Automotive Technology: A Systems Approach (MindTap Course List)
6th Edition
ISBN: 9781133612315
Author: Jack Erjavec, Rob Thompson
Publisher: Cengage Learning
expand_more
expand_more
format_list_bulleted
Concept explainers
Textbook Question
thumb_up100%
Chapter 43, Problem 7ASRQ
While discussing the results of an oil pressure test: Technician A says that when the fluid pressures are high, internal leaks, a clogged filter, low oil pump out put, or a faulty pressure regulator valve are indicated. Technician B says that if the fluid pressure increased at the wrong time, an internal leak at the servo or clutch seal is indicated. Who is correct?
a. Technician A only
b. Technician B only
c. Both A and B
d. Neither A nor B
Expert Solution & Answer
Trending nowThis is a popular solution!
Students have asked these similar questions
An oil leak at the bellows of a rack and pinion could be caused by ______.
Technician A says that excessive engine oil consumption can be caused by low oil levels. Technician B says that excessive oil consumption can be caused by worn valve guides. Who is correct?
When fitting a freshly ground valve into a freshly ground seat: Technician A says that the seat should be ground more with the same stone if the margin is too small. Technician B says that the seat should be ground more with the same stone if the valve seat is too high. Who is correct?
Chapter 43 Solutions
Automotive Technology: A Systems Approach (MindTap Course List)
Ch. 43 - What is the most probable cause of a low fluid...Ch. 43 - What does milky colored ATF indicate?Ch. 43 - What do varnish or gum deposits on the dipstick...Ch. 43 - Typically during a pressure test, the pressure...Ch. 43 - What should you do if a valve does not move freely...Ch. 43 - Which of the following is the most likely cause...Ch. 43 - Ifa transmission does not have a dipstick, how do...Ch. 43 - What is checked during a stall test?Ch. 43 - When should the ATF level be checked on most...Ch. 43 - List five reasons for replacing a torque...
Ch. 43 - Pressure readings reveal possible problems in...Ch. 43 - Which of the following is a probable cause for a...Ch. 43 - When rebuilding an automatic transmission, which...Ch. 43 - Explain why oil circuit diagrams are invaluable...Ch. 43 - Explain how a plugged fluid cooler can cause a...Ch. 43 - Technician A says that a prerequisite to accurate...Ch. 43 - While discussing proper band adjustment...Ch. 43 - Technician A says that if the shift for all...Ch. 43 - Technician A says that the only positive way to...Ch. 43 - Technician A says that delayed shifting can be...Ch. 43 - While checking the condition of a cars ATF:...Ch. 43 - While discussing the results of an oil pressure...Ch. 43 - While discussing a pressure test: Technician A...Ch. 43 - While checking the engine and transmission mounts...Ch. 43 - While discussing the cause of aerated fluid in a...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- True or False? If the fluid reservoir for a hydraulic clutch is low, the entire system should be checked for fluid leaks.arrow_forward37- Technician A says that all transmission opening pressure are derived from the regulated output flow of the oil pump. Technician B says that every automatic transmission uses one, or more, pressure regulator valves. Who is correct? A- Technician A B- Technician B C- Both A and B D- Neither A nor Barrow_forwardtechnician a says that an oil-soaked clutch dis can cause clutch chatter technician b says that clutch chatter can be caused by the loose bell housing boltsarrow_forward
- Technician A says that a stator aids in directing the flow of fluid from the impeller to the turbine. Technician B says that a stator is equipped with a one-way clutch that allows it to remain stationary when necessary. Who is correct?arrow_forwardWhile discussing the cause of an oil leak in an axle housing, Technician A says if the fluid leaks past the threads of the drive pinion nut, the leak can be corrected by installing a copper washer under the nut. Technician B says fluid leakage past the stud nuts that hold the carrier assembly to the axle housing can be corrected by applying thread or gasket sealer on the threads and tightening the nuts to specifications. Who is correct?arrow_forwardAn injector balance test requires an injector pulse tester and a _____ .arrow_forward
- Technician A says it is not necessary to measure valve stem height unless the valves have been replaced. Technician B says valve stem height can be adjusted with shims. Who is correct? Technician A Technician B Both A and B Neither A nor Barrow_forwardTechnician A says that some shift solenoids can be activated by providing a ground for the solenoid. Technician B says that some shift solenoids can be activated by applying hydraulic pressure to their valve. Who is correct?arrow_forwardTrue or False? Oil pressure is determined bywhether the pump is a gear type or rotor typeand by oil clearances, the pump’s pressure regulator valve, and oil viscosity.arrow_forward
- the metring valve portion of combination valve fails .technician A says that this means the entire combination valve must be replaced.Technician B says that the metring part can be repaired who is correct?arrow_forwardWhich of the following is not a type of valve guide seal? Positive Negative Umbrella O-ringarrow_forwardTechnician A says that positive valve stem seals fit tightly around the top of the valve guide. Technician B says that positive stem seals scrape oil off the valve as it moves up and down. Who is correct? Technician A Technician B Both A and B Neither A nor Barrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Automotive Technology: A Systems Approach (MindTa...Mechanical EngineeringISBN:9781133612315Author:Jack Erjavec, Rob ThompsonPublisher:Cengage LearningAutomotive TechnologyMechanical EngineeringISBN:9781337794213Author:ERJAVEC, Jack.Publisher:Cengage,Welding: Principles and Applications (MindTap Cou...Mechanical EngineeringISBN:9781305494695Author:Larry JeffusPublisher:Cengage Learning
- Refrigeration and Air Conditioning Technology (Mi...Mechanical EngineeringISBN:9781305578296Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill JohnsonPublisher:Cengage Learning
Automotive Technology: A Systems Approach (MindTa...
Mechanical Engineering
ISBN:9781133612315
Author:Jack Erjavec, Rob Thompson
Publisher:Cengage Learning
Automotive Technology
Mechanical Engineering
ISBN:9781337794213
Author:ERJAVEC, Jack.
Publisher:Cengage,
Welding: Principles and Applications (MindTap Cou...
Mechanical Engineering
ISBN:9781305494695
Author:Larry Jeffus
Publisher:Cengage Learning
Refrigeration and Air Conditioning Technology (Mi...
Mechanical Engineering
ISBN:9781305578296
Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson
Publisher:Cengage Learning
Pressure Vessels Introduction; Author: Engineering and Design Solutions;https://www.youtube.com/watch?v=Z1J97IpFc2k;License: Standard youtube license