Automotive Technology: A Systems Approach (MindTap Course List)
6th Edition
ISBN: 9781133612315
Author: Jack Erjavec, Rob Thompson
Publisher: Cengage Learning
expand_more
expand_more
format_list_bulleted
Concept explainers
Question
Chapter 45, Problem 15RQ
To determine
The blank regarding the location of the recommended tire inflation pressure.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
what is the formula to measure gas from tire interior?
what the tire wear pattern will result from excessive negative chamber?
All of the following statements are correct except?a. Tire inflation pressure directly affects traction.b. The recommended tire pressure for front andrear tires may be different.c. The recommended tire pressures are oftenlower than maximum pressures.d. The recommended tire pressure is moldedinto the sidewall of the tire
Chapter 45 Solutions
Automotive Technology: A Systems Approach (MindTap Course List)
Ch. 45 - List five things that could cause premature...Ch. 45 - Define lateral and radial runout.Ch. 45 - Prob. 3RQCh. 45 - Define dynamic and static wheel balance.Ch. 45 - Describe the proper procedure to seal a puncture...Ch. 45 - The rim offset is the vertical distance between...Ch. 45 - Prob. 7RQCh. 45 - True or False? All TPMS have a pressure sensor...Ch. 45 - A tire that wobbles from side-to-side is said to...Ch. 45 - A front tire has excessive wear on both edges of...
Ch. 45 - All of the following statements are correct...Ch. 45 - All of the following statements are correct...Ch. 45 - Which of the following statements about sidewall...Ch. 45 - All of these statements about improper wheel...Ch. 45 - Prob. 15RQCh. 45 - Technician A says that the front wheel bearings on...Ch. 45 - Technician A says that dynamic wheel imbalance...Ch. 45 - Technician A says that front bearing assembly...Ch. 45 - Technician A says that replacement wheel rims...Ch. 45 - Prob. 5ASRQCh. 45 - While choosing the correct tire for a vehicle:...Ch. 45 - Technician A says that on most vehicles, the...Ch. 45 - Prob. 8ASRQCh. 45 - Prob. 9ASRQCh. 45 - Prob. 10ASRQ
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- How does a technician determine the proper inflation for a vehicle's tires?arrow_forwardWhich of the following statements about sidewall markings is correct? a. The load index is given as a letter. b. The traction and temperature ratings are based on the speed rating of the tire. c. The tires recommended inflation pressure and load are indicated. d. The DOT code indicates when and where the tire was made.arrow_forwardWhile performing a prealignment inspection: Technician A says that improper front-wheel bearing adjustment may affect wheel alignment angles. Technician B says that worn ball joints affect only the camber angle. Who is correct? Technician A only Technician B only Both A and B Neither A nor Barrow_forward
- Technician A says that on most vehicles, the wheel/tire assembly is considered sprung weight . Technician B says that low unsprung weight makes the vehicle handle better on irreg ular surfaces. Who is correct?arrow_forwardWhat tyre wear pattern will result from excessive negative camber?(Automotive cert.4)arrow_forwardAn indirect TPMS is being discussed. Technician A says that if a specific tire is low, the system will typically alert the driver which tire is low. Technician B says that after serving the indirect TPMS, you need to perform a re-learn procedure. Who is correct? Technician A Technician B Both Technician A and B Neither Technician A or Barrow_forward
- Technician A says that replacement wheel rims should be the same as the original equipment wheels in load capacity, offset, width, diameter, and mounting configuration. Technician B says that if wheels are installed that have a different stock width or diameter, make sure to use a tire that has the same overall width as the original tires. Otherwise the vehicles wheel-speed sensors, speedometer, antiock brake system, and many other systems will be affected. Who is correct? a. Technician A only b. Technician B only c. Both A and B Neither A nor Barrow_forwardAll of the following statements are correct except? a. Tire inflation pressure directly affects traction. b. The recommended tire pressure for front and rear tires may be different. c. The recommended tire pressures are often lower than maximum pressures. d. The recommended tire pressure is molded into the sidewall of the tire.arrow_forwardA front tire has excessive wear on both edges ofthe tire tread. The most likely cause of this problem is ___.a. overinflationb. underinflationc. improper static balanced. improper dynamic balancearrow_forward
- While discussing pull during braking: Technician A says that this can be caused by one tire being underinflated. Technician B says that a frozen wheel cylinder on one side of the car can cause this. Who is correct? Technician A only Technician B only Both A and B Neither A nor Barrow_forwardWhile diagnosing the cause of noise from a transfer case: Technician A says that a probable cause is incorrect tire size. Technician B says that the most probable cause is a faulty bearing or gear. Who is correct? a. Technician A only b. Technician B only c. Both A and B d. Neither A nor Barrow_forwardWhich of the following would NOT be cause for rejection when checking the tire condition? Any tire has a fabric break or cut exposing ply or cord or any tire is in contact with the body or frame. Any tire tread or recap is separated or any tire is flat. All of the statements shown are cause for rejection. Any tire has any bumps, bulges, or knots or is repaired with a boot or blowout patch.arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Automotive Technology: A Systems Approach (MindTa...Mechanical EngineeringISBN:9781133612315Author:Jack Erjavec, Rob ThompsonPublisher:Cengage Learning
Automotive TechnologyMechanical EngineeringISBN:9781337794213Author:ERJAVEC, Jack.Publisher:Cengage,
Automotive Technology: A Systems Approach (MindTa...
Mechanical Engineering
ISBN:9781133612315
Author:Jack Erjavec, Rob Thompson
Publisher:Cengage Learning
Automotive Technology
Mechanical Engineering
ISBN:9781337794213
Author:ERJAVEC, Jack.
Publisher:Cengage,