Automotive Technology: A Systems Approach (MindTap Course List)
6th Edition
ISBN: 9781133612315
Author: Jack Erjavec, Rob Thompson
Publisher: Cengage Learning
expand_more
expand_more
format_list_bulleted
Concept explainers
Textbook Question
Chapter 43, Problem 13RQ
When rebuilding an automatic transmission, which of the following is not true?
a. All pumps, valve bodies, and cases should be checked for warpage and should be flat filed to take off any high spots or burrs prior to reassembly.
b. Only use lint-free rags to wipe parts off.
c. Lubricate all thrust washers, bearings, and bush ings before installing them.
d. Soak all friction materials in clean engine oil prior to installing them.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solutionStudents have asked these similar questions
37- Technician A says that all transmission opening pressure are derived from the regulated output flow of the oil pump. Technician B says that every automatic transmission uses one, or more, pressure regulator valves. Who is correct?
A- Technician A
B- Technician B
C- Both A and B
D- Neither A nor B
when discussing shift problems, technician A says that worn or broken engine and transaxle mounts can cause a transaxle to have shifting problems. technician b says that poor shift boot alignment can cause a transaxle to jump out of gear
When discussing shift problems,Technician A says that worn or broken engine and transaxle mounts can cause a transaxle to have shifting problems.Technician B says that poor shift boot alignment can cause a transaxle to jump out of gear?
Chapter 43 Solutions
Automotive Technology: A Systems Approach (MindTap Course List)
Ch. 43 - What is the most probable cause of a low fluid...Ch. 43 - What does milky colored ATF indicate?Ch. 43 - What do varnish or gum deposits on the dipstick...Ch. 43 - Typically during a pressure test, the pressure...Ch. 43 - What should you do if a valve does not move freely...Ch. 43 - Which of the following is the most likely cause...Ch. 43 - Ifa transmission does not have a dipstick, how do...Ch. 43 - What is checked during a stall test?Ch. 43 - When should the ATF level be checked on most...Ch. 43 - List five reasons for replacing a torque...
Ch. 43 - Pressure readings reveal possible problems in...Ch. 43 - Which of the following is a probable cause for a...Ch. 43 - When rebuilding an automatic transmission, which...Ch. 43 - Explain why oil circuit diagrams are invaluable...Ch. 43 - Explain how a plugged fluid cooler can cause a...Ch. 43 - Technician A says that a prerequisite to accurate...Ch. 43 - While discussing proper band adjustment...Ch. 43 - Technician A says that if the shift for all...Ch. 43 - Technician A says that the only positive way to...Ch. 43 - Technician A says that delayed shifting can be...Ch. 43 - While checking the condition of a cars ATF:...Ch. 43 - While discussing the results of an oil pressure...Ch. 43 - While discussing a pressure test: Technician A...Ch. 43 - While checking the engine and transmission mounts...Ch. 43 - While discussing the cause of aerated fluid in a...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- When servicing transfer cases, all of the following are correct, except_____. a. it must be supported on a transmission jack or safety stands b. the chain drive and a planetary gearset must be adjusted to specifications c. visual inspections for leaks and damage are necessary d. follow the manufacturers recommendations for lubricantsarrow_forwardList two causes that may lead to auger wobble.arrow_forwardTechnician A says that the proper fluid level for a manual transmission is normally to the bottom of the filler hole. Technician B says that low lubricant levels can cause a standard transmission to clash during shifting. Who is correct?arrow_forward
- Technician A says that rotary oil flow is the oil flow around the circumference of the torque convertercaused by the rotation of the torque converter on its axis. Technician B says that the centrifugal lockup clutch is the type installed in most automatic transmissions. Who is correct? a. Technician A only b. Technician B only c. Both A and B d. Neither A nor Barrow_forwardTrue or false Gears and crankshaft are transmitting type of short distance power type of transmissionarrow_forwardWhat provisions are usually included on tractor engines to aid in the correct timing of the camshaft?arrow_forward
- Technician A says check balls are often used to block holes between the transmission valve body and the spacer plate. Technician B says spacer plates may be installed between the transmission valve body and case. Who is right?arrow_forwardWhich of the following is probably not the cause of avibrating clutch?a. Excessive crankshaft end playb. Out-of-balance pressure plate assemblyc. Excessive flywheel runoutd. Loose flywheel boltsarrow_forwardhow will a vehicle handle if it has too much toe-out?arrow_forward
- True or False? The first step in removing an engine is usually the removal of the intake and exhaust manifolds.arrow_forwardWhich of the following statements about preparing to assemble an engine is not true? Discard and replace all bolts that are damaged. Identify what bolts go into the specific bores. Use a thread locker on all bolts. Clean bolt and cylinder block threads with a thread chaser or tap.arrow_forwardTrue or False? The camshaft is always located in the engine block.arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Automotive Technology: A Systems Approach (MindTa...Mechanical EngineeringISBN:9781133612315Author:Jack Erjavec, Rob ThompsonPublisher:Cengage LearningAutomotive TechnologyMechanical EngineeringISBN:9781337794213Author:ERJAVEC, Jack.Publisher:Cengage,Refrigeration and Air Conditioning Technology (Mi...Mechanical EngineeringISBN:9781305578296Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill JohnsonPublisher:Cengage Learning
Automotive Technology: A Systems Approach (MindTa...
Mechanical Engineering
ISBN:9781133612315
Author:Jack Erjavec, Rob Thompson
Publisher:Cengage Learning
Automotive Technology
Mechanical Engineering
ISBN:9781337794213
Author:ERJAVEC, Jack.
Publisher:Cengage,
Refrigeration and Air Conditioning Technology (Mi...
Mechanical Engineering
ISBN:9781305578296
Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson
Publisher:Cengage Learning
Mechanical Design (Machine Design) Clutches, Brakes and Flywheels Intro (S20 ME470 Class 15); Author: Professor Ted Diehl;https://www.youtube.com/watch?v=eMvbePrsT34;License: Standard Youtube License