Automotive Technology
7th Edition
ISBN: 9781337794213
Author: ERJAVEC, Jack.
Publisher: Cengage,
expand_more
expand_more
format_list_bulleted
Textbook Question
Chapter 39, Problem 2MC
A clicking noise during transrnission/transaxle operation may be an indication of ________.
a. worn mainshaft (input shaft) bearings
b. faulty synchronizer operation
c. failed oil seals
d. worn, broken, or chipped gear teeth
Expert Solution & Answer
Trending nowThis is a popular solution!
Students have asked these similar questions
A clicking noise during transmission/transaxle operationmay be an indication of __ .a. worn mainshaft (input shaft) bearingsb. faulty synchronizer operationc. failed oil sealsd. worn, broken, or chipped gear teeth
What tool is often needed to remove gears and synchronizer assemblies from the transmission/transaxle main shaft?
While inspecting a planetary gear-type final drive, Technician A says blackened pinion shafts indicate severe overloading. Technician B says bluish gears indicate overheating. Who is correct?
Chapter 39 Solutions
Automotive Technology
Ch. 39 - After draining gear oil from a transaxie, the...Ch. 39 - Prob. 2SACh. 39 - Prob. 3SACh. 39 - What tool is often required to remove gears and...Ch. 39 - When removing or installing bearings, where should...Ch. 39 - List five common sources for transmission fluid...Ch. 39 - What should you do to properly identify the type...Ch. 39 - List at least five items that are typically...Ch. 39 - Prob. 1TFCh. 39 - True or False? Bearing noise increases under load...
Ch. 39 - A rough, growling noise that is heard from a...Ch. 39 - A clicking noise during transrnission/transaxle...Ch. 39 - Worn teeth on a speed gear can cause_______. a....Ch. 39 - Using a lubricant that is thicker than the...Ch. 39 - A poorly adjusted shift linkage can cause which of...Ch. 39 - Technician A says that the transmission rear seal...Ch. 39 - A noise occurs in forward and reverse gears but...Ch. 39 - A rough, growling noise occurs when a vehicle with...Ch. 39 - A car jumps out of gear into neutral, particularly...Ch. 39 - While diagnosing a noise from a transmission:...Ch. 39 - Technician A says that broken or worn engine and...Ch. 39 - Technician A says that shims may be used to adjust...Ch. 39 - During a test drive, a noise that appears to be...Ch. 39 - While inspecting the synchronizers of a transaxle:...Ch. 39 - Technician A says that the proper fluid level for...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- To achieve a slow overdrive in a simple planetary gearset, the . a.sun gear must be the input member b.ring gear must be the input member c.planetary cart"ier must be the input memberring gear must be held d. ring gear must be heldarrow_forwardWhen servicing transfer cases, all of the following are correct, except_____. a. it must be supported on a transmission jack or safety stands b. the chain drive and a planetary gearset must be adjusted to specifications c. visual inspections for leaks and damage are necessary d. follow the manufacturers recommendations for lubricantsarrow_forwardHow to draw an involute spur gear.arrow_forward
- Technician A says that a Simpson gearset is two planetary gearsets that share a common sun gear. Technician B says that a Ravigneaux gearset has two sun gears, two sets of planet gears, and a common ring gear. Who is correct? a.Technician A only b.Technician B only c.Both A and B d.Neither A or Barrow_forwardA clicking noise during transmission/transaxleoperation may be an indication of .arrow_forwardwhat occurs in a differential during cornering? a. the inside axle side gear turns faster than the outer axle side gear b the case turns at the same speed as the drive shaft c the crown gear will slow down slightly d the pinion/spider gears rotate on the pinion shaftarrow_forward
- what would cause a final drive noise that is heard only when cornering? a. Incorrect tooth pattern contact b. a broken crown gear tooth c. worn differential case gears d. a bent axle housingarrow_forwardTechnician A says that the countergear or cluster gear is actually several gears machined out of single piece of iron or steel. Technician B says that the countergear is driven by the clutch gear and drives the mainshaft speed gears. Who is correct? a. Technician A only b. Technician B only c. Both A and B d. Neither A nor Barrow_forwardA noise occurs in forward and reverse gears but not in neutral: Technician A says that the input shaft bearing may be bad. Technician B says that the mainshaft bearing may be bad. Who is correct? a. Technician A only b. Technician B only c. Both Aand B d. Neither A nor Barrow_forward
- Technician A says that a gear tooth pattern identifies ring gear runout. Technician B says that gear patterns are not accurate if there is excessive ring gear runout. Who is correct? a. Technician A only b. Technician B only c. Both A and B d. Neither A nor Barrow_forwardIn a simple planetary gearset, when the planetary carrier is held, the gearset produces a______. a. reverse b. direct drive c. fast overdrive d. forward reductionarrow_forwardWhat is ''Dynamic load analysis of spur gears"arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Automotive Technology: A Systems Approach (MindTa...Mechanical EngineeringISBN:9781133612315Author:Jack Erjavec, Rob ThompsonPublisher:Cengage LearningAutomotive TechnologyMechanical EngineeringISBN:9781337794213Author:ERJAVEC, Jack.Publisher:Cengage,
Automotive Technology: A Systems Approach (MindTa...
Mechanical Engineering
ISBN:9781133612315
Author:Jack Erjavec, Rob Thompson
Publisher:Cengage Learning
Automotive Technology
Mechanical Engineering
ISBN:9781337794213
Author:ERJAVEC, Jack.
Publisher:Cengage,
BEARINGS BASICS and Bearing Life for Mechanical Design in 10 Minutes!; Author: Less Boring Lectures;https://www.youtube.com/watch?v=aU4CVZo3wgk;License: Standard Youtube License