Fundamentals of Aerodynamics
6th Edition
ISBN: 9781259129919
Author: John D. Anderson Jr.
Publisher: McGraw-Hill Education
expand_more
expand_more
format_list_bulleted
Videos
Textbook Question
Chapter 4, Problem 4.11P
Consider again the NACA 2412 airfoil discussed in Problem 4.10. The airfoil is flying at a velocity of 60 m/s at a standard altitude of 3 km (see Appendix D). The chord length of the airfoil is 2 m. Calculate the lift per unit span when the angle of attack is 4°.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
4.75 An air-conditioning system is shown in Fig. P4.75 in which
air flows over tubes carrying Refrigerant 134a. Air enters
with a volumetric flow rate of 50 m³/min at 32°C, 1 bar, and
exits at 22°C, 0.95 bar. Refrigerant enters the tubes at 5 bar
with a quality of 20% and exits at 5 bar, 20°C. Ignoring heat
transfer at the outer surface of the air conditioner, and
neglecting kinetic and potential energy effects, determine at
steady state
(a) the mass flow rate of the refrigerant, in kg/min.
(b) the rate of heat transfer, in kJ/min, between the air and
refrigerant.
3
R-134a
P3 = 5 bar
x3 = 0.20
Refrigerant 134
Air
P₁ = 1 bar
T₁ =32°C 305 K
(AV), 50 m³/min
=
Air
2-P2 = 0.95 bar
T2 22°C 295 K
=
=
4
R-134a
P4 = 5 bar
T4=20°C
4.42 Steam enters a well-insulated turbine operating at steady
state at 4 MPa with a specific enthalpy of 3015.4 kJ/kg and a
velocity of 10 m/s. The steam expands to the turbine exit where
the pressure is 0.07 MPa, specific enthalpy is 2431.7 kJ/kg,
and the velocity is 90 m/s. The mass flow rate is 11.95 kg/s.
Neglecting potential energy effects, determine the power
developed by the turbine, in kW.
The two blocks A and B have weights WA = 60 lb and
WB = 10 lb. If the kinetic coefficient of friction between the
incline and block A is μk = 0.2, determine the speed of A
after it moves 3 ft down the plane starting from rest. Neglect
the mass of the cord and pulleys.
3
B
Chapter 4 Solutions
Fundamentals of Aerodynamics
Ch. 4 - Consider the data for the NACA 2412 airfoil given...Ch. 4 - Consider an NACA 2412 airfoil with a 2-m chord in...Ch. 4 - Starting with the definition of circulation,...Ch. 4 - Starting with Equation (4.35), derive Equation...Ch. 4 - Consider a thin, symmetric airfoil at 1.5 angle of...Ch. 4 - The NACA 4412 airfoil has a mean camber line given...Ch. 4 - For the airfoil given in Problem 4.6, calculate...Ch. 4 - Compare the results of Problems 4.6 and 4.7 with...Ch. 4 - Starting with Equations (4.35) and (4.43), derive...Ch. 4 - For the NACA 2412 airfoil, the lift coefficient...
Ch. 4 - Consider again the NACA 2412 airfoil discussed in...Ch. 4 - For the airfoil in Problem 4.11, calculate the...Ch. 4 - In Section 3.15 we studied the case of the lifting...Ch. 4 - The question is often asked: Can an airfoil fly...Ch. 4 - The airfoil section of the wing of the British...Ch. 4 - For the conditions given in Problem 4.15, a more...
Additional Engineering Textbook Solutions
Find more solutions based on key concepts
Convert each of the following binary representations to its equivalent base ten form: a. 101010 b. 100001 c. 10...
Computer Science: An Overview (13th Edition) (What's New in Computer Science)
Assume a telephone signal travels through a cable at two-thirds the speed of light. How long does it take the s...
Electric Circuits. (11th Edition)
The job of the _____ is to fetch instructions, carry out the operations commanded by the instructions, and prod...
Starting Out With Visual Basic (8th Edition)
17–1C A high-speed aircraft is cruising in still air. How does the temperature of air at the nose of the aircra...
Thermodynamics: An Engineering Approach
Why is the study of database technology important?
Database Concepts (8th Edition)
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- 123 12) The spring has a stiffness k = 200 N/m and an unstretched length of 0.5 m. If it is attached to the 3-kg smooth collar and the collar is released from rest at A, determine the speed of the collar when it reaches B. Neglect the size of the collar. 2 m S Z k=200 N/m B 1.5 marrow_forward11) The assembly consists of two blocks A and B which have a mass of 20 kg and 30 kg, respectively. Determine the speed of each block when B descends 1.5 m. The blocks are released from rest. Neglect the mass of the pulleys and cords. Barrow_forward8) The 1000-lb elevator is hoisted by the pulley system and motor M. If the motor exerts a constant force of 500 lb on the cable, determine the power that must be supplied to the motor at the instant the load has been hoisted s = 15 ft starting from rest. The motor has an efficiency of ε = 0.65. 0000arrow_forward
- 7) The spring has a stiffness k = 50 lb/ft and an unstretched length of 2 ft. As shown, it is confined by the plate and wall using cables so that its length is 1.5 ft. A 4-lb block is given a speed VA when it is at A, and it slides down the incline having a coefficient of kinetic friction μk = 0.2. If it strikes the plate and pushes it forward 0.25 ft before stopping, determine its speed at A. Neglect the mass of the plate and spring. Α k = 50 lb/ft 1.5 ft 3ftarrow_forward10) The 30-lb block A is placed on top of two nested springs B and C and then pushed down to the position shown. If it is then released, determine the maximum height h to which it will rise. 6 in. 4 in. kg 200 lb/in. kc 100 lb/in. Barrow_forwardAs indicated by the derivation, the principle of work and energy is valid for observers in any inertial reference frame. Show that this is so, by considering the 10-kg block which rests on the smooth surface and is subjected to a horizontal force of 6 N. If observer A is in a fixed frame x, determine the final speed of the block if it has an initial speed of 5 m/s and travels 10 m, both directed to the right and measured from the fixed frame. Compare the result with that obtained by an observer B, attached to the x' axis and moving at a constant velocity of 2 m/s relative to A. Hint: The distance the block travels will first have to be computed for observer B before applying the principle of work and energy. A B 2 m/s 5 m/s 6 N 10 marrow_forward
- 6) The block has a mass of 0.8 kg and moves within the smooth vertical slot. If it starts from rest when the attached spring is in the unstretched position at A, determine the constant vertical force F which must be applied to the cord so that the block attains a speed vB = 2.5 m/s when it reaches B; SB = 0.15 m. Neglect the size and mass of the pulley. Hint: The work of F can be determined by finding the difference Al in cord lengths AC and BC and using UF = F Al. 0.4 m -0.3 m- wwwwww k = 100 N/marrow_forwardIf the cord is subjected to a constant force of F = 300 N and the 15-kg smooth collar starts from rest at A, determine the velocity of the collar when it reaches point B. Neglect the size of the pulley. 200 mm- 200 mm B 300 mm 30° 200 mm F= 300 Narrow_forward5) The 25-lb block has an initial speed of v = 10 ft/s when it is midway between springs A and B. After striking spring B, it rebounds and slides across the horizontal plane toward spring A, etc. If the coefficient of kinetic friction between the plane and the block is μk 0.4, determine the total distance traveled by the block before it comes to rest. k₁ = 10 lb/in. 2 ft 1 ft = 10 ft/s kB = 60 lb/in. Barrow_forward
- 9) The sports car has a mass of 2.3 Mg, and while it is traveling at 28 m/s the driver causes it to accelerate at 5 m/s². If the drag resistance on the car due to the wind is FD = (0.3v²) N, where v is the velocity in m/s, determine the power supplied to the engine at this instant. The engine has a running efficiency of € = 0.68. 1=arrow_forward1) 1000 N 800 N The crate, which has a mass of 100 kg, is subjected to the action of the two forces. If it is originally at rest, determine the distance it slides in order to attain a speed of 6 m/s. The coefficient of kinetic friction between the crate and the surface is μk = 0.2. 30°arrow_forwardThe light right-angle boom which supports the 250-kg cylinder is supported by three cables and a ball-and-socket joint at O attached to the vertical x-y surface. Determine the reactions at O and the cable tensions. A Answers: C y +1.40 m! 0.70 m B 0.70 m 250 kg 1.40 m. D 1.15 m E 1.15 m 2.95 m Ox N, Oy = i N, O₂ = i TAC = i N, TBD = N, TBE = i N Narrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Principles of Heat Transfer (Activate Learning wi...Mechanical EngineeringISBN:9781305387102Author:Kreith, Frank; Manglik, Raj M.Publisher:Cengage Learning
International Edition---engineering Mechanics: St...Mechanical EngineeringISBN:9781305501607Author:Andrew Pytel And Jaan KiusalaasPublisher:CENGAGE L
Mechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage Learning
Principles of Heat Transfer (Activate Learning wi...
Mechanical Engineering
ISBN:9781305387102
Author:Kreith, Frank; Manglik, Raj M.
Publisher:Cengage Learning
International Edition---engineering Mechanics: St...
Mechanical Engineering
ISBN:9781305501607
Author:Andrew Pytel And Jaan Kiusalaas
Publisher:CENGAGE L
Mechanics of Materials (MindTap Course List)
Mechanical Engineering
ISBN:9781337093347
Author:Barry J. Goodno, James M. Gere
Publisher:Cengage Learning
Ficks First and Second Law for diffusion (mass transport); Author: Taylor Sparks;https://www.youtube.com/watch?v=c3KMpkmZWyo;License: Standard Youtube License