Automotive Technology
7th Edition
ISBN: 9781337794213
Author: ERJAVEC, Jack.
Publisher: Cengage,
expand_more
expand_more
format_list_bulleted
Concept explainers
Textbook Question
Chapter 40, Problem 5ASRQ
While discussing the possible causes for a clunking noise duiing acceleration: Technician A says that an outer CV joint could be the cause. Technician B says that insufficient runout of the drive axle may be the cause of the problem. Who is correct?
a. Technician A only
b. Technician B only
c. Both A and B
d. Neither A nor B
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solutionStudents have asked these similar questions
Technician A says that on FWD vehicles, the front wheels toe-out while the rear wheels on an independent suspension try to toe-in as the vehicle moves ahead. Technician B says that on RWD vehicles, the front wheels tend to toe-in while the rear wheels toe-out in response to rolling resistance as suspension compliance. Who is correct?
What safety precautions must be observed when carrying out diagnosing procedure on drive shafts?
What is the purpose of of the viscous clutch?a. to engage engine otrque to the transmission.b. to improve mobility when driving conditions become difficultc. to drive both rear driving wheels when vehicle is stuck.d. to drive the rear axle assembly
Chapter 40 Solutions
Automotive Technology
Ch. 40 - Prob. 1SACh. 40 - What type of axle housing resembles a banjo?Ch. 40 - What type of axle merely supports the vehicle load...Ch. 40 - What type of floating axle has one wheel bearing...Ch. 40 - How are problems normally first noticed with the...Ch. 40 - In front-wheel drivetrains, the CV joint nearer...Ch. 40 - A CV joint that is capable of in-and-out movement...Ch. 40 - The double-offset joint is typically used in...Ch. 40 - Which type of joint has a flatter design than any...Ch. 40 - Which of these is the best way to determine which...
Ch. 40 - The single Cardan/Spicer universal joint is also...Ch. 40 - The drive shaft component that provides a means of...Ch. 40 - Large cars with long drive shafts often use a...Ch. 40 - Which type of driving axle supports the weight of...Ch. 40 - Which of the following describes the double-Cardan...Ch. 40 - Technician A says that a gear tooth pattern...Ch. 40 - Technician A says that limited-slip differential...Ch. 40 - Technician A says that side-bearing preload limits...Ch. 40 - Technician A says that a hunting gearset is one in...Ch. 40 - While discussing the possible causes for a...Ch. 40 - While diagnosing the cause of a clicking noise...Ch. 40 - Prob. 7ASRQCh. 40 - Technician A says that when a car is moving...Ch. 40 - While discussing different types of ring and...Ch. 40 - While reviewing the procedure for setting...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- Which of the following is the most likely cause for a shudder during the engagement of a lock-up torque converter? a. A bad converter b. Worn or damaged CV or U-joints c. A worn front planetary gearset d. Loose flexplatearrow_forwardAll of the following are functions of the flywheel, except it ____ . a. provides a mounting place for the clutch assembly b. smooths out cylinder firing pulsations c. has marks used to set the valve timing d. meshes with the starter drive geararrow_forwardA multilink front suspension contains which of the following? a. Strut b. Control arms c. Ball joints d. All of the abovearrow_forward
- Technician A says the front wheel bearings on a typical FWD car are sealed and non-adjustable. Technician B says the front wheel bearings on a typical FWD car are greaseable and adjustable. Who is correct?arrow_forwardWhat is benefit of bifilar suspension technique?arrow_forward32. Technician A says hypoid gearset are only used in RWD vehicle drivetrains. Technician B says hypoid gearset multiply torque. Which technician is correct? A- Technician A B- Technician B C- Both A and B D- Neither A nor B.arrow_forward
- How are problems normally first noticed with the differentialand drive axles?arrow_forwardtechnician a says that an oil-soaked clutch dis can cause clutch chatter technician b says that clutch chatter can be caused by the loose bell housing boltsarrow_forwardWhich type of driving axle supports the weightof the vehicle?a. Semifloatingb. Three-quarter floatingc. Full-floatingd. None of the abovearrow_forward
- In briefly Explain why Remaining Options are incorrect. 1)The cone clutches have become obsolete because of (a) small cone angles (b) exposure to dirt and dust (c) difficulty in disengaging (d) all of thesearrow_forwardList 5 Manual-Transmission Troubles and described each.arrow_forwardWhich of the following would not cause noise while driving in 2WD under a heavy throttle? a. Faulty ignition switch b. Worn transfer case clutch c. Inoperative locking hubs d. Bad front half shaftarrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Automotive Technology: A Systems Approach (MindTa...Mechanical EngineeringISBN:9781133612315Author:Jack Erjavec, Rob ThompsonPublisher:Cengage LearningAutomotive TechnologyMechanical EngineeringISBN:9781337794213Author:ERJAVEC, Jack.Publisher:Cengage,
Automotive Technology: A Systems Approach (MindTa...
Mechanical Engineering
ISBN:9781133612315
Author:Jack Erjavec, Rob Thompson
Publisher:Cengage Learning
Automotive Technology
Mechanical Engineering
ISBN:9781337794213
Author:ERJAVEC, Jack.
Publisher:Cengage,
Power Transmission; Author: Terry Brown Mechanical Engineering;https://www.youtube.com/watch?v=YVm4LNVp1vA;License: Standard Youtube License