Automotive Technology: A Systems Approach (MindTap Course List)
6th Edition
ISBN: 9781133612315
Author: Jack Erjavec, Rob Thompson
Publisher: Cengage Learning
expand_more
expand_more
format_list_bulleted
Concept explainers
Textbook Question
Chapter 39, Problem 15RQ
A poorly adjusted shift linkage can cause which of the following problems?
a. Gear clash
b. Hard shifting
c. The gear to jump out
d. All of the above
Expert Solution & Answer
Trending nowThis is a popular solution!
Students have asked these similar questions
A poorly adjusted shift linkage can cause whichof the following problems?a. Gear clashb. Hard shiftingc. The gear to jump outd. All of the above
When discussing shift problems,Technician A says that worn or broken engine and transaxle mounts can cause a transaxle to have shifting problems.Technician B says that poor shift boot alignment can cause a transaxle to jump out of gear?
when discussing shift problems, technician A says that worn or broken engine and transaxle mounts can cause a transaxle to have shifting problems. technician b says that poor shift boot alignment can cause a transaxle to jump out of gear
Chapter 39 Solutions
Automotive Technology: A Systems Approach (MindTap Course List)
Ch. 39 - After draining gear oil from a transaxie, the...Ch. 39 - Prob. 2RQCh. 39 - Prob. 3RQCh. 39 - What tool is often required to remove gears and...Ch. 39 - When removing or installing bearings, where should...Ch. 39 - List five common sources for transmission fluid...Ch. 39 - True or False? Bearing noise increases under load...Ch. 39 - A rough, growling noise that is heard from a...Ch. 39 - A clicking noise during transrnission/transaxle...Ch. 39 - Worn teeth on a speed gear can cause_______. a....
Ch. 39 - Using a lubricant that is thicker than the...Ch. 39 - What should you do to properly identify the type...Ch. 39 - Prob. 13RQCh. 39 - List at least five items that are typically...Ch. 39 - A poorly adjusted shift linkage can cause which of...Ch. 39 - Technician A says that the transmission rear seal...Ch. 39 - A noise occurs in forward and reverse gears but...Ch. 39 - A rough, growling noise occurs when a vehicle with...Ch. 39 - A car jumps out of gear into neutral, particularly...Ch. 39 - While diagnosing a noise from a transmission:...Ch. 39 - Technician A says that broken or worn engine and...Ch. 39 - While inspecting a transaxies gears: Technician A...Ch. 39 - During a test drive, a noise that appears to be...Ch. 39 - While inspecting the synchronizers of a transaxle:...Ch. 39 - Technician A says that the proper fluid level for...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- List five things that could cause incorrect shift times and poor shifting qualityarrow_forwardWhat can too much clutch pedal free play cause? a.hard gear shifting b.fast release bearing wear c.release fork wear d.clutch slippingarrow_forwardWhen discussing the various gear positions of a transfer case, Technician A says that when the transfer case is in low, the overall gear ratio is numerically increased. Technician B says that when the transfer case is in the high position, the vehicle operates in an overdrive mode due to the decrease in torque multiplication. Who is correct?arrow_forward
- What inputs are of prime importance to a computer in deciding when to shift gears?arrow_forwardThe four common configurations used as the finaldrives on FWD vehicles are the __ gear, __ gear,__ gear, and __arrow_forwardThe typical RWD drive shaft rotates how many times faster than wheelsarrow_forward
- Explanation Need. WHEN A TRANSMISSION IS IN OVERDRIVE: A. THE OUTPUT SHAFT TURNS FASTER THAN THE ENGINE. (POSSIBLE CORRECT AWNSER) B. THE INPUT AND OUTPUT SHAFTS BOTH TURN FASTER THAN THE ENGINE SPEED. (NOT CORRECT AWNSER) C. THE REAR WHEELS TURN FASTER THAN THE ENGINE. D. THE OUTPUT SHAFT TURNS SLOWER THAN THE INPUT SHAFT.arrow_forwardWhile inspecting a planetary gear-type final drive, Technician A says blackened pinion shafts indicate severe overloading. Technician B says bluish gears indicate overheating. Who is correct?arrow_forwardName the three drive configurations that a gearsetcan transfer torque.arrow_forward
- Technician A says that negative caster provides directional stability . Technician B says that pos caster results from excessive positive cam ber . Who is correct ?arrow_forwardTechnician A says that some systems use a special modulated shift control solenoid. Technician B says that some systems use a special modulated converter clutch control solenoid. Who is correct?arrow_forwardWhile discussing shift mechanisms: Technician A says that the interlock notches hold the transmission in the selected gear. Technician B says that the detent notches prevent the selection of more than one gear during operation. Who is correct? a. Technician A only b. Technician B only c. Both A and B d. Neither A nor Barrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Automotive Technology: A Systems Approach (MindTa...Mechanical EngineeringISBN:9781133612315Author:Jack Erjavec, Rob ThompsonPublisher:Cengage Learning
Automotive Technology: A Systems Approach (MindTa...
Mechanical Engineering
ISBN:9781133612315
Author:Jack Erjavec, Rob Thompson
Publisher:Cengage Learning
Power Transmission; Author: Terry Brown Mechanical Engineering;https://www.youtube.com/watch?v=YVm4LNVp1vA;License: Standard Youtube License