Automotive Technology
7th Edition
ISBN: 9781337794213
Author: ERJAVEC, Jack.
Publisher: Cengage,
expand_more
expand_more
format_list_bulleted
Concept explainers
Textbook Question
Chapter 45, Problem 4SA
Define dynamic and static wheel balance.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solutionStudents have asked these similar questions
Mom and vibrations
c) Explain why the wheel/tire balancing is necessary.
List the various methods used by traction control systems to eliminate wheel spin.
While discussing steering problems: Technician A says that a “jerky” steering wheel and a “clunking” noise could indicate worn steering column U-joints. Technician B says that lack of assist and a “growling” noise in a fluid-filled steering pump could indicate a hose or pump internal restriction. Who is correct?
Chapter 45 Solutions
Automotive Technology
Ch. 45 - List five things that could cause premature...Ch. 45 - Define lateral and radial runout.Ch. 45 - Prob. 3SACh. 45 - Define dynamic and static wheel balance.Ch. 45 - Describe the proper procedure to seal a puncture...Ch. 45 - The rim offset is the vertical distance between...Ch. 45 - Prob. 7SACh. 45 - Explain why a TPMS relearn should be performed...Ch. 45 - A tire that wobbles from side-to-side is said to...Ch. 45 - A front tire has excessive wear on both edges of...
Ch. 45 - All of the following statements are correct...Ch. 45 - All of the following statements are correct...Ch. 45 - Which of the following statements about sidewall...Ch. 45 - All of these statements about improper wheel...Ch. 45 - Prob. 7MCCh. 45 - Technician A says that the front wheel bearings on...Ch. 45 - Technician A says that dynamic wheel imbalance...Ch. 45 - Technician A says that front bearing assembly...Ch. 45 - Technician A says that replacement wheel rims...Ch. 45 - Prob. 5ASRQCh. 45 - While choosing the correct tire for a vehicle:...Ch. 45 - Technician A says that on most vehicles, the...Ch. 45 - Prob. 8ASRQCh. 45 - Prob. 9ASRQCh. 45 - Prob. 10ASRQ
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- Describe the differences between passive and active wheel speed sensors.arrow_forwardAll of these statements about improper wheel balance are true except? a. Dynamic imbalance may cause wheel shimmy. b. Dynamic imbalance may cause steering pull in either direction. c. Static imbalance causes wheel tramp. d. Static imbalance causes rapid wear on suspension components.arrow_forwardWhen adjusting a vehicle to counter the effect of road crown, what is the adjustment would you make-Adjust the left front wheel with slightly less positive caster-Adjust the right front wheel with slightly less positive caster-Adjust the right front wheel with slightly more positive camber-Adjust both front wheels with slight toe-outarrow_forward
- Tech A says that the presence of a thrust angle can cause poor directional stability on ice, snow or a wet pavement. Tech B says that it can also increase tire wear because the front wheels fight the rear ones for steering control, Who is correctarrow_forwardWhile diagnosing the cause of wheel shimmy: Technician A says that this problem can be caused by loose wheel bearings. Technician B says that this can be caused by binding steering column U-joints. Who is correct? a. Technician A only b. Technician B only c. Both A and B d. Neither A nor Barrow_forwardDescribe thrust angle and why it is important foi wheel alignmentarrow_forward
- Why are the wires leading to some wheel-speed sen sors twisted?arrow_forwardWhich is the least likely cause of hard steering? a. Worn rack spool valve seals b. Insufficient drive belt tension c. Kinked power-steering pressure line d. Loose steering column U-jointarrow_forwardexplain the concept of the virtual steering axis compared to traditional suspensionarrow_forward
- Technician A says a wheel alignment rack should include rear slip plates. Technician B says a four wheel alignment can be performed on a 2 wheel alignment machine with some extra work. who is correct?arrow_forwardexplain the purpose of the the wheel rim drop center and safty ridges ?arrow_forwardExplain briefly the Two-and Four-Wheel Tractors.arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Automotive Technology: A Systems Approach (MindTa...Mechanical EngineeringISBN:9781133612315Author:Jack Erjavec, Rob ThompsonPublisher:Cengage LearningAutomotive TechnologyMechanical EngineeringISBN:9781337794213Author:ERJAVEC, Jack.Publisher:Cengage,
Automotive Technology: A Systems Approach (MindTa...
Mechanical Engineering
ISBN:9781133612315
Author:Jack Erjavec, Rob Thompson
Publisher:Cengage Learning
Automotive Technology
Mechanical Engineering
ISBN:9781337794213
Author:ERJAVEC, Jack.
Publisher:Cengage,
Introduction To Engg Mechanics - Newton's Laws of motion - Kinetics - Kinematics; Author: EzEd Channel;https://www.youtube.com/watch?v=ksmsp9OzAsI;License: Standard YouTube License, CC-BY