Automotive Technology
7th Edition
ISBN: 9781337794213
Author: ERJAVEC, Jack.
Publisher: Cengage,
expand_more
expand_more
format_list_bulleted
Textbook Question
Chapter 40, Problem 5MC
Which of these is the best way to determine which CV joint is faulty?
a. Squeeze test
b. Runout test
c. Visual inspection
d. Road test
Expert Solution & Answer
Trending nowThis is a popular solution!
Students have asked these similar questions
Which of the following CV joint tests should be performed to determine if the CV joint needs to be serviced? a. balance test b. chassis test c. squeeze test d. spin test
A constant velocity joint that is capable of in-and-out movement is a:
Select one:
a. both fixed joint and inboard joint
b. inboard joint
c. fixed joint
d. plunge joint
Technician A says a bolt may become fatigued if it is over tightened. Technician B says that a bolt may become fatigued if it is under tightened. Who is correct?
Chapter 40 Solutions
Automotive Technology
Ch. 40 - Prob. 1SACh. 40 - What type of axle housing resembles a banjo?Ch. 40 - What type of axle merely supports the vehicle load...Ch. 40 - What type of floating axle has one wheel bearing...Ch. 40 - How are problems normally first noticed with the...Ch. 40 - In front-wheel drivetrains, the CV joint nearer...Ch. 40 - A CV joint that is capable of in-and-out movement...Ch. 40 - The double-offset joint is typically used in...Ch. 40 - Which type of joint has a flatter design than any...Ch. 40 - Which of these is the best way to determine which...
Ch. 40 - The single Cardan/Spicer universal joint is also...Ch. 40 - The drive shaft component that provides a means of...Ch. 40 - Large cars with long drive shafts often use a...Ch. 40 - Which type of driving axle supports the weight of...Ch. 40 - Which of the following describes the double-Cardan...Ch. 40 - Technician A says that a gear tooth pattern...Ch. 40 - Technician A says that limited-slip differential...Ch. 40 - Technician A says that side-bearing preload limits...Ch. 40 - Technician A says that a hunting gearset is one in...Ch. 40 - While discussing the possible causes for a...Ch. 40 - While diagnosing the cause of a clicking noise...Ch. 40 - Prob. 7ASRQCh. 40 - Technician A says that when a car is moving...Ch. 40 - While discussing different types of ring and...Ch. 40 - While reviewing the procedure for setting...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
List three items that can be checked during a visual inspection of a butt joint.
arrow_forward
What is the most common cause of leaking compression fittings? A. Cracked compression nut B. Overtightening the compression nut C. An improperly sized ring or ferrule D. Both A and C are common causes of fitting leakage
arrow_forward
(14)
Which of the following is not a factor in specifying bolts?
Select one:
A. DIAMETER
B. RADIUS
C. LENGTH
D. TYPE
arrow_forward
Which type of joint has a flatter design than anyother?a. Double-offsetb. Discc. Cross grooved. Fixed tripod
arrow_forward
What happens when the member is confined?
arrow_forward
When checking the fifth wheel, coupling device, the Certified Inspector must check the condition and the mounting to the frame. True or False?
arrow_forward
Which one of them is permanently joint type
a) keyed joint
b) pinned joint
c) nut and bolt
d ) riveted joint
arrow_forward
While discussing the different types of pressure plates: Technician A says that coil spring types are commonly used because they have strong springs. Technician B says that Belleville-type pressure plates are not commonly used because they require excessive space in the bell housing. Who is correct? a. Technician A only b. Technician B only c. Both A and B d. Neither A nor B
arrow_forward
What is the definition of a heavyweight component?
arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Automotive Technology: A Systems Approach (MindTa...
Mechanical Engineering
ISBN:9781133612315
Author:Jack Erjavec, Rob Thompson
Publisher:Cengage Learning
Welding: Principles and Applications (MindTap Cou...
Mechanical Engineering
ISBN:9781305494695
Author:Larry Jeffus
Publisher:Cengage Learning
Refrigeration and Air Conditioning Technology (Mi...
Mechanical Engineering
ISBN:9781305578296
Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson
Publisher:Cengage Learning
Automotive Technology: A Systems Approach (MindTa...
Mechanical Engineering
ISBN:9781133612315
Author:Jack Erjavec, Rob Thompson
Publisher:Cengage Learning
Welding: Principles and Applications (MindTap Cou...
Mechanical Engineering
ISBN:9781305494695
Author:Larry Jeffus
Publisher:Cengage Learning
Refrigeration and Air Conditioning Technology (Mi...
Mechanical Engineering
ISBN:9781305578296
Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson
Publisher:Cengage Learning
Differences between Temporary Joining and Permanent Joining.; Author: Academic Gain Tutorials;https://www.youtube.com/watch?v=PTr8QZhgXyg;License: Standard Youtube License