Automotive Technology: A Systems Approach (MindTap Course List)
6th Edition
ISBN: 9781133612315
Author: Jack Erjavec, Rob Thompson
Publisher: Cengage Learning
expand_more
expand_more
format_list_bulleted
Concept explainers
Videos
Textbook Question
Chapter 39, Problem 1RQ
After draining gear oil from a transaxie, the technician notices that the oil has shiny, metallic particles in it. What does this indicate?
Expert Solution & Answer
To determine
The condition it indicates if a shiny, metallic particle is draining oil from a transaxle.
Answer to Problem 1RQ
It indicates the condition of excessive wear.
Explanation of Solution
Proper lubrication is required for longer transmission/transaxle life. The lubrication gear oil should be checked and replaced after required specified intervals of time. The condition of the draining oil gives a lot of indication about the parts and components of the transmission/transaxle. Thus, while draining the gear oil if it has some golden or shiny metallic particles in it, this indicates extensive internal wear or damage in the parts of a transaxle.
Want to see more full solutions like this?
Subscribe now to access step-by-step solutions to millions of textbook problems written by subject matter experts!
Students have asked these similar questions
After draining gear oil from a transaxle, the techniciannotices that the oil has shiny, metallic particles init. What does this indicate?
Which one is correct plzz answer fast
What is Brake horsepower and where did the name come from?
Chapter 39 Solutions
Automotive Technology: A Systems Approach (MindTap Course List)
Ch. 39 - After draining gear oil from a transaxie, the...Ch. 39 - Prob. 2RQCh. 39 - Prob. 3RQCh. 39 - What tool is often required to remove gears and...Ch. 39 - When removing or installing bearings, where should...Ch. 39 - List five common sources for transmission fluid...Ch. 39 - True or False? Bearing noise increases under load...Ch. 39 - A rough, growling noise that is heard from a...Ch. 39 - A clicking noise during transrnission/transaxle...Ch. 39 - Worn teeth on a speed gear can cause_______. a....
Ch. 39 - Using a lubricant that is thicker than the...Ch. 39 - What should you do to properly identify the type...Ch. 39 - Prob. 13RQCh. 39 - List at least five items that are typically...Ch. 39 - A poorly adjusted shift linkage can cause which of...Ch. 39 - Technician A says that the transmission rear seal...Ch. 39 - A noise occurs in forward and reverse gears but...Ch. 39 - A rough, growling noise occurs when a vehicle with...Ch. 39 - A car jumps out of gear into neutral, particularly...Ch. 39 - While diagnosing a noise from a transmission:...Ch. 39 - Technician A says that broken or worn engine and...Ch. 39 - While inspecting a transaxies gears: Technician A...Ch. 39 - During a test drive, a noise that appears to be...Ch. 39 - While inspecting the synchronizers of a transaxle:...Ch. 39 - Technician A says that the proper fluid level for...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- While discussing thread sealants and lubricants: Technician A says that antiseize compound is used where a bolt might become difficult to remove after a period of time. Technician B says that thread sealants are used on bolts that are tightened into an oil cavity or coolant passage. Who is correct? Technician A Technician B Both A and B Neither A nor Barrow_forwardDescribe the proper procedure to seal a puncture in a tire.arrow_forwardAfter installing cam bearings: Technician A checks that the oi, holes in the bearings are properly aligned with those in the block by squirting oil into the holes. Technician B checks for proper alignment by inserting a wire through the holes. Who is correct? Technician A Technician B Both A and B Neither A nor Barrow_forward
- True or False? Make sure you locate and adhere to the wet torque specs when tightening a bolt that has been lubricated with oil or any other liquid.arrow_forwardWhile discussing the results of an oil pressure test: Technician A says that when the fluid pressures are high, internal leaks, a clogged filter, low oil pump out put, or a faulty pressure regulator valve are indicated. Technician B says that if the fluid pressure increased at the wrong time, an internal leak at the servo or clutch seal is indicated. Who is correct? a. Technician A only b. Technician B only c. Both A and B d. Neither A nor Barrow_forwardWhen fitting a freshly ground valve into a freshly ground seat: Technician A says that the seat should be ground more with the same stone if the margin is too small. Technician B says that the seat should be ground more with the same stone if the valve seat is too high. Who is correct?arrow_forward
- Technician A says that positive valve stem seals fit tightly around the top of the valve guide. Technician B says that positive stem seals scrape oil off the valve as it moves up and down. Who is correct? Technician A Technician B Both A and B Neither A nor Barrow_forwardWhat makes some spatter “hard?”arrow_forwardWhile inspecting the timing gears of an engine: Technician A says a gear with cracks, spalling, or excessive wear on the tooth surface indicates improper gear backlash. Technician B says the diameter of many of the engines timing gears and sprockets should be measured with the drive chain wrapped around the individual gears. Who is correct? Technician A Technician B Both A and B Neither A nor Barrow_forward
- While checking a hydraulic phaser after the camshaft has been removed from the engine: Technician A attempts to rotate the phasers timing gear by hand and replaces it if it does not move. Technician B applies air pressure to the advance and retard ports and replaces it if the gear does not move. Who is correct? Technician A Technician B Both A and B Neither A nor Barrow_forwardWhat will happen if the float in an oil separator collapses?arrow_forwardChoose correct answer: The compressor is used to increase the pressure of fluid-like air or grease. Select one: True Falsearrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Automotive Technology: A Systems Approach (MindTa...Mechanical EngineeringISBN:9781133612315Author:Jack Erjavec, Rob ThompsonPublisher:Cengage Learning
Refrigeration and Air Conditioning Technology (Mi...Mechanical EngineeringISBN:9781305578296Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill JohnsonPublisher:Cengage Learning
Precision Machining Technology (MindTap Course Li...Mechanical EngineeringISBN:9781285444543Author:Peter J. Hoffman, Eric S. Hopewell, Brian JanesPublisher:Cengage Learning
Welding: Principles and Applications (MindTap Cou...Mechanical EngineeringISBN:9781305494695Author:Larry JeffusPublisher:Cengage Learning
Automotive Technology: A Systems Approach (MindTa...
Mechanical Engineering
ISBN:9781133612315
Author:Jack Erjavec, Rob Thompson
Publisher:Cengage Learning
Refrigeration and Air Conditioning Technology (Mi...
Mechanical Engineering
ISBN:9781305578296
Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson
Publisher:Cengage Learning
Precision Machining Technology (MindTap Course Li...
Mechanical Engineering
ISBN:9781285444543
Author:Peter J. Hoffman, Eric S. Hopewell, Brian Janes
Publisher:Cengage Learning
Welding: Principles and Applications (MindTap Cou...
Mechanical Engineering
ISBN:9781305494695
Author:Larry Jeffus
Publisher:Cengage Learning
Properties of Fluids: The Basics; Author: Swanson Flo;https://www.youtube.com/watch?v=TgD3nEO1iCA;License: Standard YouTube License, CC-BY
Fluid Mechanics-Lecture-1_Introduction & Basic Concepts; Author: OOkul - UPSC & SSC Exams;https://www.youtube.com/watch?v=6bZodDnmE0o;License: Standard Youtube License