Automotive Technology
7th Edition
ISBN: 9781337794213
Author: ERJAVEC, Jack.
Publisher: Cengage,
expand_more
expand_more
format_list_bulleted
Concept explainers
Textbook Question
Chapter 42, Problem 1TF
True or False? On most late-model EAT systems, separate procedures must be followed to retrieve the DTCs from the transmission control system and the TCC system.
Expert Solution & Answer
Trending nowThis is a popular solution!
Students have asked these similar questions
True or False? In most transmissions and transaxles,there is one synchronizer assembly for each speedgear
what allows the stator to operate correctly during vortex and rotary flow
1. the torque converter clutch
2. an overrruning clutch
3. governoer pressue
4. throttle pressue
In a typical all wheel drive automatic transaxle, what controls the transfer clutch?a. Transmission control unit operating the pressure regualtor valveb. Engine computer controlling the line pressure to the various clutches in transmissionc. Transmission control unit and the duty solenoidd. Front axle speed sensor and vehicle speed sensor.
Chapter 42 Solutions
Automotive Technology
Ch. 42 - While discussing the CVT transaxie used in Toyota...Ch. 42 - Although computers receive different information...Ch. 42 - What happens if the TCM determines that the...Ch. 42 - Prob. 4SACh. 42 - List five things that could cause incorrect shift...Ch. 42 - Most late-model transmission control systems have...Ch. 42 - What inputs are of prime importance to a computer...Ch. 42 - What are the advantages of using electronic...Ch. 42 - Voltage generation devices are typically used to...Ch. 42 - True or False? On most late-model EAT systems,...
Ch. 42 - True or False? The neutral safety switch and...Ch. 42 - Which of the following is not a voltage-generating...Ch. 42 - A glitch appears in the waveform of a vehicle...Ch. 42 - Prob. 3MCCh. 42 - Which of the following would probably not be...Ch. 42 - Technician A says that some systems use a special...Ch. 42 - Technician A says that shift solenoids direct...Ch. 42 - Technician A says that throttle position is an...Ch. 42 - Technician A says that a faulty TP sensor can...Ch. 42 - Technician A says that some shift solenoids can be...Ch. 42 - An electronically controlled transmission has...Ch. 42 - While discussing transmission adaptive learning:...Ch. 42 - While discussing valve body assemblies in...Ch. 42 - A transmission has delayed upshifts under all...Ch. 42 - While diagnosing the cause of TCC shudder:...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- True or False? The neutral safety switch and reverse lamp switch are typically part of a digital transmission range sensor.arrow_forwardWhich of the following is the least likely cause of a no-start condition? Faulty CKP sensor Faulty KS Fuel or ignition system faults Faulty PCM wiringarrow_forwardTrue or False? In a high-speed CAN system, a serial data bus is used to allow communication between the various control modules in a vehicle.arrow_forward
- Most late-model transmission control systems have adaptive learning. What does this mean?arrow_forwardTrue or False? On some engines, if the gap between the crankshaft sensor and its trigger wheel is outside specifications, the sensor should be replaced.arrow_forwardWhile diagnosing the cause of TCC shudder: Technician A checks the fluid pressure sent to the clutch. Technician B says that because the shudder occurs only after the clutch is engaged, the problem is the engine, transmission, or another component of the driveline. Who is correct?arrow_forward
- A clicking noise during transmission/transaxleoperation may be an indication of .arrow_forwardWhich of the following could cause the 4WD indicators not to operate correctly? a. A faulty control module (PCM) b. Inoperative locking hubs C. Worn transfer case clutch d. Damaged transfer case shift leverarrow_forwardWhile discussing AWD systems: Technician A says that some systems are electronically controlled and use an electromagnetic clutch to engage and disengage the drive axles. Technician B says that some cars do not use a transfer case, but they are equipped with a third differential unit. Who is correct? a. Technician A only b. Technician B only c. Both A and B d. Neither A nor Barrow_forward
- Technician A says that the enable criteria are the criteria that must be met before the PCM completes a monitor test. Technician B says that a drive cycle includes operating the vehicle under specific conditions so that a monitor test can be completed. Who is correct? Technician A Technician B Both A and B Neither A nor Barrow_forwardWhich of the following would probably not be caused by a plugged filter screen at a solenoid? a. Erratic shifting b. No shift conditions c. A solenoid that will not energize d. Wrong gear startsarrow_forwardTechnician A says that if a drive belt does not have the proper tension, it may produce squealing and chirping noises. Technician B says belt tension should be checked even if the engine has an automatic belt tensioner. Who is correct? Technician A Technician B Both A and B Neither A nor Barrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Automotive Technology: A Systems Approach (MindTa...Mechanical EngineeringISBN:9781133612315Author:Jack Erjavec, Rob ThompsonPublisher:Cengage LearningAutomotive TechnologyMechanical EngineeringISBN:9781337794213Author:ERJAVEC, Jack.Publisher:Cengage,
Automotive Technology: A Systems Approach (MindTa...
Mechanical Engineering
ISBN:9781133612315
Author:Jack Erjavec, Rob Thompson
Publisher:Cengage Learning
Automotive Technology
Mechanical Engineering
ISBN:9781337794213
Author:ERJAVEC, Jack.
Publisher:Cengage,
The Robot Revolution: The New Age of Manufacturing | Moving Upstream; Author: Wall Street Journal;https://www.youtube.com/watch?v=HX6M4QunVmA;License: Standard Youtube License