While discussing valve body assemblies in late-model transmissions: Technician A says that the valve body is no longer needed in some electronically controlled transmissions. Technician B says that an EPC solenoid maintains constant fluid pressure through the valve body regardless of the vehicle’s operating condition. Who is correct?

While discussing valve body assemblies in late-model transmissions: Technician A says that the valve body is no longer needed in some electronically controlled transmissions. Technician B says that an EPC solenoid maintains constant fluid pressure through the valve body regardless of the vehicle’s operating condition. Who is correct?

Automotive Technology: A Systems Approach (MindTap Course List)

6th Edition

ISBN:9781133612315

Author:Jack Erjavec, Rob Thompson

Publisher:Jack Erjavec, Rob Thompson

Chapter43: Automatic Transmission And Transaxle Service

Section: Chapter Questions

Problem 10ASRQ: While discussing the cause of aerated fluid in a transmission: Technician A says that this can be...

See similar textbooks

Similar questions

While diagnosing the cause of TCC shudder: Technician A checks the fluid pressure sent to the clutch. Technician B says that because the shudder occurs only after the clutch is engaged, the problem is the engine, transmission, or another component of the driveline. Who is correct?
How can we change the pressure value of the hydraulic transmission system?
Technician A says that rotary oil flow is the oil flow around the circumference of the torque convertercaused by the rotation of the torque converter on its axis. Technician B says that the centrifugal lockup clutch is the type installed in most automatic transmissions. Who is correct? a. Technician A only b. Technician B only c. Both A and B d. Neither A nor B
True or False? If the fluid reservoir for a hydraulic clutch is low, the entire system should be checked for fluid leaks.
Technician A says that changes in engine load cause changes in hydraulic pressure inside the transmission. Technician B says that engine load is monitored by throttle pedal movement or by engine vacuum. Who is correct? a. Technician A only b. Technician B only c. Both A and B d. Neither A nor B
Which of the following would not cause noise while driving in 2WD under a heavy throttle? a. Faulty ignition switch b. Worn transfer case clutch c. Inoperative locking hubs d. Bad front half shaft
Technician A says that delayed shifting can be caused by worn planetary gearset members. Technician B says that delayed shifts or slippage may be caused by leaking hydraulic circuits or sticking spool valves in the valve body. Who is correct? a. Technician A only b. Technician B only c. Both A and B d. Neither A nor B
When rebuilding an automatic transmission, which of the following is not true? a. All pumps, valve bodies, and cases should be checked for warpage and should be flat filed to take off any high spots or burrs prior to reassembly. b. Only use lint-free rags to wipe parts off. c. Lubricate all thrust washers, bearings, and bush ings before installing them. d. Soak all friction materials in clean engine oil prior to installing them.
While discussing the results of an oil pressure test: Technician A says that when the fluid pressures are high, internal leaks, a clogged filter, low oil pump out put, or a faulty pressure regulator valve are indicated. Technician B says that if the fluid pressure increased at the wrong time, an internal leak at the servo or clutch seal is indicated. Who is correct? a. Technician A only b. Technician B only c. Both A and B d. Neither A nor B
While discussing the cause of aerated fluid in a transmission: Technician A says that this can be caused by too much ATF in the transmission. Technician B says that this can be caused by too little ATF in the transmission. Who is correct? a. Technician A only b. Technician B only c. Both A and B d. Neither A nor B
Question: How can we change the pressure valve of the hydraulic transmission system?
Technician A says that shift solenoids direct fluid flow to and away from the apply devices in the transmission. Technician B says that shift solenoids are used to mechanically apply a friction brake or multiple-disc clutch assembly. Who is correct?