Steel Design (Activate Learning with these NEW titles from Engineering!)
6th Edition
ISBN: 9781337094740
Author: Segui, William T.
Publisher: Cengage Learning
expand_more
expand_more
format_list_bulleted
Question
Chapter 4, Problem 4.7.12P
To determine
(a)
The alignment chart to determine
To determine
(b)
The nominal compressive strength of member GF.
To determine
(c)
Estimate
Expert Solution & Answer
Trending nowThis is a popular solution!
Students have asked these similar questions
For the simple truss shown in the diagram, where the applied vertical downward load PP = 514 N, calculate the load in member AB (in N). Indicate a tensile load as +ve and a compressive load as -ve. Take aa = 2.7 metres.
A column is made of two Channel sections as shown. They are latticed together by light diagonal bracing. The bracing prevents them from moving independently of each other however it does not itself add to the inertia properties. The column is 480" long and is Ball and Socket supported on each end. The column is A36 steel with E = 29,000 ksi. Determine the largest axial compressive load that can be supported with a safety factor of 2.
34 - A support is a fixed, B support is a sliding joint.
loads
M= 30 kNm,
P1= 12 kN, P2= 13 kN,
q1= 6 kN ⁄ m, q2= 7 kN ⁄ m ,
spans are a= 2 m, b= 3 m.
The support reactions in the beam whose loading condition is given in the figure will be found.
Accordingly, Ax = ?A) 22.25B) 0C) None.D) 39.25E) 21/2
Chapter 4 Solutions
Steel Design (Activate Learning with these NEW titles from Engineering!)
Ch. 4 - Prob. 4.3.1PCh. 4 - Prob. 4.3.2PCh. 4 - Prob. 4.3.3PCh. 4 - Prob. 4.3.4PCh. 4 - Prob. 4.3.5PCh. 4 - Prob. 4.3.6PCh. 4 - Prob. 4.3.7PCh. 4 - Prob. 4.3.8PCh. 4 - Prob. 4.4.1PCh. 4 - Prob. 4.4.2P
Ch. 4 - Prob. 4.6.1PCh. 4 - Prob. 4.6.2PCh. 4 - Prob. 4.6.3PCh. 4 - Prob. 4.6.4PCh. 4 - Prob. 4.6.5PCh. 4 - Prob. 4.6.6PCh. 4 - Prob. 4.6.7PCh. 4 - Prob. 4.6.8PCh. 4 - Prob. 4.6.9PCh. 4 - Prob. 4.7.1PCh. 4 - Prob. 4.7.2PCh. 4 - Prob. 4.7.3PCh. 4 - Use A992 steel and select a W14 shape for an...Ch. 4 - Prob. 4.7.5PCh. 4 - Prob. 4.7.6PCh. 4 - Prob. 4.7.7PCh. 4 - The frame shown in Figure P4.7-8 is unbraced, and...Ch. 4 - Prob. 4.7.9PCh. 4 - Prob. 4.7.10PCh. 4 - Prob. 4.7.11PCh. 4 - Prob. 4.7.12PCh. 4 - Prob. 4.7.13PCh. 4 - Prob. 4.7.14PCh. 4 - Prob. 4.8.1PCh. 4 - Prob. 4.8.2PCh. 4 - Prob. 4.8.3PCh. 4 - Prob. 4.8.4PCh. 4 - Prob. 4.9.1PCh. 4 - Prob. 4.9.2PCh. 4 - Prob. 4.9.3PCh. 4 - Prob. 4.9.4PCh. 4 - Prob. 4.9.5PCh. 4 - Prob. 4.9.6PCh. 4 - Prob. 4.9.7PCh. 4 - Prob. 4.9.8PCh. 4 - Prob. 4.9.9PCh. 4 - Prob. 4.9.10PCh. 4 - Prob. 4.9.11PCh. 4 - Prob. 4.9.12P
Knowledge Booster
Similar questions
- The frame shown in Figure P4.7-8 is unbraced, and bending is about the x-axis of the members. All beams areW1835, and all columns areW1054. a. Determine the effective length factor Kx for column AB. Do not consider the stiffness reduction factor. b. Determine the effective length factor Kx for column BC. Do not consider the stiffness reduction factor. c. If Fy=50 ksi, is the stiffness reduction factor applicable to these columns?arrow_forwardA W12x79 of A573 Grade 60 (Fy = 415 MPa) steel is used as a compression member. It is 6.6 m long, fixed at the top and bottom, and has additional support in the weak direction at mid-height. Properties of the section are as follows: A = 14,500 mm^2 Ix = 258.6 x 10^6 mm^4 Iy = 84.375 x 10^6 mm^4 Calculate the effective slenderness ratio with respect to strong axis buckling using theoretical value of k.arrow_forwardA solid brass [E = 109 GPa] axial member is loaded and supported as shown. Segments (1) and (2) each have a diameter of 27 mm and segment (3) has a diameter of 13 mm. Assume L1 = 1.8 m, L2 = 1.0 m, L3 = 1.7 m, R = 38 kN, Q = 14 kN, and P = 24 kN. Determine:(a) Determine the axial force in section (2) in kN. (b) Determine the deflection of joint D (positive if downward) with respect to the fixed support at A. (c) Determine the maximum normal stress in the entire axial member. Give answer in MPa.arrow_forward
- a)Enumerate all zero force member/s.b) Calculate the internal forces of all members in kN.c) Tabulate your propose W14 section for each member showing the internal load, available strengthand its corresponding DCR value.arrow_forwardThe frame shown is subjected to lateral loads of 30 kN and 15 kN acting at joint C and B respectively. The columns are assumed to have equal cross areas. Use Cantilever Method of Analysis.a. Compute the axial load of column EFb. Compute the moment of beam BE at joint B.c. Compute the moment at the base of column AB.arrow_forwardDesign the beam to resist the loads shown using WSD Method. Take fc = 9 MPa, fs = 124 MPa, n= 11, bar diameter = 20 mm. Take b = d/2arrow_forward
- A W 360 x 744 is used as a beam to support a concrete floor system. The floor is to carry atotal load of 250 kPa. The beam is simply supported over a span of 6 m. Assume the beamis laterally supported over its length. Use A36 steel with Fy = 250 MPa. Allowabledeflection is L/360.a. Determine the center to center spacing of the beams without exceeding the allowableshear stress.b. Determine the center to center spacing of the beams without exceeding the allowablebending stress.c. Determine the center to center spacing of the beams without exceeding the allowabledeflection.arrow_forwardBADLY NEED IN 1HOUR PLS THANKYOU Above is a simple truss with P = 45.67 KN (write answers in kN in 2 decimals) Compute for the forces in: a. Member DA b. Member BH c. Member HI d. Member DG e. Member El f. Member AF g. Resultant Force Reaction of Support F (3 pts)arrow_forwardThe beam-column in the figure below is a member of a braced frame. A second-order analysis was performed with factored loads and reduced member stiffnesses to obtain the moments and axial force shown. Use LRFDand determine whether this member is adequate. Suppose that P = 165 kFor W10 x 60 with L, = 15 ft and C6 = 1.0: ф,M, = 257 ft-kips, ф,M, = 280 ft-kips;for Lc = 15 ft: cPr = 556 kips.arrow_forward
- The T-beam in the floor system has a slab thickness of 90 mm and supported by beams 6.5 m span. The beam is casts monolithically with the slab. The spacing of beams is 2 m on centers and width the web is 400 mm. The effective depth of the beam is 600 mm. It is reinforced at tension side with 8-28mm Φ bars. fc’ = 28 MPa, fy = 415 MPa 1. Which of the following most nearly give the effective width of the flange? a. 1565 mm b. 1305 mm c. 1275 mm d. 1625 mm 2. Which of the following most nearly gives the depth of compression block? a. 62.25 mm b. 52.86 mm c. 60.26 mm d. 58.29 mm 3. Which of the following gives the nominal moment capacity of the beam? a. 1461.25 kN/m b. 1156.36 kN/m c. 1163.15 kN/m d. 1172.58 kN/marrow_forwardThe single story two-bays frame is unbraced, and bending is about the x axis of each member. All beams are W16 × 57, and all columns are W10 × 100. If L1,beam = 18 ft, L2,beam = 20 ft, Ibeam = 758 in4, Lcolmns = 15 ft and Icolumn = 623 in4 . Assume the end A of a column is pinned. What are the elastic G factors for the joints A and B of the interior column?arrow_forwardDesign the W14 section column AB of the frame shown. Assume it is unbraced along the x axis andbraced in the weak y direction. The loads on the column are dead load D = 200 kips and live load L = 600kips. First determine the effective length factor K via nomographs. All girders (beams) are W16 × 100.arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Steel Design (Activate Learning with these NEW ti...Civil EngineeringISBN:9781337094740Author:Segui, William T.Publisher:Cengage Learning
Steel Design (Activate Learning with these NEW ti...
Civil Engineering
ISBN:9781337094740
Author:Segui, William T.
Publisher:Cengage Learning