Q: 4) Select ALL choices which may be indirectly controlled by Surface Profile IF NO DATUMS ARE USED A…

A: Surface Flatness  Perpendicularity

Q: A rotameter can be installed either vertically or horizontally for measuring water flow rate. True…

A: Rotameter A rotameter is a flow meter device that measures the volumetric flow rate of a gas or…

Q: Describe How to mesh irregular volume by using ANSYS?

A: To mesh a volume with all hexahedron elements, the following conditions must be satisfied; 1.The…

Q: Procedure on how to make the head of a meat tenderizer.

A: The procedure to make the head of a meat tenderizer is as follows: Step 1: Cutting a pattern of a…

Q: C -25 f Ray A 10 ft → D] RAy 1300 lbs

A: A basic configuration, consisting of three members joined together is called the frame. The main…

Q: Drive Shaft G-Codes programming process

A: Given question: Drive Shaft G Code programming process. The given question is related to…

Q: ased. What is the speed of the boat?

A: To determine the boat speed

Q: 2 cosh(lnx)

A: to find: 2cosh(lnx)

Q: ane area is

A:

Q: a large piece of 1 vo sections: hem cutting m machining jet machining

A: Required  Which is the correct method for cutting of steel plate

Q: provide Orthographic view

A: Question fig.

Q: Name the six basic components required in a hydraulic circuit.

A: Define : the six component required in a hydraulic circuit .

Q: ulties

A: note : according to bartleby guidelines we can solve only first question for you please repost other…

Q: Which of the following flow meters is not suitable for very low flow rate? magnetic paddle wheel…

A: Given Flow meters To find Determine the flow meter among the option which are not suitable for very…

Q: Q-2 What is the value of the Ely 400 N| 400 N/m 3m 1m A 1m

A:

Q: о ре cional area

A:

Q: Depth only

A: Option (a) is correct.  Depth only

Q: QUESTION 3 Code for a clockwise circular move to an end point that is 1 inch over in the X direction…

A: consider the following diagram:

Q: if Op1 is 18.6 °ccw, then Os1 is . CW

A:

Q: The energy loss due to the immediate increase of pipe diameter a known as a minor loss. Select one:…

A: Given Data⇒ Energy loss due to the sudden increase of pipe diameter among fluid particals.

Q: s (m) ,s = - -2t + 2 - 1 (s) 2.

A: Given data:-    s= -2t+2 (m)  Draw velocity and acceleration diagram with respect to time

Q: Given'- u= 35mls V = om/s t-5secs S-2

A:

Q: pipe carries deion is capped (Figure ed to the end of t

A: given:pressure P=50psid=0.75int=0.5in

Q: The discharge over a triangular no

A: Given data : Discharge =Q Acceleration due to gravity=g Head =h Coefficient of diacharge=Cd

Q: 5 kip/ft 15 kip ft 15 kip · ft B- 6 ft 10 ft 6 ft

A: Given figure:

Q: ion 3 plain the importance of: rake angle relief angle nose radius

A:

Q: Can u calculate the total surface area of plain washer

A: Given:Inner radius,di=6.45 mmOuter radius,do=13.35 mmthickness,t=2.10 mm

Q: Discuss three ways to remove water from the air in an air distribution system.

A: Moisture is ever present in the atmosphere. It can affect air distribution systems by affecting…

Q: ke angle is 0°. The minimum value of sh

A:

Q: What does the shear flow measure?

A: The shear flow is defined as the shear force per unit length in a thin walled perimeter. The…

Q: what is the change in pipe diameter ca

A: To find Change in pipe diameter caused by internal pressure.

Q: Datum head or potential head can be presented by:

A: Datum is a reference plane from which the potential head is shown.

Q: Which one of the following statement is correct for steam nozzle? O a. Outlet velocity of the steam…

A: Let us first understand how steam nozzle works: Steam nozzles are generally used in power plants…

Q: List at least 5 non-destructive technique normally used for productive maintenance

A: Non-Destructive Testing (NDT): It is a type of inspection methods in which the inspectors inspect…

Q: Different types of altimeters

A: TO BE EXPLAIN- Different types of altimeter. Altimeter is a device which measures the altitude of…

Q: etermine the minimum clearance in the assembly.

A: To determine the minimum clearance in the assembly.

Q: Which of the following does not help in collecting results in the mechanic Select one: O a. Pressure…

A: Given Data⇒ Mechanical heat pump

Q: True or False? All rectangular x-sections less than 12-inch in width and less than 0.23-inch in…

A: The minimum width for the all rectangular section to be known as strip is 12 inches while the…

Q: According to the API code, pipes of the same nominal diameter should be fitted so the offset is no…

A: The welding of pipes should be done by the qualified workers. The offset for same nominal diameters…

Q: 6 kip/ft 8 kip AB A 9 ft 4.5 ft 5 ft -

A:

Q: Explain how the hyperbaric chamber helps to cure the bends

A: A hyperbaric chamber helps to cure the bends by the mean of a high-pressure chamber, by which a…

Q: Engine oil at 87°C flows entire plate.

A:

Q: the minimum metric

A: Given; For the three bolt system shown in the figure,shear yield strength=200 MPaFOS=2The min.…

Q: The cause of an induced angle

A: Solution ;

Q: 12. The following is concerned with the depth of the hole: * Drilling operation Drilling operation…

A: Blind-hole is defined as the a hole that is drilled or reamed to a certain depth without going…

Q: What is the Minor Loss Coefficient(k-value) of one 45 Degree Elbow using the following data?

A: Given : To find: Minor loss due to 45 degree bend

Q: Differentiate between corrective and improvement maintenance.

A:

Q: a new machine. The n conthoOus use and repair rate of 0.10 per day Compute the machine inherent…

A: Given   Repair rate, R = 0.1   Failure rate, F = 0.021 Find   Machine availability, A

Fluid Kinematics

The branch of science that deals with objects which are either in motion or stationary are studied under the branch of classical mechanics. Fluid mechanics is a subcategory of classical mechanics that deals with the behavior of fluids at rest (fluid statics) or in motion (posing some velocity). In fluid kinematics, studies focus on the associated motion of fluid particles or groups of particles, and its associated parameters like displacements, velocity, and acceleration without concerning about the forces that caused the motion. All the laws of classical mechanics are applied in the study of fluid kinematics.