen by malfunction indicator lamp . this indicator shows that…

Q: Technician A says that vacuum readings for an engine with a performance camshaft might be lower at…

A: Soln:- we know, Most of the vichles are vaccum suspended units (vaccum promoters) , which utilize a…

Q: Technician A says that negative caster provides directional stability . Technician B says that pos…

A: Caster refers to the angle of the steering axis on a vehicle wheel from the straight line of the…

Q: The clutch friction disc always rotates with the

Q: A clicking noise during transmission/transaxle operationmay be an indication of __ .a. worn…

A: Given Data : Clicking Noise Transmission operation

Q: Explain the role of shift rails and shift forks in theoperation of a transmission or transaxle.

A: In a manual transmission, shift forks align the synchronizers that change gears with the intended…

Q: structural analysis and assembly of gearbox

A: Structural Analysis of gearbox Nature of loading within the various components of a gear box is an…

Q: 128) Technician A says slide hammer pullers are usually required to remove the front pump from the…

A: A slide hammer puller is a mechanical tool with a long round shaft. It has a hammer weight slides. A…

Q: Technician A says a wheel alignment rack should include rear slip plates. Technician B says a four…

A: During the alignment lift operation, it is necessary to take off slip plates. To give a better wheel…

Q: While inspecting a planetary gear-type final drive, Technician A says blackened pinion shafts…

A: Technician A is right as blackened pinion is a sign of overloading and are used as indicators of…

Q: How can we change the pressure value of the hydraulic transmission system?

A: Hydraulic power transmission systems employ a pressurized flow to transmit the energy required to…

Q: History of manual transmission

A: The first manual gearbox was created by Emile Levassor and Louis-Rene Panhard. The original…

Q: List at least five separate checks that should be made during the visual inspection of the…

A: Checks need to be done during the visual inspection of the transmission/transaxle are:

Q: 1. What are the differences between a four-speed manual transmission and a five-speed manual…

A: The difference is given below - S.No. Four speed manual transmission Five speed manual…

Q: list five checks that should be made during the visual inspection of the parts of a…

A: The mechanism with he help of which the power generated inside the engine transmitted to the wheels…

Q: True or False? In most transmissions and transaxles,there is one synchronizer assembly for each…

A: Given Synchronizer for gear speed To find Verify the statement

Q: Technician A says that some manual transmissions use 85/90 weight gear oil or synchromesh…

A: Technician A says that some manual transmissions use 85/90 weight gear oil or synchromesh…

Q: Technician A believes the stall test damages transmissions. This includes the torque converter…

A: Stakk test is a short time full-throttle operation with the vehicle brakes fully applied and the…

Q: What tool is often needed to remove gears and synchronizer assemblies from the…

A: There are different types of tools are used to remove the gears and synchronizer assemblies from the…

Q: Which of the following screwdrivers is like a Phillips but has a flatter and blunter tip? a.Standard…

A: Given Data : Screwdrivers Phillips

Q: List five things that could cause incorrect shift times and poor shifting quality

Q: What is the importance of studying on how to pull-out and mount manual transmission?

A: Manual transmission is a mechanism that enables a vehicle driver to choose the gear ratio of his…

Q: Technician A says that play in the steering gear is the probable cause of a shimmy. Technician B…

A: please rate me positive Data given- Statement of Technician A- play in the steering gear is the…

Q: Technician A says that the front wheel bearings on atypical FWD car are pressed in and out of the…

A: Technician A has correctly stated that for a FWD (Front-wheel drive)car, the bearings are to be…

Q: technician a says that camber changes as the suspension moves up and down. technician b says that…

A: Solution: Camber Gain is a term used to designate the change in the camber angle whenever a change…

Q: The worm wheel rim is made of copper for A.Easy to manufacture B.Stable transmission C.High…

Q: 1. Torque converter it is part of brake axle clutch Automatic transmission O O

A: Dear student, According to the guidelines I am allowed to answer only one…

Concept explainers

Lubricants

Lubricant can be expressed as the substance that is applied among surfaces to control the wear and tear and improve performance. Lubricants play an essential part in the safety of machinery components like gears, shaft, linkage, cam, clutches, and many others. The quantities which affect the amount of lubricant are temperature, surrounding conditions, speed of the components, and many more.

Question

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Technician A says that shift solenoids direct fluid flow to and away from the apply devices in the transmission. Technician B says that shift solenoids are used to mechanically apply a friction brake or multiple-disc clutch assembly. Who is correct?
When discussing shift problems,Technician A says that worn or broken engine and transaxle mounts can cause a transaxle to have shifting problems.Technician B says that poor shift boot alignment can cause a transaxle to jump out of gear?
when discussing shift problems, technician A says that worn or broken engine and transaxle mounts can cause a transaxle to have shifting problems. technician b says that poor shift boot alignment can cause a transaxle to jump out of gear
When servicing transfer cases, all of the following are correct, except_____. a. it must be supported on a transmission jack or safety stands b. the chain drive and a planetary gearset must be adjusted to specifications c. visual inspections for leaks and damage are necessary d. follow the manufacturers recommendations for lubricants
Explain the role of shift rails and shift forks in the operation of a transmission or transaxle.
While servicing an AWD vehicle: Technician A checks the service information to identify the correct lubricant for the center differential. Technician B says that the same lubricant is used for the viscous coup ling, transfer case) and differentials on most vehicles. Who is correct? a. Technician A only b. Technician B only c. Both A and B d. Neither A nor B
While discussing a pressure test: Technician A says that this test is the most valuable diagnostic check for slippage when a gear is engaged. Technician B says that the test can identify the cause of late or harsh shifting. Who is correct? a. Technician A only b. Technician B only c. Both A and B d. Neither A nor B
Explanation Need. WHEN A TRANSMISSION IS IN OVERDRIVE: A. THE OUTPUT SHAFT TURNS FASTER THAN THE ENGINE. (POSSIBLE CORRECT AWNSER) B. THE INPUT AND OUTPUT SHAFTS BOTH TURN FASTER THAN THE ENGINE SPEED. (NOT CORRECT AWNSER) C. THE REAR WHEELS TURN FASTER THAN THE ENGINE. D. THE OUTPUT SHAFT TURNS SLOWER THAN THE INPUT SHAFT.
Technician A says that some manual transmissions use 85/90 weight gear oil or synchromesh transmission fluid.Technician B says that some manual transmissions use automatic transmission fluid.Who is correct?
While discussing the various types of transmissions found on today’s vehicles: Technician A says that one type is the sliding gear transmission. Technician B says that one type is the sliding collar transmission. Who is correct?
When the input and output shafts are turning at the same speed, the transmission is in ____ drive. (Don't use chatgpt )
What determines whether a conventional transmission or a transaxle is used?