Automotive Technology: A Systems Approach (MindTap Course List)
6th Edition
ISBN: 9781133612315
Author: Jack Erjavec, Rob Thompson
Publisher: Cengage Learning
expand_more
expand_more
format_list_bulleted
Concept explainers
Textbook Question
Chapter 39, Problem 11RQ
Using a lubricant that is thicker than the specified lubricant can lead to_____.
a. the gear to jump out
b. hard shifting
c. gear lockup
d. gear slippage
Expert Solution & Answer
Trending nowThis is a popular solution!
Students have asked these similar questions
what occurs in a differential during cornering?
a. the inside axle side gear turns faster than the outer axle side gear
b the case turns at the same speed as the drive shaft
c the crown gear will slow down slightly
d the pinion/spider gears rotate on the pinion shaft
Using a lubricant that is thicker than the specifiedlubricant can lead to __ .a. the gear to jump outb. hard shiftingc. gear lockupd. gear slippage
What tool is often needed to remove gears and synchronizer assemblies from the transmission/transaxle main shaft?
Chapter 39 Solutions
Automotive Technology: A Systems Approach (MindTap Course List)
Ch. 39 - After draining gear oil from a transaxie, the...Ch. 39 - Prob. 2RQCh. 39 - Prob. 3RQCh. 39 - What tool is often required to remove gears and...Ch. 39 - When removing or installing bearings, where should...Ch. 39 - List five common sources for transmission fluid...Ch. 39 - True or False? Bearing noise increases under load...Ch. 39 - A rough, growling noise that is heard from a...Ch. 39 - A clicking noise during transrnission/transaxle...Ch. 39 - Worn teeth on a speed gear can cause_______. a....
Ch. 39 - Using a lubricant that is thicker than the...Ch. 39 - What should you do to properly identify the type...Ch. 39 - Prob. 13RQCh. 39 - List at least five items that are typically...Ch. 39 - A poorly adjusted shift linkage can cause which of...Ch. 39 - Technician A says that the transmission rear seal...Ch. 39 - A noise occurs in forward and reverse gears but...Ch. 39 - A rough, growling noise occurs when a vehicle with...Ch. 39 - A car jumps out of gear into neutral, particularly...Ch. 39 - While diagnosing a noise from a transmission:...Ch. 39 - Technician A says that broken or worn engine and...Ch. 39 - While inspecting a transaxies gears: Technician A...Ch. 39 - During a test drive, a noise that appears to be...Ch. 39 - While inspecting the synchronizers of a transaxle:...Ch. 39 - Technician A says that the proper fluid level for...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- When servicing transfer cases, all of the following are correct, except_____. a. it must be supported on a transmission jack or safety stands b. the chain drive and a planetary gearset must be adjusted to specifications c. visual inspections for leaks and damage are necessary d. follow the manufacturers recommendations for lubricantsarrow_forwardTechnician A says that a gear tooth pattern identifies ring gear runout. Technician B says that gear patterns are not accurate if there is excessive ring gear runout. Who is correct? a. Technician A only b. Technician B only c. Both A and B d. Neither A nor Barrow_forwardTo achieve a slow overdrive in a simple planetary gearset, the . a.sun gear must be the input member b.ring gear must be the input member c.planetary cart"ier must be the input memberring gear must be held d. ring gear must be heldarrow_forward
- Tech A says that if a noise is caused by a set of worn gears, it will normally be loudest in that gear while driving under a load. Tech B says that if the bearings on the input shaft, countershaft, or main shaft are worn, either front or rear, a growling noise will result when stopped in gear. Who is correct?arrow_forwardprevious explanation isn't good. What is the output when a large gear drives a smaller gear ? (Answer it within 30min)arrow_forwardDiscuss the difference between simple gear train and compound gear train ..arrow_forward
- What causes suction of fluid into the gear pump? a. when pressure drops during engagement of teeth at the suction side b. when pressure increases during engagement of teeth at the suction side c. when pressure drops during disengagement of teeth at the suction side d. when pressure increases during disengagement of teeth at the suction side Clear my choicearrow_forwardIn K mechanisms, the gear wheels rotate around which circles? A.bottom teeth circle B.rolling circle C.basic circle D.exterior-top circle E.Department circlearrow_forwardA clicking noise during transrnission/transaxle operation may be an indication of ________. a. worn mainshaft (input shaft) bearings b. faulty synchronizer operation c. failed oil seals d. worn, broken, or chipped gear teetharrow_forward
- While discussing a pressure test: Technician A says that this test is the most valuable diagnostic check for slippage when a gear is engaged. Technician B says that the test can identify the cause of late or harsh shifting. Who is correct? a. Technician A only b. Technician B only c. Both A and B d. Neither A nor Barrow_forwardwhat is the equation of the addendum and dedendum in bevel geararrow_forwardExplain the operation principle of a differential system and how a differential system relates to epicyclic gear trainsarrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Automotive Technology: A Systems Approach (MindTa...Mechanical EngineeringISBN:9781133612315Author:Jack Erjavec, Rob ThompsonPublisher:Cengage Learning
Automotive Technology: A Systems Approach (MindTa...
Mechanical Engineering
ISBN:9781133612315
Author:Jack Erjavec, Rob Thompson
Publisher:Cengage Learning
Principles of Lubrication | Automobile Engineering; Author: Magic Marks;https://www.youtube.com/watch?v=MGbbSxZTdCQ;License: Standard Youtube License