Automotive Technology
7th Edition
ISBN: 9781337794213
Author: ERJAVEC, Jack.
Publisher: Cengage,
expand_more
expand_more
format_list_bulleted
Concept explainers
Textbook Question
Chapter 4, Problem 11MC
Technician A says that a transaxle delivers torque to the front and the rear drive axles. Technician B says that a transaxle is most commonly found in 4WD pickups and SUVs. Who is correct?
- Technician A
- Technician B
- Both A and B
- Neither A nor B
Expert Solution & Answer
Trending nowThis is a popular solution!
Students have asked these similar questions
32. Technician A says hypoid gearset are only used in RWD vehicle drivetrains. Technician B says hypoid gearset multiply torque. Which technician is correct?
A- Technician A
B- Technician B
C- Both A and B
D- Neither A nor B.
Technician A says the front wheel bearings on a typical FWD car are sealed and non-adjustable. Technician B says the front wheel bearings on a typical FWD car are greaseable and adjustable. Who is correct?
Technician A says that broken or worn engine and transaxle mounts can cause a transaxie to have shiftinf problems.Technician B says that poor shift boot alignment can cause a transaxle to jump out of gear.Who is correct?
a.Technician A only
b.Technician B only
c. both A and B
d. Neither A or nor B.
Chapter 4 Solutions
Automotive Technology
Ch. 4 - Prob. 1SACh. 4 - Explain the four strokes of the internal...Ch. 4 - In addition to the battery, what does the charging...Ch. 4 - What is meant by the term regenerative braking?Ch. 4 - Which of the following is not a common emission...Ch. 4 - Automatic transmissions use a instead of a clutch...Ch. 4 - Which of the following is not one of the strokes...Ch. 4 - Prob. 4MCCh. 4 - Which is not a common automotive fuel? Gasoline...Ch. 4 - What does the valve train do? It delivers fuel to...
Ch. 4 - Technician A says that liquid cooling an engine...Ch. 4 - Prob. 8MCCh. 4 - Which emission control system introduces exhaust...Ch. 4 - Prob. 10MCCh. 4 - Technician A says that a transaxle delivers torque...Ch. 4 - Which of the following is not part of the running...Ch. 4 - Which of the following statements about unibody...Ch. 4 - Which type of transmission uses pulleys to change...Ch. 4 - Prob. 15MCCh. 4 - What two major engine components work together to...Ch. 4 - Technician A says that an air-conditioning system...Ch. 4 - The boiling point of the coolant in an engines...Ch. 4 - While discussing the operation of air-conditioning...Ch. 4 - Prob. 20MCCh. 4 - Which of the following is not accomplished by the...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
Technician A says that a seized shift linkage may cause the transfer case to operate only in 4WD. Technician B says that a worn and loose linkage may cause a transfer case to operate only in 2WD. Who is correct? a. Technician A only b. Technician B only c. Both A and B d. Neither A nor B
arrow_forward
Technician A says that if a drive belt does not have the proper tension, it may produce squealing and chirping noises. Technician B says belt tension should be checked even if the engine has an automatic belt tensioner. Who is correct? Technician A Technician B Both A and B Neither A nor B
arrow_forward
Technician A says that the front wheel bearings on a typical FWD car are pressed in and out of the steering knuckle assembly. Technician B says that the front wheel bearings on a typical FWD may be bolted into the steering knuckle. Who is correct? a. Technician A only b. Technician B only c. Both A and B d. Neither A nor B
arrow_forward
While servicing an AWD vehicle: Technician A checks the service information to identify the correct lubricant for the center differential. Technician B says that the same lubricant is used for the viscous coup ling, transfer case) and differentials on most vehicles. Who is correct? a. Technician A only b. Technician B only c. Both A and B d. Neither A nor B
arrow_forward
Technician A says that the transmission rear seal at the driveline is particularly prone to leakage. When Technician B pushes up and down on the transmission, he says that the mounts require replacement because the case moves up and down. Who is correct? a. Technician A only b. Technician B only c. Both A and B d. Neither A nor B
arrow_forward
While discussing the possible causes for a clunking noise duiing acceleration: Technician A says that an outer CV joint could be the cause. Technician B says that insufficient runout of the drive axle may be the cause of the problem. Who is correct? a. Technician A only b. Technician B only c. Both A and B d. Neither A nor B
arrow_forward
Which of the following is part of the sprung weight ofa vehicle?a. Steering linkageb. Tiresc. Engined. All of the above
arrow_forward
While discussing the various types of transmissions found on today’s vehicles: Technician A says that one type is the sliding gear transmission. Technician B says that one type is the sliding collar transmission. Who is correct?
arrow_forward
When discussing shift problems,Technician A says that worn or broken engine and transaxle mounts can cause a transaxle to have shifting problems.Technician B says that poor shift boot alignment can cause a transaxle to jump out of gear?
arrow_forward
when discussing shift problems, technician A says that worn or broken engine and transaxle mounts can cause a transaxle to have shifting problems. technician b says that poor shift boot alignment can cause a transaxle to jump out of gear
arrow_forward
Technician A says that the use of firmer, urethane bushings in the suspension improves the vehicles road-holding ability and handling. Technician B says that firmer bushings help eliminate torque steer in some FWD vehicles. Who is correct? a. Technician A only b. Technician B only c. Both A and B d. Neither A nor B
arrow_forward
Which of the following is the most likely cause for a shudder during the engagement of a lock-up torque converter? a. A bad converter b. Worn or damaged CV or U-joints c. A worn front planetary gearset d. Loose flexplate
arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Automotive Technology: A Systems Approach (MindTa...
Mechanical Engineering
ISBN:9781133612315
Author:Jack Erjavec, Rob Thompson
Publisher:Cengage Learning
Automotive Technology: A Systems Approach (MindTa...
Mechanical Engineering
ISBN:9781133612315
Author:Jack Erjavec, Rob Thompson
Publisher:Cengage Learning
Power Transmission; Author: Terry Brown Mechanical Engineering;https://www.youtube.com/watch?v=YVm4LNVp1vA;License: Standard Youtube License