When removing or installing bearing, where should force be applied

Q: List five things that could cause premature bearing failure

A: No matter what, things are bound to break. The same holds for bearing. But it can be prevented by…

Q: The wrong maintenance procedure followed while performing gib adjustment on a lathe machine is O…

A: The correct maintenance procedure for gib adjustment on the lathe machine Adjust the gib to new…

Q: cker mechanism rocking angle of 70 degrees. What are the lengths of the 4 bars in inches

A: A four-bar crank-rocker mechanism rocking angle of 70 degrees. What are the lengths of the 4 bars in…

Q: What are forces on pin C and D

A:

Q: Sommerfeld number of the bearing

A: Given;A hydrodynamic  journal bearing is subjected toLoad= 2000 NRotational speed=2000 rpm bearing…

Q: an be manufactured by cast aluminum alloy only.  a. Nose Section b. Power Section c. Supercharger…

A: we have to determine which of the sections of radial engine can be manufactured by aluminum casting

Q: The roller support restricts the horizontal movements Select one: O True Eplco

A: Roller Support The roller support helps to provide a horizontal movement to the beam or bridge. It…

Q: The copper head hammer is used for releasing hold pin in the chuck.

A: Yes, It is True. The copper head hammer is used for releasing hold pin the chuck.

Q: The following device is used to hold a workpiece securely during drilling in Drilling machine Select…

A: It is required determine which of following device is used to hold a workpiece during drilling…

Q: Which of the following is considered as the purpose why bearings are lubricated? a. To protect the…

A: given: Which of the following is considered as the purpose why bearings are lubricated?

Q: Multiple choice Which wheelbarrow shown is well designed

A: Given:

Q: what parts provide for toe-out on turns

A: Toe-out on turns is a toe setting for the front wheels so that it can make turns. While making a…

Q: What tool is generally used to measure crank shaft bearing journals? a. vernier calipers b.…

A: The dial bore gauge measures the inside diameter of the round holes of crankshaft journal bearings.

Q: A revolving pillar jib cranes can rotate 360° are provided with stops at the end of the jib to…

A:

Q: What type of bearing is recommended for a dirty environment?

A:

Q: Worn teeth on a speed gear can cause?

A: worn teeth creates a big problem in gear drive.

Q: A STAR WHEEL ADJUSTER RETURN SPRINGS ANCHOR PLATE E ANCHOR PIN PLATE SPRING SPRING STAR WHEEL…

A: Backing plate - C Shoe - D Wheel cylinder - A

Q: 7) For the sliding bearing to get the best embedded and compliance features, the materials is B.…

A: 7. For the sliding bearing to get the best embedded and compliance feature, the material is Select…

Q: specification required for the bolt

A: Given; Three bolt system as shown in figure;The bolt material has ,shear yield…

Q: Industrial Main   What is the first step to installing a bearing on a shaft

A:

Q: True or False? The largest diameter threaded rod is available only up-to 8-inches

A: The threaded rod has several different measurements associated with it. There is major diameter,…

Q: Define the Crowned Nut and where is it used? Please define the shoulder nut and where is it used

A: Crown-Nuts. An Embed for utilization inside the end of the circular and square area. The Crown-nut…

Q: • Use hexagonal head screw/bolt with jam locking nut through clearance holes to fix the two parts…

A:

Q: Draw three views of the adjusting bracket. . Orill-2 Holes 3 BOrill

A: The figure below shows the top and front view of the given model.

Q: Industrial Maint. What are the three types of loads that may be placed on a bearing?

A: The three types of loads that may be placed on a bearing are

Q: Define the drill press center pulley bearing replacement.

A: solution of above problem is below:

Q: If rods are used to support a precision movement such as a positioning table, the table will ride on…

A: Precision movement of the robot’s arm is the measure of the performance in any system. In robotics…

Q: The wrong maintenance procedure followed while performing gib adjustment on a lathe machine is On…

A: The engine lathe is a high-precision machine tool that needs to be treated with care. The lathe's…

Q: What is The bearing

A: When two object are in contact and they are moving relative to each than a friction force ulcers…

Q: stiffness (in N/m) of the required mounting pad

A: Given; A precision instrument package m= 1 kgSurface vibrating at= 60 HzIsolation is designed with…

Q: 5 inch dia. shafts coupling to connect the equipment shafts. Note: use 4 bolts only nstructions:

A:

Q: Nut Screw Handle Runch

A:

Q: Helical gear

A: Ans is Helical gear

Q: force Frequired to hold the plug in its position

A: Given; Consider a frictionless, massless and leak proof plug blocking a rectangular hole of…

Q: The average bearing life is the life that 90% of bearings will achieve or exceed before they fail…

A:

Q: What are the bearing plates?

A: Bearing plates are the plates that are used between two connected members in order to strengthen and…

Q: Which of the following type of bearing do you recommend for a household appliance (criterion of…

A: Which of the following type of bearing do you recommend for a household appliance (criterion of…

Q: The inner diameter of the bearing is also known as Select one: O Nut O Bolt O Bore Shaft

A: The inner diameter of the bearing is also known as -

Q: life of the ball bearing

A: Given: If the load on a ball bearing is reduced to half, the life of the ball bearing ? Therefore;…

Q: What is the type of bearing where the load ot carris is Perpendicular to the axia of the shaft it…

A: There are two main type of bearing : thrust bearing and radial load bearing

Q: The greater the working load of the bearing, the penetration of grease should be . A. Bigger B.…

A:

Q: The wrong maintenance procedure followed while performing gib adjustment on a lathe machine is The…

A: Given: The wrong maintenance procedure followed while performing gib adjustment on a lathe machineis

Q: Which of the following arrangements is least effective in tightening the nut? rod wrench wrench nut…

A: The Force acting in each case is F. The amount of torque produced by the force F depends upon the…

Q: Differentiate enery and force

A: energy is defined as the amount of work that can be performed by force and units of the energy is…

Q: *Single rod cylinder should be double acting cylinder True O False O

A: It is false that single rod cylinder should be double acting cylinder.

Q: What is the axle pressure on the front axle (which is standing on the quay)?

A: Draw the free body diagram of the beam.

Q: The copper head hammer is used for releasing hold pin in the chuck. Select one: True False

A: The copper hear hammer is a hammer in which striking portion of the hammer (or head) are…

Q: the effect of the smooth surface equal effect roller in support

A: yes